Electrophoretic Deposition of YSZ Particles on Non-Conducting Porous NiO–YSZ Substrates for Solid Oxide Fuel Cell Applications

This paper reports a method of performing electrophoretic deposition (EPD) on non-conducting substrates overcoming the requirement of a conducting substrate through the use of porous substrates. The conductivity of the substrate is therefore no longer a limiting factor in the application of EPD. This method is applicable to the fabrication of thick or thin layers of ceramic or metal for various applications. As an example, thin and dense yttria-stabilized zirconia (YSZ) layers have been deposited on a non-conducting NiO–YSZ substrate by EPD from a non-aqueous suspension. A solid oxide fuel cell constructed on these sintered bilayers exhibited power densities of 384 and 611 mW/cm² at 750° and 850°C, respectively.     

Oxidation and reforming reactions of CH4 on a stepped Pt(5 5 7) single crystal

The oxidation and reforming kinetics of methane by O₂, CO₂ and H₂O were studied on a stepped Pt(5 5 7) single crystal from 623 to 1050 K under methane rich conditions. The rate of carbon deposition was followed by ex-situ Auger electron spectroscopy under non-oxidative conditions. The apparent activation energy for methane decomposition was significantly lower than the apparent barriers measured for both total oxidation, CO₂ and H₂O reforming. Total oxidation of methane to CO₂ and H₂O followed by combined dry and steam reforming (combined combustion-reforming) led to CO production rates which were higher than direct CO₂ or H₂O reforming rates. The enhanced rates are most likely due to the ability of adsorbed oxygen to prevent carbon nucleation and/or scavenge carbon enabling the reforming reaction to turnover on a larger fraction of sites. Comparable amounts of carbon were found by Auger electron spectroscopy measurements after both direct dry or steam reforming, while combined oxidation-reforming had considerable less carbon. During direct dry or steam reforming, CO₂ and H₂O serve only to scavenge adsorbed atomic carbon, while in the presence of oxygen, carbon is removed by both combustion and reforming routes.     

Synthesis of Organotin Polyamine Ethers Containing Acyclovir and their Preliminary Anticancer and Antiviral Activity

Organotin polyamine ethers containing acyclovir in their backbone were synthesized in moderate to high yield employing the aqueous interfacial polycondensation system. The products are high molecular weight polymers. Infrared spectroscopy of the products shows new bands characteristic of the formation of Sn–N and Sn–O bonds consistent with the proposed structure. MALDI-TOF MS below 2000 Da shows the presence of organotin and acyclovir units containing these two moieties. The products show moderate inhibition of a number of cancer cell lines and exhibit the ability to inhibit a number of viruses, particularly the herpes simplex virus-1 and varicella zoster virus that are responsible for herpes, chicken pox and shingles.     

The influence of styrene–butadiene diblock copolymer on styrene–butadiene–styrene triblock copolymer viscoelastic properties and product performance

The effects of the styrene–butadiene (SB) diblock copolymer on the viscoelastic properties of styrene–butadiene–styrene (SBS) triblock copolymers were examined in both in the the neat state and within specific product applications. The addition of the SB diblock copolymer into a pure SBS triblock copolymer resulted in a significant decrease in the plateau storage modulus and a quantitative linear rise in tan delta. In a pure triblock, in which all endblocks are anchored in polystyrene domains, all entanglements are physically trapped. The SB diblock embodies untrapped polybutadiene endblocks that are able to relax stress by chain reptation through the rubbery polybutadiene matrix. The SB diblock copolymer quantitatively lowered the microphase separation temperature (MST) of the SBS triblock copolymer. These changes in linear viscoelastic behavior manifest themselves into a reduction in the efficiency and performance of the SBS triblock copolymer in asphalt pavement binders and hot-melt adhesive blends. Specifically, the SB diblock diminished the complex shear modulus and elasticity of a polymer-modified asphalt, which translated into lower predicted rutting specification values. The increase in diblock content altered the viscoelastic response of the hot-melt adhesive blend, translating into a reduction in the shear holding power and shear adhesion failure temperature. The lack of network participation, coupled with the relaxation of the polybutadiene endblocks, accounts for the lower strength and greater temperature susceptibility of the diblock-containing systems. © 1995 John Wiley & Sons, Inc.     

Carbonization and liquid-crystal (mesophase) development. 7. Optical textures of cokes from acenaphthylene and decacyclene

Optical textures of cokes prepared by carbonizing acenaphthylene, decacyclene and mixtures thereof at selected values of heat-treatment temperatures and soak time have been compared. Optical textures are assessed using polished surfaces and reflected-polarized-light microscopy in conjunction with a half-wave plate. The acenaphthylene is chemically more reactive than the decacyclene which is itself formed during the carbonization of acenaphthylene. Products of carbonization of acenaphthylene can influence rates of carbonization of the decacyclene. Similar optical textures in cokes cannot be formed by compensating low heat-treatment temperatures with long soak periods. In addition to chemical rate-controlling processes, the physical properties of the system must be acknowledged, in particular the viscosity. Very large non-coalesced growth units of mesophase (800 μm diameter) have been observed. Pre-alignment of growth units of mesophase may occur prior to coalescence.     

Structural and kinetic studies on ligand binding in wild-type and active-site mutants of penicillin acylase

Penicillin acylase catalyses the condensation of Calpha-substituted phenylacetic acids with beta-lactam nucleophiles, producing semi-synthetic beta-lactam antibiotics. For efficient synthesis a low affinity for phenylacetic acid and a high affinity for Calpha-substituted phenylacetic acid derivatives is desirable. We made three active site mutants, alphaF146Y, betaF24A and alphaF146Y/betaF24A, which all had a 2- to 10-fold higher affinity for Calpha-substituted compounds than wild-type enzyme. In addition, betaF24A had a 20-fold reduced affinity for phenylacetic acid. The molecular basis of the improved properties was investigated by X-ray crystallography. These studies showed that the higher affinity of alphaF146Y for (R)-alpha-methylphenylacetic acid can be explained by van der Waals interactions between alphaY146:OH and the Calpha-substituent. The betaF24A mutation causes an opening of the phenylacetic acid binding site. Only (R)-alpha-methylphenylacetic acid, but not phenylacetic acid, induces a conformation with the ligand tightly bound, explaining the weak binding of phenylacetic acid. A comparison of the betaF24A structure with other open conformations of penicillin acylase showed that betaF24 has a fixed position, whereas alphaF146 acts as a flexible lid on the binding site and reorients its position to achieve optimal substrate binding.     

Measurement of soybean fatty acids by near-infrared spectroscopy: Linear and nonlinear calibration methods

A key element of successful development of new soybean cultivars is availability of inexpensive and rapid methods for measurement of FA in seeds. Published research demonstrated applicability of NIR spectroscopy for FA profiling in oilseeds. The objectives of this study were to investigate the applicability of NIR spectroscopy for measurement of FA in whole soybeans and compare performance of calibration methods. Equations were developed using partial least squares (PLS), artificial neural networks (ANN), and support vector machines (SVM) regression methods. Validation results demonstrated that (i) equations for total saturates had the highest predictive ability (r ²=0.91–0.94) and were usable for quality assurance applications, (ii) palmitic acid models (r ²=0.80–0.84) were usable for certain research applications, and (iii) equations for stearic (r ²=0.49–0.68), oleic (r ²=0.76–0.81), linoleic (r ²=0.73–0.76), and linolenic (r ²=0.67–0.74) acids could be used for sample screening. The SVM models produced significantly more accurate predictions than those developed with PLS. ANN calibrations were not different from the other two methods. Reduction in the number of calibration samples reduced predictive ability of all equations. The rate of performance degradation of SVM models with sample reduction was the lowest.     

Nanoscratch testing to assess the fiber adhesion of short‐carbon‐fiber composites

In a composite material, the degree of adhesion between the fiber and the matrix plays an important role in the overall performance of the material. Because the load between the fiber and the matrix is realized throughout the interphase region material, a lot of effort has gone into characterizing the strength of the interphase. In this study, nanoscratch tests on the composite samples were used to provide a relative measure of adhesion in different composite materials. Carbon‐filled nylon 6,6 and polycarbonate resins were evaluated with this method. The carbon fillers we used were polyacrylonitrile‐based carbon fibers sized and surface‐treated for the respective matrix and pitch‐based carbon fibers without any sizing or surface treatment. Tensile and X‐ray photoelectron spectroscopy data for the composites we considered are also presented to compare to the nanoscratch results. It is shown that nanoscratch testing on the composites, with the proposed data analysis, can be an effective tool for determining the relative degree of adhesion between different composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 328–335, 2007     

Preparation and characterization of PLLA/P(CL-b-LLA) blends by an in situ ring-opening polymerization

This paper describes a new reactive blending approach to improve the compatibility of poly(l-lactide) (PLLA) and poly(?-caprolacton) (PCL). For this purpose, the ring-opening polymerization of l-lactide (LLA) was carried out in the presence of PCL-OH (OH groups on one end). The P(CL-b-LLA) block copolymers were in situ formed during polymerization, and as a result, PLLA/P(CL-b-LLA) blends were obtained. The characterization of GPC and ¹H NMR verified the synthesis of PLLA/P(CL-b-LLA) blends. Furthermore, the ¹³C NMR spectroscopy showed that no transesterification reaction occurred to a significant extent during LLA polymerization process. The in situ formed P(CL-b-LLA) compatibilizes the phase separated structure of PCL domains in PLLA matrix. The size of PCL domains in PLLA matrix became much smaller than that in a solution blended sample. The average sizes of PCL domains are controllable in the level of sub-micron scale.     

The co-carbonization of oxidized coals with pitches and decacyclene

Coals of rank (NCB) 701, 401 and 204 were oxidized in air at 371 K for up to 15 days. The changes in optical texture of cokes from these coals were monitored by optical microscopy and point counting. The oxidized coals were cocarbonized to 1273 K with up to 30% of A240 petroleum pitch, a hydrogenated coal extract and decacyclene, and the resultant cokes were reassessed. The increase in isotropy in cokes caused by the oxidation treatment was never completely removed by use of the additives, but significant improvements existed for the less extensively oxidized coals. The possibility exists of using co-carbonization of oxidized coals with additives in coke making. Additives with good hydrogen donor ability, as with the coal extract, appear to be the most suitable.