Oxygen-enrichment of YBa2Cu3 YBa2Cu3O7-δ using the fluidization techniqueusing the fluidization technique

The oxygen-deficient phase of the highT _c superconductor, YBa₂Cu₃O₇, was oxygen-enriched using the fluidization technique to give good superconducting properties. The normal method of oxygen treatment at 900°C for 24 h and at 600°C for 24 h has been reduced to just one treatment at 600°C for 12 h by the fluidization technique to achieve almost the same strength of superconducting signal for the YBa₂Cu₃O₇ powder, which establishes the attractiveness of the latter route for the large-scale preparation of superconducting material. The particle sizes were in the range 0–90, 90–180 and 180–420 μm. The fluidized particles were crystalline with orthorhombic distortion.T _c ^onset , estimated using the a.c. magnetic susceptibility method, was 91·3 K. The volume fraction of superconducting material in the product was 83·7–85·3%, one of the highest values reported so far for YBa₂Cu₃O₇.     

Spectrophotometric determination of some antioxidants with potassium permanganate and metol

New spectrophotometric methods for the assay of some antioxidants have been developed using potassium permanganate and metol (p-N-methyl amino phenol). Metol is oxidised at pH 3.0 with potassium permanganate and coupled with antioxidants to give λ_max at 560 nm for propyl gallate and gallic acid and 510nm for butylated hydroxy anisole. The method is simple, sensitive, reproducible and accurate within ±1% and applicable to the assay of antioxidants (gallic acid, propyl gallate and butylated hydroxy anisole) in oils and fats.     

Vinyl acetate monomer—a pilot plant study

The kinetics of the reaction of acetic acid and acetylene over zinc acetate-activated carbon catalyst was investigated over a wide range of process variables in a pilot reactor. Although various catalytic reaction mechanisms were postulated, the rate of reaction was most satisfactorily correlated by a mechanism of surface reaction between charged adsorbed acetic acid and acetylene, which assumes that the rate controlling step was the irreversible charged adsorption of acetylene and acetic acid.     

Investigations of surface characterization of silicone rubber due to tracking phenomena under a.c. and d.c. voltages

In the present work, tracking phenomena has been studied with silicone rubber material under the a.c. and d.c. voltages following IEC-587 standards. The surface condition of the tracked zone was analysed using wide angle X-ray diffraction (WAXD) and thermogravimetric differential thermal analysis (TG-DTA) studies. The tracking time was different for a.c. and d.c. voltages.     

Modeling of optical low coherence reflectometry recorded Braggreflectograms: evidence to a decisive role of Bragg spectral selectivity

This paper draws attention to the basic principles governing reflections in uniform Bragg reflectors (BR) when measured employing optical low coherence reflectometry (OLCR) technique. Using computations based on transfer matrix method (TMM), we first showed a strong spectral dependence of Bragg reflectograms on an OLCR probe spectrum. Later, this dependence is exploited to evaluate, for the first time, the coupling coefficient κ of a Bragg grating in a distributed Bragg reflector (DBR) laser on InP     

Thoria doped with cations of group VB–synthesis and sintering

The cations M⁵⁺ (M=V, Nb and Ta) were doped in thoria through gel-combustion synthesis using citric acid as fuel. Thorium dioxide feed powders thus prepared were cold compacted without binder or lubricant and sintered to a high density (9.5 Mg m⁻³) at relatively low temperatures (1623 K). The powders were characterised for the residual carbon, crystallite size, specific surface area, particle size distribution and bulk density. The distribution of the dopant in the thoria matrix was analyzed by electron probe microanalysis. The reactivity of the calcined powders was determined by measuring the density of the sintered compacts prepared from them. For the first time it is demonstrated that apart from niobia, even tantala and vanadia can bring about accelerated sintering in thoria if they are doped through a wet chemical route viz., the gel-combustion procedure. The maximum densities obtained by doping with vanadia (0.02 mol%), niobia (0.50 mol%) and tantala (0.50 mol%) were 9.8 Mg m⁻³ (1573 K), 9.68 Mg m⁻³ (1423 K) and 9.69 Mg m⁻³ (1623 K), respectively.     

Ion implantation doping of OMCVD grown GaN

Doping by ion implantation using Si, O, Mg, and Ca has been studied in single crystal semi-insulating and n-type GaN grown on a-sapphire substrates. The n-and p-type dopants used in this study are Si and O; Mg and Ca, respectively. Room temperature activation of Si and O donors has been achieved after 1150°C annealing for 120 s. The activation of Mg and Ca acceptors is too low to measure at both room temperature and 300°C. Using higher doses to achieve a measurable p-type conduction increases the amount of damage created by the implantation. Rutherford back scattering measurements on this material indicate that the damage is still present even after the maximum possible heat treatment. Secondary ion mass spectrometry measurements have indicated a redistribution in the measured profiles of Mg due to annealing.     

Ductile-phase toughening and Fatigue-Crack Growth in Nb-Reinforced Molybdenum Disilicide Intermetallic Composites

A study has been made of the role of ductile-phase toughening on the ambient temperature fracture toughness and fatigue-crack propagation behavior of a molybdenum disilicide intermetallicmatrix composite reinforced with 20 vol pct niobium spheres. Using disk-shaped compact DC(T) samples, only moderate improvements (∼24 pct) in fracture toughnessK _lcvalues were found for the composite compared to the unreinforced MoSi₂ matrix material. Moreover, (cyclic) fatigue- crack propagation was seen at stress intensities as low as 75 to 90 pct ofK _Ic, with growth rates displaying a high dependency (∼14) on the applied stress-intensity range. The lack of significant toughening due to the incorporation of ductile Nb particles is associated with an absence of crack/particle interactions. This is attributed to the formation of a weak reaction-layer interface and elastic mismatch stresses at the crack tip between the Nb and MoSi₂, both factors which favor interfacial debonding; moreover, the spherical morphology of Nb phase stabilizes cracking around the particle. Results suggest that increasing the aspect ratio of the distributed Nb rein- forcement phase with attendant interfacial debonding and eliminating possible Nb-phase em- brittlement due to interstitial impurity contamination are critical factors for the successful development of tougher Nb/MoSi₂ structural composites. Formerly with McDonnell Formerly with McDonnell