Investigation on Convective Drying of Mixtures of Sewage Sludge and Sawdust in a Fixed Bed

This work is part of a project aiming to develop a renewable fuel for gasification purposes, through convective drying of sludge/wood mixtures. The first step consists of characterizing the behavior of sawdust/sludge mixtures during the application of convective drying. The influence of the mixing step (no mixing versus 30 s at 40 rpm), as well as the sawdust : sludge ratio (1:9, 2:8, 3:7, and 4:6 on a dry basis) and the effect of drying temperature (50, 80, and 110°C) were investigated. In this study, X-ray tomography, a noninvasive imaging technique, is used to assess changes in the volume, void, and exchange surface at the beginning and the end of the drying process. Results first confirm the importance of the mixing step on the drying behavior: the drying rate of the mixed sludge is lower than that of the original sludge. Nevertheless, the addition of sawdust is shown to have a positive impact on the drying process from a mass ratio of 2:8, with drying rates higher than that of the original sludge. With increasing amounts of sawdust, the initial and final bed volumes, initial and final total exchange surfaces, and initial void fraction increase linearly, but the bed volume shrinkage and final void fraction decrease linearly.     

Structure and Reactivity of Spruce Mechanical Pulp Lignins Part I. Bleaching and Photoyellowing of in situ Lignins

This paper reports the structural investigation of a series of in situ spruce lignins in wood, thermomechanical pulp (TMP) and the corresponding bleached (BTMP) and photoyellowed (YBTMP) samples. This was achieved by using an original two-step degradative technique, thioacidolysis followed by Raney nickel desulfuration. The determination of thioacidolysis monomeric and dimeric products allowed an estimate of various lignin building units and interunit bonds, respectively. It was observed that the thermomechanical and bleaching treatments did not affect spruce lignin structure to an appreciable extent. On the contrary, the photoyellowing treatment caused marked structural changes in lignin, particularly when run in severe conditions. These changes were essentially a decrease in the amount of β-O-4 and β-1 interunit bonds and a relative increase in catechol units and in vanillin end-groups.     

Ruthenium‐Catalyzed One‐Pot Tandem Isomerization–Transfer Hydrogenation Reactions of γ‐Trifluoromethylated Allylic Alcohols and β‐Trifluoromethylated Enones

The ruthenium–2‐propanol combination was found to transform γ‐trifluoromethylated allylic alcohols and β‐trifluoromethylated enones into the corresponding saturated alcohols in excellent yields via a one‐pot tandem process involving isomerization and transfer hydrogenation(s). High stereospecificity was demonstrated and evidence for two mechanistic pathways is provided. The method was applied to a rapid synthesis of trifluoromethylated citronellol.     

Application of a New Method for Radiative Heat Transfer to Flat Glass Tempering

Temperature distributions within semi-transparent materials like glass strongly determine their behavior. It is fundamental to take radiation into account to determine exact temperature distributions. The Rosseland Approximation for radiation is usually an appropriate method, but is only valid with an optically thick glass. In the present paper, we propose an improved approximation that is both efficient and sufficiently accurate even for the semi-transparent region. This new radiation model is used to determine the temperature along the flat glass thickness during tempering. The impact of temperature evaluation on residual stresses is discussed.     

A concept of reactive compatibilizer‐tracer for studying reactive polymer blending processes

A concept called reactive compatibilizer‐tracer is proposed. The latter bears reactive groups capable of reacting with its counterpart on forming a copolymer for in situ compatibilization, and fluorescent labels allowing determining very small amounts of the in situ formed compatibilizer and formation of micelles when it occurs. Owing to this concept, it is shown that a reactive compatibilizer may be very efficient at the beginning of a reactive blending process and may suddenly become completely inefficient, resulting in an abrupt and drastic increase in size of the dispersed phase domains. © 2015 American Institute of Chemical Engineers AIChE J, 62: 359–366, 2016     

Treatment of olive mill washing water by ultrafiltration

Olive oil production requires important quantities of washing water containing low oil concentrations, but classical processes used to recover or to eliminate this oil are ineffective. This study presents a membrane technique to treat olive oil mill washing water using different commercial ultrafiltration membranes: one organic (PCI) and two ceramic (Ceraver) membranes. The influence of the hydrodynamic parameters (transmembrane pressure and flow rate) and the cut‐off membranes on the efficiency of the ultrafiltration process was evaluated, and it was shown the organic PCI membrane could reduce pollution due to organic matter by decreasing the value of the Chemical oxygen demand by about 90%. Moreover, the nature of the ultrafine pore membrane appeared to be an important parameter which may strongly increase or decrease the capacity of the membrane. The membrane cut‐off did not have a strong influence on the performance of the process but if the membrane pores were too large the stability of the dynamically formed membrane decreased at transmembrane pressures greater than 0.2 MPa.     

Microstructural characterization of creep anisotropy at 673 K in the M5® alloy

Zirconium alloy tubing is used in pressurized water nuclear reactors in order to prevent fissile material from leaking into the coolant. It can be the first safety wall of nuclear fuel, and is submitted to complex thermomechanical loadings. In consequence, new Nb-modified alloys, such as the M5® alloy, and fine numerical models are being developed to guarantee a better and longer mechanical integrity of these tubes. To identify the physical mechanisms that could be considered in such models, an experimental approach, combining creep tests with electron backscattered diffraction and Transmission electron microscopy investigations, was carried out.Tubular specimens were submitted to multiaxial creep tests at a temperature of 673 K. Seven ratios between the axial and hoop applied stresses were investigated. It enabled a macroscopic evidence of the creep anisotropy. Besides, EBSD analyses on a mesoscopic-sized non deformed area led to the characterization of the variation of the average Schmid factor with the direction of loading. Finally, TEM observations were done on seven crept samples, corresponding to the seven directions of loading tested mechanically. The variations of the different parameters investigated (activated slip systems, dislocation densities, curvatures of the dislocations) can be seen as the effects of the creep anisotropy at a microscopic scale. The correlation between results is then discussed in a multiscale frame.     

Potential influence of microorganisms on the corrosion of carbon steel in the French high- and intermediate-level long-lived radioactive waste disposal context

In the context of the high-level radioactive waste disposal CIGEO, the corrosion rate due to microbially influenced corrosion (MIC) has to be evaluated. In France, it is envisaged to dispose of high- and intermediate-level long-lived radioactive waste at a depth of 500 m in a deep geological disposal, drilled in the Callovo-Oxfordian claystone (Cox) formation. To do so, a carbon steel casing will be inserted inside disposal cells, which are horizontal tunnels drilled in the Cox. A specific cement grout will be injected between the carbon steel casing and the claystone. A study was conducted to evaluate the possibility of MIC on carbon steel in the foreseeable high radioactive waste disposal. The corrosiveness of various environments was investigated at 50°C and 80°C with or without microorganisms enriched from samples of Andra's underground research laboratory. The monitoring of corrosion during the experiments was ensured using gravimetric method and real-time corrosion monitoring using sensors based on the measurements of the electrical resistance. The corrosion data were completed with microbiological analyses including cultural and molecular characterizations.     

Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

Engineering HVOF-Sprayed Cr3C2-NiCr Coatings: The Effect of Particle Morphology and Spraying Parameters on the Microstructure, Properties, and High Temperature Wear Performance

Chromium carbide-based thermally sprayed coatings are widely used for high temperature wear applications (typical temperature range from 540 to 900 °C). In these extreme environments at those temperatures, several phenomena will degrade, oxidize, and change the microstructure of the coatings, thereby affecting their wear behavior. Although it can be easily conceived that the Cr₃C₂-NiCr coating microstructure evolution after high temperature exposure will depend on the as-sprayed microstructure and spraying parameters, very little has been done in this regard. This study intends to develop a better understanding of the effect of spraying parameters on the resulting chromium carbide coating microstructure after high temperature operation and high temperature sliding wear properties. The microstructures of different coatings produced from two morphologies of Cr₃C₂-NiCr powders and under a window of in-flight particle temperature and velocity values were characterized through x-ray diffraction and scanning electron microscopy. Sliding wear at 800 °C was performed and the wear behavior correlated with the spraying parameters and coating microstructure. Vickers microhardness (300 gf) of the coatings before and after sliding wear was also measured.