A field study on serum vitellogenin levels in male Reeves' pond turtles (Chinemys reevesii) from estrogen-contaminated sites and a reference site

To ascertain whether wild male turtles were influenced by environmental estrogens, we examined serum vitellogenin (VTG) levels of male Reeves' pond turtles (Chinemys reevesii) collected from four study sites (A-D) in Kyoto, Japan. Sites A-C, which were impacted by domestic or industrial wastewater and effluents from sewage treatment plants, were chosen as contaminated sites, and site D was intended as a reference site. This contaminated/reference site characterization was confirmed by measuring estrogenic activities of the water samples collected at each site for over a year. Serum VTG levels in the turtles were quantified by an enzyme-linked immunosorbent assay established previously. Estrogenic activities of the water samples were measured using a previously validated yeast two-hybrid assay and expressed as the estradiol-17beta equivalent. Estrogenic activity was observed at high levels at sites A-C, but was almost undetected at site D throughout the sampling period: the mean and range were 0.74 (<0.07-2.1), 0.52 (0.17-1.6), 1.7 (<0.07-7.3), and 0.07 (<0.07-0.62) ng/l at sites A-D, respectively. Significant differences were found only in site D versus sites A, B, and C. Therefore, site D and sites A-C were confirmed to be a reference site and contaminated ones, respectively. Overall, 320 male turtles were captured and examined. The majority of the turtles showed normal VTG values (0.10-0.74 microg/ml). Although only five turtles from sites A-C showed unusually high VTG values (1.1-5.9 microg/ml, nearly one order of magnitude higher than normal values but much lower than values in adult females), there was no significant difference in the incidence of these high values between sites A-C and site D. Moreover, among the five turtles, one turtle was captured again 2 months later, but its VTG value dropped to the normal level. The unusually high VTG values may therefore be transient elevation caused by incidental and/or individually specific agents. Excluding the unusually high values, the mean serum VTG (accompanied with the range) was 0.22 (0.10-0.74), 0.27 (0.11-0.62), 0.27 (0.17-0.68), and 0.23 (0.10-0.57) microg/ml at sites A-D, respectively. There were no significant differences in the mean VTG values among sites A-D. Although it should be clarified how and why the unusually high VTG values occurred at sites A-C, our results suggested that wild male C. reevesii turtles would not be significantly affected by xenobiotic estrogens at environmentally relevant levels in terms of serum VTG elevation.     

Cobalt loaded organic acid modified kaolin clay for the enhanced catalytic activity of hydrogen release via hydrolysis of sodium borohydride

Inorganic acids such as hydrochloric acid (HCl), nitric acid (HNO₃) and sulphuric acid (H₂SO₄) are generally used in the acid modification of clays. Here, CoB catalyst was synthesized on the acetic acid-activated kaolin support material (CH₃COOH -kaolin- CoB) with an alternative approach. This prepared catalyst, firstly, was used to catalyze the hydrolysis of NaBH₄ (NaBH₄-HR). The structure of the raw kaolin, kaolin-CH₃COOH, and CH₃COOH-kaolin-CoB samples were characterized by X-ray diffraction spectroscopy (XRD), Fourier transforms infrared spectroscopy (FTIR), scanning electron microscope (SEM), and nitrogen adsorption. At the same time, this catalyst performance was examined by Co loading, NaBH₄ concentration, NaOH concentration, temperature and reusability parameters. The end times of this hydrolysis reaction using raw kaolin-CoB and CH₃COOH-kaolin-CoB were found to be approximately 140 and 245 min, respectively. The maximum hydrogen generation rates (HGRs) obtained at temperatures 30 °C and 50 °C were 1533 and 3400 mL/min/g_catalyst, respectively. At the same time, the activation energy was found to be 49.41 kJ/mol.     

Damage and replication checkpoint control in fission yeast is ensured by interactions of Crb2, a protein with BRCT motif, with Cut5 and Chk1

Fission yeast Cut5/Rad4 plays a unique role in the genome maintenance as it is required for replication, replication checkpoint, and normal UV sensitivity. It is unknown, however, how Cut5 protein is linked to other checkpoint proteins, and what part it plays in replication and UV sensitivity. Here we report that Cut5 interacts with a novel checkpoint protein Crb2 and that this interaction is needed for normal genome maintenance. The carboxyl terminus of Crb2 resembles yeast Rad9 and human 53BP1 and BRCA1. Crb2 is required for checkpoint arrests induced by irradiation and polymerase mutations, but not for those induced by inhibited nucleotide supply. Upon UV damage, Crb2 is transiently modified, probably phosphorylated, with a similar timing of phosphorylation in Chk1 kinase, which is reported to restrain Cdc2 activation. Crb2 modification requires other damage-sensing checkpoint proteins but not Chk1, suggesting that Crb2 acts at the upstream of Chk1. The modified Crb2 exists as a slowly sedimenting form, whereas Crb2 in undamaged cells is in a rapidly sedimenting structure. Cut5 and Crb2 interact with Chk1 in a two-hybrid system. Moreover, moderate overexpression of Chk1 suppresses the phenotypes of cut5 and crb2 mutants. Cut5, Crb2, and Chk1 thus may form a checkpoint sensor-transmitter pathway to arrest the cell cycle.     

Mechanical properties of amorphous alloy compacts prepared by different consolidation techniques

Amorphous alloy compacts of Fe₇₈B₁₃Si₉ prepared by three different techniques (explosive consolidation, high hydrostatic pressure consolidation and warm extrusion) were deformed in compression between 573 and 723 K at a strain rate ranging from 8.3×10^–5–4.2×10^–4s^–1. Explosively consolidated compacts had high strength ranging from 1.9–2.5 GPa below 623 K and could be plastically deformed to a strain of more than 50% at 673 K while preserving the amorphous state. Amorphous alloy compacts prepared by high hydrostatic pressure consolidation showed lower compressive strength. Those produced by warm extrusion were anisotropic in strength, the highest strength being as high as 2.74 GPa. It was also found that the geometry of the starting powders had a profound effect on the strength of the product compacts. Compacts prepared from flaky powders were stronger than those prepared from spherical ones. It is concluded that the mechanical properties of the amorphous alloy compacts depend on the consolidation technique, powder geometry and surface conditions of the powders, especially existence of oxide films.     

Nondestructive sizing of a 3D surface crack generated in a railway component using closely coupled probes for direct-current potential drop technique

The direct-current potential drop technique was applied to the quantitative estimation of the size and shape of the crack generated in railway components. First, calibration equations that relate the potential drop to the crack depth and crack length along with its location were derived where the boundary element method was used for the electric potential problem. The crack depth, crack length and its location were then determined by analyzing an inverse problem by using the quasi-Newton method which compared the potential drop obtained by the calibration equations with measurements using a carbon steel specimen containing a crack. Although the values of depths were slightly scattered because depth estimations were sensitive to the crack location and changed with even a minimal change in distance between the crack and probes, the estimations of lengths and locations were adequate.     

钝化多晶线路中电迁移损伤的预测

1　Introduction　　Thelatestprogressinpackagedsiliconinte gratedcircuits (ICs)isnoteworthy .Withthead vance ,however,someproblemsaboutthedeterio rationofthereliabilityhavebeenraised .Forin stance,thehighercurrentdensityduetoscalingdowncauseselectromigrationininterconnectmetalline.Electromigrationisthetransportationofthemetallicatomsbyelectronwind .Voidsareformedasaresultofdepletionofatoms,andhillocksareformedasaresultofaccumulationofatomsinthemetalline .Thegrowthofvoidsultimatelyleadstometal…     

Nanostructure and mechanical properties of aromatic polyamide and reactive organoclay nanocomposites

Aromatic polyamide/organoclay nanocomposites were synthesized using the solution blending technique. Treatment of montmorillonite clay with p-phenylenediamine produced reactive organophilic clay for good compatibility with the matrix. Polyamide chains were prepared by condensing a mixture of 1,4-phenylenediamine and 4-4′-oxydianiline with isophthaloyl chloride under anhydrous conditions. These chains were end capped with carbonyl chloride using 1% extra acid chloride near the end of reaction to develop the interactions with organoclay. The dispersion and structure–property relationship were monitored using FTIR, XRD, FE-SEM, TEM, DSC and tensile testing of the thin films. The structural investigations confirmed the formation of delaminated and disordered intercalated morphology with nanoclay loadings. This morphology of the nanocomposites resulted in their enhanced mechanical properties. The tensile behavior and glass transition temperature significantly augmented with increasing organoclay content showing a greater interaction between the two disparate phases.     

A simple method for testing the electromigration resistance of solders

Recently, the size of solder bump interconnects have been significantly reduced with the advent of high-density packaging, and thus the evaluation of electromigration in solder bumps has become necessary. The present paper proposes a simple method to test the electromigration resistance of Pb-free solders. One of the key points of the present method is the fabrication of a simple solder sample that can produce sufficient current density to cause electromigration. Moreover, the actual local temperature of a small area subjected to electromigration in the sample was measured by a direct method. A right-angled diamond-shaped hole was introduced in a thin film of solder using a focused-ion-beam system. A direct current was supplied to the film far from the hole, perpendicular to the diagonal of the hole. In this way, the current density was concentrated near to the corner of the hole, and the value of this was obtained through a theoretical analysis. It was noted that the steady temperature in the film along a line extending from the diagonal, remained constant, although the current density decreased gradually far from the corner. Therefore, the temperature at a position near the corner, where electromigration takes place, can easily be found by measuring the temperature far from the corner. The temperature was measured directly under current flow conditions by utilizing the chemical reagents with known melting points. Finally, by measuring the ratio of hillock volume to the time for the current supply as a measure of the atomic flux divergence due to electromigration, the corresponding resistances of some Pb-free solders to electromigration were evaluated.