Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

Shear creep resistance of styrene–isoprene–styrene (SIS)‐based hot‐melt pressure‐sensitive adhesives

The effects of the properties of substrates and tackifier on the shear creep of SIS‐based HMPSAs were investigated. The holding power (t_b) and shear adhesion failure temperature (SAFT) were measured. The relationship between the complex viscosity and the holding power was examined. The holding power and SAFT values of the triblock SIS blends were higher than those of the diblock‐containing SIS blends, perhaps because blends using triblock SIS have higher crossover temperature and complex viscosity than those using diblock‐containing SIS. Higher levels of aromatic resin‐modified aliphatic tackifier and rosin ester were found to decrease the holding power of the HMPSAs. This maybe due to the fact that rosin ester and aromatic‐modified aliphatic resin are compatible with both the ends and midblocks of SIS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 825–831, 2006     

Preparation and barrier property of poly(ethylene terephthalate)/clay nanocomposite using clay‐supported catalyst

Poly(ethylene terephthalate) (PET)/clay nanocomposite was prepared by the direct polymerization with clay‐supported catalyst. The reaction degree of catalyst against the cation exchange capacity of clay was 8 wt %. The intercalation of PET chains into the silicate layers was revealed by X‐ray diffraction studies. SEM morphology of the nanocomposite showed a good dispersion of clay‐supported catalyst, ranging from 30 to 100 nm. The intercalated and exfoliated clay‐supported catalyst in PET matrix was also observed by TEM. The improvement of O₂ permeability for PET/clay‐supported catalyst composite films over the pure PET is approximately factors of 11.3–15.6. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4875–4879, 2006     

Surface characterization of 8‐quinolinyl acrylate‐grafted poly(ethylene terephthalate) prepared by plasma glow discharge and it's antibacterial activity

Poly(ethylene terephthalate) (PET) film was exposed to oxygen plasma glow discharge to produce peroxides on its surface. These peroxides were then used as catalysts for the polymerization of 8‐quinolinyl acrylate (QA) to prepare the PET grafted with QA (PET‐Q). The surface‐modified PET was characterized by attenuated total reflection Fourier transform infrared spectroscopy (ATR‐FTIR) and X‐ray photoelectron spectroscopy (XPS). The introduction of QA to the PET surface was confirmed by observing the presence of nitrogen in the XPS survey scan and high‐resolution spectra. The amount of QA grafted on to the PET surface as measured by the gravimetric method was about 5.2 μg cm^?2. The antibacterial activity of the surface‐modified PET texture was investigated by using a shake‐flask and an inhibition zone test method. After 6 h of shaking, the PET grafted with QA showed the inhibition (91%) of the growth of the gram‐positive microorganism, S. aureus. Even after laundering ten times, an effectiveness of the inhibition was found. However, little inhibition was shown with the gram‐negative microorganism, K. pneumoniae. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 863–868, 2006     

Curing behavior and structure of an epoxy/clay nanocomposite system

The curing behavior of an epoxy/clay nanocomposite system composed of a bifunctional epoxy resin with an aromatic amine curing agent and an organically modified clay was investigated. Differential scanning calorimetry (DSC) was used to investigate the curing behavior of the epoxy/clay nanocomposite system. The curing rate of the nanocomposite system increased with increasing clay content. A kinetic equation, considering an autocatalytic reaction mechanism, could describe fairly well the curing behavior of the epoxy/clay nanocomposite system. The reaction kinetic parameters of the kinetic equation were determined by fitting DSC conversion data to the kinetic equation, using a nonlinear numerical method. Dynamic mechanical analysis was used to investigate the thermomechanical properties of the epoxy/clay nanocomposite system. The glass transition temperature of the epoxy/clay nanocomposite system increased slightly with increasing clay content. The structure of the nanocomposite system was characterized by X‐ray diffraction analysis and transmission electron microscope imaging. The formation of intercalated structures was observed dominantly in the epoxy/clay nanocomposites, together with some exfoliated structures. POLYM. ENG. SCI., 46:1318–1325, 2006. © 2006 Society of Plastics Engineers     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Removal efficiencies of endocrine disrupting chemicals by coagulation/flocculation, ozonation, powdered/granular activated carbon adsorption, and chlorination

Removal efficiencies of endocrine disrupting chemicals (EDCs), bisphenol A and nonylphenol, during various types of water treatment processes were evaluated extensively using laboratory- and pilot-scale experiments. The specific processes of interest were coagulation/flocculation sedimentation/filtration (conventional water treatment process), powdered activated carbon (PAC), granular activated carbon (GAC), ozonation and chlorination. Batch sorption tests, coagulation tests, and ozone oxidation tests were also performed at higher concentrations with 14 EDCs including bisphenol A. The conventional water treatment process had very low removal efficiencies (0 to 7%) for all the EDCs except DEHP, DBP and DEP that were removed by 53%, 49%, and 46%, respectively. Ozonation at 1 mgO₃/ L removed 60% of bisphenol A and 89% of nonylphenol, while chlorination at 1 mg/L removed 58% and 5%, respectively. When ozone and chlorine doses were 4 and 5 mg/L, respectively, both EDCs were not detected. PAC removal efficiencies ranged from 15% to 40% at 3 to 10 mg/L of PAC with a contact time of 15 minutes. In the high concentration batch sorption tests, EDC removal efficiencies by PAC were closely related to octanol-water partition coefficient (K_ow). GAC adsorption was very effective water treatment process. The type and service time of GAC did not affect EDC removal efficiencies. The combination of ozonation and GAC in series appears to remove EDCs effectively to safe levels while conventional water treatment could not.     

The effect of zirconium oxide coating on the lithium nickel cobalt oxide for lithium secondary batteries

The electrochemical properties of LiNi_0.8Co_0.2O₂ coated with ZrO₂ by three different coating processes (ball-milling, sol-gel method, simple grinding) were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS). Results showed that the ZrO₂ coating significantly improved the capacity retention of the cathode by suppressing the impedance growth at the interface between electrodes and electrolyte and the best cyclability was obtained in the case of employing the simple grinding for the ZrO₂ coating. On the other hand, the initial capacities of the ZrO₂-coated LiNi_0.8Co_0.2O₂ cathode were slightly decreased.     

Poisoning effect of CO on ethylene polymerization with Ni(II)-diimine/MAO

CO was not a comonomer but an inhibitor in ethylene polymerization catalyzed over [1,2-bis(2,6-diisopropylphenylimino)]acenaphthene nickel(II) dibromide (1)/MAO. The average number of active sites, , and the average rate constant for chain propagation, of the (1)/MAO system was determined using CO inhibition method based on the assumption that two molecules of CO coordinate to each active center. At 0 °C, the average number of active centers, , was increased with the Al/Ni ratio, and , was not influenced by the Al/Ni ratio. Up to Al/Ni ratio of 3000, the average number of active sites was saturated. Single active site was present at the high ratio of Al/Ni and its reactivity with CO is uniform at 0 °C. The maximum average activity was 5262.07 (kg-PE/mol-Ni/atm/hr) and 65.7% of (1) was converted to form active cation complexes at 0 °C and Al/Ni molar ratio of 5000, while 36.5% of (1) was activated at the Al/Ni molar ratio of 250. Above 30 °C, the complicated CO poisoning behavior was observed because the reactivity and stoichiometry of active centers with CO were not uniform and their thermal stability was very poor.     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006