A Consortium Blockchain Based Overseas Fund Transfer System

Domestic fund transfers are all the time immediate, handier and obtainable however in overseas fund transfer, funds are transferred from payers account to payees account through the correspondent banks, central bank and messaging network which involves intermediaries and allied charges. Blockchain Technology has grabbed the interest of financial systems due to its inventive benefits such as decentralised structure, faster speed, cost-effectiveness and more security over conventional approaches. Adopting Blockchain Technology for overseas fund transfer can overcome the transaction delays, intermediaries’ failures and recurring costs involved in the current system. In this paper, a Consortium Blockchain based overseas fund transfer process is proposed to achieve faster operations, security and transparency. Hyperledger Fabric Blockchain framework has been used for overseas fund transfer process and web-user interface is developed for the same. Simulation results demonstrate the significance of Blockchain as a promising technology for overseas fund transfer process to facilitate speed, security, transparency and efficiency for overseas fund transfer.

     

Manifold Preserving Features and Regression for Semantic Labelling in High Dimensional Images

Wireless Personal Communications - This paper proposes an combined method for manifold preservation and Subspace Eigenvectors(SE) based regression in high dimensional (HD) images. We studied...     

Thermoelectric Properties of Two-Phase PbTe with Indium Inclusions

The thermoelectric figure of merit (zT) can be increased by introduction of additional interfaces in the bulk to reduce the thermal conductivity. In this work, PbTe with a dispersed indium (In) phase was synthesized by a matrix encapsulation technique for different In concentrations. x-Ray diffraction analysis showed single-phase PbTe with In secondary phase. Rietveld analysis did not show In substitution at either the Pb or Te site, and this was further confirmed by room-temperature Raman data. Low-magnification (~1500×) scanning electron microscopy images showed micrometer-sized In dispersed throughout the PbTe matrix, while at high magnification (150,000×) an agglomeration of PbTe particles in the hot-pressed samples could be seen. The electrical resistivity (ρ) and Seebeck coefficient (S) were measured from 300 K to 723 K. Negative Seebeck values showed all the samples to be n-type. A systematic increase in resistivity and higher Seebeck coefficient values with increasing In content indicated the role of PbTe-In interfaces in the scattering of electrons. This was further confirmed by the thermal conductivity (κ), measured from 423 K to 723 K, where a greater reduction in the electronic as compared with the lattice contribution was found for In-added samples. It was found that, despite the high lattice mismatch at the PbTe-In interface, phonons were not scattered as effectively as electrons. The highest zT obtained was 0.78 at 723 K for the sample with the lowest In content.     

Beneficial effects of wettability altering surfactants in oil-wet fractured reservoirs

In fractured reservoirs, an effective matrix-fracture mass transfer is required for oil recovery. Surfactants have long been considered for oil recovery enhancement, mainly in terms of their ability to reduce oil–water interfacial tension. These surfactants are effective when the fractured formations are water-wet, where capillary imbibition of surfactants from the fracture into the matrix contributes to oil recovery. However, another beneficial aspect of surfactants, namely their ability to alter wettability, remains to be explored and exploited. Surfactants capable of altering wettability can be especially beneficial in oil-wet fractured formations, where the surfactant in the fracture diffuses into the matrix and alters the wettability, enabling imbibition of even more surfactant into the matrix. This sequential process of initial diffusion followed by imbibition continues well into the matrix yielding significant enhancements in oil recovery.In order to test this hypothesis of sequential diffusion–imbibition phenomenon, Dual-Drop Dual-Crystal (DDDC) contact angle experiments have been conducted using fractured Yates dolomite reservoir fluids, two types of surfactants (nonionic and anionic) and dolomite rock substrates. A new experimental procedure was developed in which crude oil equilibrated with reservoir brine has been exposed to surfactant to simulate the matrix-fracture interactions in fractured reservoirs. This procedure enables the measurements of dynamic contact angles and oil–water interfacial tensions, in addition to providing the visual observations of the dynamic behavior of crude oil trapped in the rock matrix as it encounters the diffusing surfactant from the fractures. Both the measurements and visual observations indicate wettability alterations of the matrix surface from oil-wet to less oil-wet or intermediate wet by the surfactants. Thus this study is of practical importance to oil-wet fractured formations where surfactant-induced wettability alterations can result in significant oil recovery enhancements. In addition, this study has also identified the need to include contact angle term in the dimensionless Bond number formulations for better quantitative interpretation of rock–fluids interactions.     

First-Principles Investigation of Electronic Properties of GaAsxSb1 –x Ternary Alloys

Semiconductors - Compositional variations in GaAs based ternary alloys have exhibited wide range alterations in electronic properties. In the present paper, first-principles study of...     

Analysis of Test Application Time for Test Data Compression Methods Based on Compression Codes

We present an analysis of test application time for test data compression techniques that are used for reducing test data volume and testing time in system-on-a-chip (SOC) designs. These techniques are based on data compression codes and on-chip decompression. The compression/decompression scheme decreases test data volume and the amount of data that has to be transported from the tester to the SOC. We show via analysis as well as through experiments that the proposed scheme reduces testing time and allows the use of a slower tester. Results on test application time for the ISCAS'89 circuits are obtained using an ATE testbench developed in VHDL to emulate ATE functionality.     

Solar drying vs. open sun drying: A framework for financial evaluation

Initiatives towards large-scale dissemination of solar dryers for drying of agri-produce face severe competition from the largely prevalent practice of open sun drying in most of the developing countries. Therefore, solar drying systems must offer exceptionally attractive financial gains to enhance their acceptance among the potential users. A modest attempt to develop a simple framework to facilitate a comparison of the financial feasibility of solar drying as against open sun drying has been made in the present work. Results of some exemplifying calculations are presented and briefly discussed.     

Freezing-induced splashing during impact of molten metal droplets with high Weber numbers

The impact of molten tin droplets (0.6 mm diameter) on solid surfaces was observed for a range of impact velocities (10–30 m/s), substrate temperatures (25–200 °C) and substrate materials (stainless steel, aluminum and glass). The substrate was mounted on the rim of a rotating flywheel and the collision of single droplets with the moving substrate was photographed. Droplet impact Reynolds number ranged from 2.2 × 10⁴ to 6.5 × 10⁴ and Weber number from 8.0 × 10² to 7.2 × 10³. On a hot surface there was no splashing and droplets spread to form disk-like splats with smooth edges. Solidification around the edges of droplets spreading on cold surfaces created a solid rim that obstructed flow and triggered splashing. An analytical model was developed to predict the transition temperature at which splashing disappeared by assuming that the thickness of the solid layer had to equal that of the splat in the time the droplet spread to its maximum extent in order to obstruct liquid flow. The model predicted the transition temperature for aluminum and stainless steel surfaces, assuming that thermal contact resistance between the droplet and substrate varied between 10⁻⁶ and 10⁻⁷ m² K/W. The model also predicted that tin droplets would not splash on glass surfaces maintained at or above room temperature, and this was confirmed by experiments.     

Incidence of vibrios of public health significance in the farming phase of tiger shrimp (Penaeus monodon)

The incidence of some of the human pathogenic vibrios in the cultured tiger shrimp (Penaeus monodon) was evaluated during the farming phase in practice at a commercial semi-intensive shrimp farm off Uttarakannada, Karnataka (India). Possible sources of these human pathogens were also evaluated. Vibrio alginolyticus was found to be the most common Vibrio member (57% incidence). Vibrio cholerae, V parahemolyticus and V vulnificus were the other species encountered. All these occurred in shrimp pond sediment, pond water and the feed used (clam meat and formulated feed). Vibrio mimicus was encountered only in the dam meat used as a shrimp feed. A poor correlation between the faecal coliform level and the occurrence of these pathogenic vibrios was apparent, implying natural occurrence of these vibrios in the brackishwater/shrimp culture environment.     

A 223- $$mu W$$ μ W single-to-differential RF mixer with 8.6dBm IIP3 using current-bleeding and body-effect for sub-6 GHz 5G applications

Analog Integrated Circuits and Signal Processing - As the 5G era beckons in the world of communication and information technology, there is a surge in demand for battery-operated, mobile wireless...