On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

参数化图形库技术

本文论述了参数化图形库的实现原理，建立了以尺寸叠加算法为基础的参数化图形库开发工具，利用这种开发工具建立的图形数据可以由数据库管理，方便有效。     

新型实用布线算法──L─M算法

本文提出新型布线算法，集李氏迷宫法与线搜索法的长处为一体，以饱和带法进行动态排序，以线搜索法确定借孔位置，然后用李氏法进行单层布线，获得最佳路径，从而达到线型好，布通率高的效果。     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

碳/碳复合材料CVI工艺中热解碳形成机理的研究

对碳碳复合材料CVI或（CVD）工艺中热碳组织的类型，沉积机理等研究情况进行了简要的综述，并对其进一步研究提出了相应观点。     

ZnGa2O4纳米晶的制备和结构表征

采用喷射共沉淀法制备了ZnGa2O4 纳米晶，XRD、SEM和TEM结构分析结果表明，喷射共沉淀法制备的ZnGa2O4的纳米晶颗粒细小均匀，形状完整，与化学共沉淀法相比，粒子尺寸明显减小，小于10nm，同时ZnO杂相峰消失，分析了喷射共沉淀法的机理，并对实验结果进行了解释。     

标准物质在分析测试中的重要地位及发展前景

标准物质在分析测试领域中无论在定值，方法的研究，误差确定等方面都有着重要地位。标准物质的质量保证及正确使用也应引起我们重视。随着科学技术迅速发展标准物质有着广阔发展前景。     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。