Medical Positron Imaging with a Dense Drift Space MultiWire Proportional Chamber

A multiplanar positron camera is proposed, made of six MWPC modules, arranged to form the lateral surface of a hexagonal prism. Each 50 x 50 cm(2) module has a single MWPC sandwiched by two 2-cm thick lead glass tube converters. The experimental results for a 15 x 15 cm(2) test module are reported. For 511 keV gamma-rays incident almost perpendicular onto a 1.0-cm thick converter, a detection efficiency of 4.3%, a time resolution of 130 ns (FWHM) and a spatial resolution of 2.8 mm (FWHM) have been measured with a standard Argon-Methane (70-30) mixture at 1.2 atm. The chamber may also be operated in high resolution mode: 1.2-mm (FWHM) spatial resolution has been measured at a 50% lower efficiency. The use of fast delay lines (specific delay 8 ns/cm) for the position read-out ensures a high rate capability. The expected performance of the six-module MWPC camera is discussed and compared with that of a BGO crystal ring camera. The MWPC solution seems very attractive not only for its low cost and simplicity of construction, but also for its fully three-dimensional imaging capability.     

Optimal hardware and software design of an image-based system for capturing dynamic movements

In contrast to conventional image-capture systems, which attempt to minimize the amount of data collected during capture, typically by using hardware filters, the more general condition of using all information captured on a camera sensor is much more challenging and requires rigorous consideration of the hardware and software pipelines to obtain accurate tracking results. In this paper, this issue is specifically addressed by describing a unique hardware and software design implemented for use as a fully image-based capture system. An attempt is made to minimize the cost of this system by maximizing hardware control through software implementation. The hardware and software requirements are described in the context of the desired high-speed capture suitable for earthquake motions or other dynamic movements in a scene. Experiments are conducted and presented illustrating the good performance and stability of the system. This system is deemed suitable for the general condition of a building interior.     

Controlled density of vertically aligned carbon nanotubes in a triode plasma chemical vapor deposition system

We report on the growth mechanism and density control of vertically aligned carbon nanotubes using a triode plasma enhanced chemical vapor deposition system. The deposition reactor was designed in order to allow the intermediate mesh electrode to be biased independently from the ground and power electrodes. The CNTs grown with a mesh bias of + 300 V show a density of ∼ 1.5 μm^− 2 and a height of ∼ 5 μm. However, CNTs do not grow when the mesh electrode is biased to − 300 V. The growth of CNTs can be controlled by the mesh electrode bias which in turn controls the plasma density and ion flux on the sample.     

Substrate rotation effects on β-FeSi2 epitaxial film growth using MBE

This study showed that substrate rotation plays an important role in the growth of high-quality β-FeSi₂ epitaxial film on hydrogen terminated Si (1 1 1) substrate using molecular beam epitaxy (MBE). The present work elucidated the substrate rotation effects on morphology, thickness, and purity. Results verified that substrate rotation is essential to grow thicker epilayers with better morphology and compositional uniformity. In addition, purity analyses indicated that substrate rotation increases the concentration of non-metallic impurities (H, C, and O), but does not further introduce metallic impurities into β-FeSi₂ films.     

A miniature UWB planar monopole antenna with 5-GHz band-rejection filter and the time-domain characteristics

A planar monopole antenna with a staircase shape and small volume (25/spl times/26/spl times/1 mm/sup 3/) is proposed in this paper. With the use of a half-bowtie radiating element, the staircase-shape, and a modified ground plane structure, the proposed antenna has a very wide impedance bandwidth measured at about 11.6 GHz (2.9-14.5 GHz, bandwidth ratio about 1:5) below VSWR 2 including the WLAN band notched in the vicinity of 5 GHz. An omnidirectional radiation pattern is obtained. The group delay which is an indication of linearity between two proposed antennas is less than 1 ns. The electrical characteristics in terms of frequency and time domains and physical ones of the proposed antenna make it attractive for use in ultrawideband (UWB) systems.     

Selective wet etching of p-GaN for efficient GaN-based light-emitting diodes

The selective wet etching of a p-GaN layer by using a solution of KOH in ethylene glycol (KE) was studied to enhance the optical and electrical performance of the GaN-based light-emitting diodes (LEDs). The surface of the p-GaN, which was selectively etched in the KE solution, showed hexagonal-shaped etch pits. The light-output power of etched LEDs was improved by 29.4% compared to that of the nonetched LED. This improvement was attributed to the increase in the probability of photons to escape due to the increased surface area of textured surface and the reduction in contact resistance of the ohmic layer resulting from the increased contact area and hole concentration on the textured p-GaN. The reverse leakage current of the LED was also greatly decreased due to the surface passivation and the removal of defective regions from the p-GaN.     

Advances in Vapor Pressure Modeling for Electronic Packaging

Two advanced techniques have been developed for modeling vapor pressure within the plastic IC packages during solder reflow. The first involves the extension of the "wetness" technique to delamination along multimaterial interface and during dynamic solder reflow. Despite its simplicity, this technique is capable of offering reliable and accurate prediction for packages with high flexural rigidity. For packages with low flexural rigidity, the new "decoupling" technique that integrates thermodynamics, moisture diffusion, and structural analysis into a unified procedure has been shown to be more useful. The rigorous technique has been validated on both leadframe-based as well as laminate-based packages. With high accuracy and computational efficiency, these dynamic modeling tools will be valuable for optimization of package construction, materials, and solder reflow profile against popcorn cracking for both SnPb and Pb-free solders     

Symbol error rate of selection amplify-and-forward relay systems

Cooperative diversity schemes significantly improve the performance of wireless networks by transmitting the same information through several nodes. The amplify-and-forward (AF) relaying method is one of the most attractive cooperative diversity schemes due to its low complexity. Selection AF relaying has recently been proven to achieve the same diversity order as and lower outage probability than all-participate relays. In this letter, we present an asymptotic analysis of the symbol error rates of a selection AF network, and compare it with the conventional all-participate scheme     

High-performance 94-GHz single balanced mixer using 70-nm MHEMTs and surface micromachined technology

We reported 94-GHz, low conversion loss, and high isolation single balanced active gate mixer based on 70-nm gate length InGaAs/InAlAs metamorphic high-electron mobility transistors (MHEMTs). This mixer showed that the conversion loss and isolation characteristics were 2.5/spl sim/3.5 dB and under -29 dB in the range of 92.95/spl sim/94.5 GHz, respectively. The low conversion loss of the mixer is mainly attributed to the high-performance of the MHEMTs exhibiting a maximum drain current density of 607 mA/mm, an extrinsic transconductance of 1015 mS/mm, a current gain cutoff frequency (f/sub t/) of 330 GHz, and a maximum oscillation frequency (f/sub max/) of 425 GHz. High isolation characteristics are due to hybrid ring coupler which adopted dielectric-supported air-gapped microstrip line structure using surface micromachined technology. To our knowledge, these results are the best performance demonstrated from 94 GHz single balanced mixer utilizing GaAs-based HEMTs in terms of conversion loss as well as isolation characteristics.