Grafting of vinyl monomers onto natural rubber,II. Graft copolymerization of methyl methacrylate onto natural rubber using tetravalent ceric ions

The use of tetravalent ceric ions to initiate graft-copolymerization of methyl methacrylate onto natural rubber (NR) has been investigated. The rate of grafting has been determined by varying the concentration of monomer and cerium(IV), the temperature and the solvents. The graft yield increases with increasing monomer concentration up to 1.877 M, with further increase of the monomer, the graft yield decreases. The percentage of grafting increases with increasing cerium(IV) concentration up to 0.035 M, thereafter it decreases. With increasing temperature the graft yield increases. The effect of CuSO₄ on the rate of grafting has also been investigated. A plausible mechanism has been suggested and the kinetic rate expressions have been derived.     

Processing and physical properties of native grass-reinforced biocomposites

Big blue stem grass fiber-reinforced high density polyethylene powder biocomposites were fabricated using two separate processing schemes: (1) by compounding biofiber with the thermoplastic powder in an extruder and subsequently injection molding the extrusion pellets and (2) by combining biofiber and the powder thermoplastic powder using a modified sheet molding compounding (SMC) line and subsequently compression molding the sheet material. The physical properties including storage modulus, heat deflection temperature (HDT), notched Izod impact strength, and morphology were evaluated with dynamic mechanical analysis, Izod impact strength measurement, and microscopy observation. It was found that compression-molded specimens achieved similar modulus values to injection molded specimens for grass-reinforced high density polyethylene (HDPE) composites. The stiffness of the compression-molded specimens is related to the consolidation state of the samples, which depends on compression molding conditions such as temperature, pressure, and mold type. Compression-molded specimens exhibited a higher HDT and notched Izod impact strength compared to injection-molded samples. Grass fiber-reinforced cellulose acetate butyrate (CAB) biocomposites made with SMC processing had similar physical properties with grass fiber-reinforced HDPE composites, which indicates that natural fiber-reinforced CAB biocomposites have the potential to replace polyolefin-based composites for automotive applications. POLYM. ENG. SCI. 47:969–976, 2007. © 2007 Society of Plastics Engineers.     

Low intensity visual data improvement using DWT and LWT based regularizer

Image Completion plays a vital role in compressed sensing, machine learning, and computer vision applications. The Rank Minimization algorithms are used to perform the image completion. The major problem with rank minimization algorithms is the loss of information in the recovered image at high corruption ratios. To overcome this problem Lifting wavelet transform based Rank Minimization (LwRM), and Discrete wavelet transform based Rank Minimization (DwRM) methods are proposed, which can recover the image, if the corrupted observations are more than 80%. The evaluation of the proposed methods are accomplished by Full Reference Image Quality Assessment (FRIQA) and No Reference Image Quality Assessment (NR-IQA) metrics. The simulation results of proposed methods are superior to state-of-the-art methods.

     

DeepRan: Attention-based BiLSTM and CRF for Ransomware Early Detection and Classification

Information Systems Frontiers - Ransomware is a self-propagating malware encrypting file systems of the compromised computers to extort victims for financial gains. Hundreds of schools, hospitals,...     

Generalizing Multi-agent Graph Exploration Techniques

International Journal of Control, Automation and Systems - The system of multiple agents working in coordination for a given task has several advantages on faster completion, fault-tolerance, etc....     

Evaluating the role of composition and local structure on alkali out-diffusion in glasses for thin-film solar cells

The presence of alkali ions has reportedly improved the performance of CIGS/CZTS–based thin-film solar cells. The out-diffusion of the alkali ion, in particular, Na, from the glass substrate offers a facile scalable route of supplying the alkali ions during the growth of the absorber layer. In this work, we demonstrate the diffusion of different alkali ions (Li/Na/K) from composition tuned glasses with intentionally incorporated excess alkali ions into a thin Mo film, typically used as a bottom electrode in solar cells. We also evaluate the physical, mechanical, and thermal properties of the glasses for suitability as a substrate in thin-film deposition. The out-diffusion of alkali ions to the overlayer is found to be critically influenced by the composition and the local structure of the glasses. The Na ions exhibit the highest extent of diffusion among the alkali ions present in glass substrates, while that for the K-ions is the lowest. For the glasses with mixed alkali ions, the presence of Li facilitated the out-diffusion of Na, whereas K ions appear to inhibit the same. Differently with the existing reports, we show that the activation energy and the presence of Ca ions as additional modifiers play a crucial role in the transport mechanism of the ions. In addition, the synthesized glasses exhibit hardness of the order 5-7 GPa, density ~2.55 g cm^-3. The glass transition temperature lies between 535 and 580°C and the coefficient of thermal expansion 8.5-10 ppm/K, which is highly suitable for use as substrates in thin-film solar cells.     

Improving delamination resistance of carbon fiber reinforced polymeric composite by interface engineering using carbonaceous nanofillers through electrophoretic deposition: An assessment at different in-service temperatures

In this article, modification of carbon fiber surface by carbon based nanofillers (multi-walled carbon nanotubes [CNT], carbon nanofibers, and multi-layered graphene) has been achieved by electrophoretic deposition technique to improve its interfacial bonding with epoxy matrix, with a target to improve the mechanical performance of carbon fiber reinforced polymer composites. Flexural and short beam shear properties of the composites were studied at extreme temperature conditions; in-situ cryo, room and elevated temperature (−196, 30, and 120°C respectively). Laminate reinforced with CNT grafted carbon fibers exhibited highest delamination resistance with maximum improvement in flexural strength as well as in inter-laminar shear strength (ILSS) among all the carbon fiber reinforced epoxy (CE) composites at all in-situ temperatures. CNT modified CE composite showed increment of 9% in flexural strength and 17.43% in ILSS when compared to that of unmodified CE composite at room temperature (30°C). Thermomechanical properties were investigated using dynamic mechanical analysis. Fractography was also carried out to study different modes of failure of the composites.     

Effects of fiber surface grafting by functionalized carbon nanotubes on the interfacial durability during cryogenic testing and conditioning of CFRP composites

Carbon fiber reinforced epoxy (CE) composite is ideal for a cryogenic fuel storage tank in space applications due to its unmatched specific strength and modulus. In this article, inter-laminar shear strength (ILSS) of carbon fiber/epoxy (CE) composite is shown to be considerably improved by engineering the interface with carboxyl functionalized multi-walled carbon nanotube (FCNT) using electrophoretic deposition technique. FCNT deposited fibers from different bath concentrations (0.3, 0.5, and 1.0 g/L) were used to fabricate the laminates, which were then tested at room (30°C) and in-situ liquid nitrogen (LN) (−196°C) temperature as well as conditioning for different time durations (0.25, 0.5, 1, 6, and 12 h) followed by immediate RT testing to study the applicability of these engineered materials at the cryogenic environment. A maximum increment in ILSS was noticed at bath concentration of 0.5 g/L, which was ~21% and ~ 17% higher than neat composite at 30°C and − 196°C, respectively. Short-term LN conditioning was found to be detrimental due to developed cryogenic shock, which was further found to be compensated by cryogenic interfacial clamping upon long-term exposure.     

Mechanical behavior of electrophoretically modified CFRP composites at elevated temperatures: An assessment of the influence of graphene carboxyl bath concentration

The study aims at investigating the mechanical behavior of carbon fiber reinforced polymer (CFRP) composites modified with graphene carboxyl at elevated temperature (ET-110°C) and understanding the effect of electrophoretic deposition bath concentration (0.5 g/L, 1.0 g/L, and 1.5 g/L) on their mechanical behavior at ET. The 1.5 g/L composite has revealed a maximum improvement in energy absorbed before failure of 33.25% at RT and 22.54% at ET for flexural testing and ∼35% at RT for short beam shear testing, over neat CFRP composite. The modified composites have shown an improved flexural strain to failure at both RT and ET, with 1.5 g/L composite exhibiting maximum enhancement of 12.41% at RT and 26.52% at ET over neat composite. However, at ET, modified composites exhibited lower flexural strength and interlaminar shear strength values in comparison to that of neat. Viscoelastic behavior of all composites was studied to understand bath concentration's effect on thermal behavior via dynamic mechanical thermal analysis. Differential scanning calorimetry was employed for governing the glass transition temperature of composites. Fractography of tested samples (both ET and RT) was performed utilizing a scanning electron microscope to determine the prominent failure mode.     

Effect ofθ-alumina formation on the growth kinetics of alumina-forming superalloys

Alumina-forming ODS superalloys are excellent oxidation-resistant materials. Their resistance relies upon the establishment of a stable, slow-growing, and adherent -alumina. In the present investigation, these alloys exhibited unstable and relatively less adherent -alumina phase, which increased the oxidation rate in the transient stage and converted into -alumina in the later part of the exposure. The oxide-growth process was found to depend upon various parameters such as temperature, time, and presence of an active elecment in the superalloy. Characterization carried out by XRD, SEM/EDAX, and AES on oxidized ODS and non-ODS alloys demonstrated a significant influence of the active element, Y, on the transformation of - to -alumina. SIMS analysis of two-stage oxidation at 900°C for two different durations evidently showed that the change in the transport process is due to -to--alumina transformation. On the basis of these results, a new and consistent mechanism is proposed to explain the influence of -alumina and its transformation on growth kinetics and the effect of yttrium on the transformation leading to good scale adherence and oxidation resistance.