An experimental study of an optical burst switching network based on wavelength-selective optical switches

In this article we report the system structure and test results of an experimental optical burst switching network with three edge router's and one core node. Wavelength-selective switches developed for this system and their characteristics are depicted. The implementation and performance of our new scheme for the just-in-time protocol are described. We also report experimental results of FTP and VOD services on this system. Some parameters, including traffic rate, average burst data length, and assembly time, are studied.     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.     

印染废水处理工艺研究及实例

本文简要介绍了印染废水水质特征,提出了处理工艺,并利用两个工程实例说明了该工艺的可行性.     

Stress analysis of spontaneous Sn whisker growth

Spontaneous Sn whisker growth is a surface relief phenomenon of creep, driven by a compressive stress gradient. No externally applied stress is required for the growth, and the compressive stress is generated within, from the chemical reaction between Sn and Cu to form the intermetallic compound Cu₆Sn₅ at room temperature. To obtain the compressive stress gradient, a break of the protective oxide on the Sn surface is required because the free surface of the break is stress-free. Thus, spontaneous Sn whisker growth is unique that stress relaxation accompanies stress generation. One of the whisker challenging issues in understanding and in finding effective methods to prevent spontaneous Sn whisker growth is to develop accelerated tests of whisker growth. Use of electromigration on short Sn stripes can facilitate this. The stress distribution around the vicinity and the root of a whisker can be obtained by using the micro-beam X-ray diffraction utilizing synchrotron radiation. A discussion of how to prevent spontaneous Sn whisker growth by blocking both stress generation and stress relaxation is given.     

Effect of boron on the low-cycle fatigue behavior and deformation structure of INCONEL 718 at 650 °C

Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on INCONEL 718 (IN718) containing 12, 29, 60, and 100 ppm B at 650 °C. The results showed that all the alloys experienced a relatively short period of initial cyclic hardening at low strain amplitudes, followed by a regime of saturation or slightly continuous cyclic softening. The initial cyclic hardening phase decreased with increasing strain amplitudes, and disappeared at the high strain amplitudes. A serrated flow was observed in the plastic regions of cyclic stress-strain hysteresis loops. The saturated cyclic stress amplitude at a given strain amplitude was highest for the alloy with 60 ppm B, and lowest for the alloy with 12 ppm B. The LCF lifetime increased with increasing B concentration up to 60 ppm, and then decreased as the B content increased from 60 to 100 ppm. Fractographic analysis suggested that the fracture mode changed from intergranular to transgranular cracking as the B concentration increased. The characteristic deformation microstructures produced by LCF tests at 650 °C, examined via transmission electron microscopy, were regularly spaced arrays of planar deformation bands on {111} slip planes in all four alloys. A ladderlike structure was observed in some local regions in the alloy with 12 ppm B. Heavily deformed planar deformation bands were observed in the fatigued specimens with 100 ppm B. The mechanism of improvement in the LCF life of IN718 due to B addition is discussed.     

Effects of Na, Cu, Ni and Co Modifications on the Activity and Characteristics of Rh/Al2O3 Catalysts for NO Reduction

This study used different metals to modify Rh/Al₂O₃ catalysts for NO reduction in a simulated waste incineration flue gas containing 6% O₂. The characteristics of the modified catalysts were analyzed using BET, TEM and XRD. The results of the experiment reveal that Na addition can significantly affect the properties of Rh/Al₂O₃ catalysts on the BET surface area and Rh metal dispersion. Furthermore, Na addition was found to significantly enhance the NO conversion of Rh/Al₂O₃ at 250–350 °C. On the contrary, Cu, Ni, and Co addition was found to have slight suppression effects.     

A Web-based Kanban system for job dispatching, tracking, and performance monitoring

A Kanban system facilitates lean principles in a simple and effective way. While reportedly successful in many manufacturing firms, the conventional Kanban systems using physical cards suffer from human errors, limited tracking capability, and so on. To make the information flow leaner, software providers add new features to their existing programs for manufacturing systems to computerize Kanban activities. As Web-based technologies advance rapidly, developing an entirely Web-based Kanban system appears to be feasible and promising. This paper presents the advantages, limitations, and challenges of Web-based Kanban systems. An experimental program has been developed based on PHP+MySQL, a popular Web programming platform. The server-executed program features cross-platform compatibility, real-time tracking and performance monitoring, and greatly enhanced information contents compared to physical Kanbans. Human errors are minimized by the automated transactions; nevertheless, the interfacing and data maintenance require further research efforts.