A power-driven multiplication instruction-set design method for ASIPs

This paper presents a novel power-driven multiplication instruction-set design method for application-specific instruction-set processors (ASIPs). Based on a dual-and-configurable-multiplier structure, our proposed method devises a multiplication instruction set for low-power ASIPs. Our method exploits the execution sequences of multiplication instructions and effective bit widths of variables to reduce power consumed by redundant multiplication bits while minimizing the multiplication execution time. Experimental results on a set of DSP programs demonstrate that our proposed method achieves significant power reduction (up to 18.53%) and execution time improvement (up to 10.43%) with 18% area overhead.     

A possibilistic clustering approach to novel fault detection and isolation

In this paper, a new approach for fault detection and isolation that is based on the possibilistic clustering algorithm is proposed. Fault detection and isolation (FDI) is shown here to be a pattern classification problem, which can be solved using clustering and classification techniques. A possibilistic clustering based approach is proposed here to address some of the shortcomings of the fuzzy c-means (FCM) algorithm. The probabilistic constraint imposed on the membership value in the FCM algorithm is relaxed in the possibilistic clustering algorithm. Because of this relaxation, the possibilistic approach is shown in this paper to give more consistent results in the context of the FDI tasks. The possibilistic clustering approach has also been used to detect novel fault scenarios, for which the data was not available while training. Fault signatures that change as a function of the fault intensities are represented as fault lines, which have been shown to be useful to classify faults that can manifest with different intensities. The proposed approach has been validated here through simulations involving a benchmark quadruple tank process and also through experimental case studies on the same setup. For large scale systems, it is proposed to use the possibilistic clustering based approach in the lower dimensional approximations generated by algorithms such as PCA. Towards this end, finally, we also demonstrate the key merits of the algorithm for plant wide monitoring study using a simulation of the benchmark Tennessee Eastman problem.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

On Faster I DDQ Measurements

The purpose of this paper is to introduce a new I _DDQ measurement technique based on active successive approximations, called ASA-I _DDQ. This technique has unique features facilitating a speed-up in I _DDQ measurement. Experimental results suggest that a significant speed-up factor (up to 4) can be obtained over the QuiC-Mon technique. Such a speed-up is a key element in the replacement of single-threshold I _DDQ testing since it amplifies the effectiveness of post-processing techniques.     

Formation and inhibition of free radicals in electrically stressed and aged insulating polymers

Previous work has shown that prebreakdown, electrical aging, and breakdown phenomena are directly associated with charge carriers injected from electrical contacts and their subsequent dissociative trapping and recombination. In addition, the energy released from each trapping or recombination event is dissipated in the breaking of the bonds of macromolecules, thus forming free radicals and new traps in the electrically stressed insulating polymers, as predicted by Kao's model. It is this gradual degradation process that leads to electrical aging and destructive breakdown. New experimental results are presented to confirm previous findings and a new approach to inhibit the degradation process by the incorporation of suitable dopants into the polymer. The concentration of free radicals in the polymer increases with an increasing electric field at a fixed stress time of 250 h and with increasing stress time at a fixed electric field of 833 kV cm^?1. The concentration of free radicals is directly related to the concentration of new traps created by stress. However, when suitable dopants are incorporated, the initiation voltage for the occurrence of electrical treeing and the breakdown strength are both increased. The dopants tend to create shallow traps and have little effect on the deep trap concentration. This implies that the dopants act as free‐radical scavengers that tend to satisfy the unpaired electrons of the broken bonds, which create new acceptor‐like electron traps and new shallow traps. By doing so, the shallow traps screen the deep traps, thereby reducing the energy released during trapping and recombination and the probability of breaking the macromolecular bonds and causing structural degradation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3416–3425, 2003     

Analysis of an extensive measurement program developed from the start up to the follow up of the operation of the CNAAA NPP

Integrated tests (IT) applied to the Units I and II of the CNAAA Nuclear Power Plants (Angra dos Reis, Rio de Janeiro, Brazil) vara part of a comprehensive test program required to have the commercial operational licence issued. The IT cover operation at zero power and the subsequent power levels (the power escalation) until the nominal power operation.

This paper reports and compares the results of systematic neutron and gamma equivalent dose-rate measurements performed inside and outside the reactor containment of each Unit, during the start-up phase of the operation, for different power levels of the reactors. It also compares the collective-doses measured along the operation of the two units of the CNAAA wich similar data of the Grafenrheinfeld nuclear power plant (Germany) — basic-of-project for the CNAAA — Unit II — and analyses the data under the fight of the state-of-art.