FLUID COKING is a continuous process that thermally converts heavy hydrocarbons, such as oil sands bitumen, to lighter and higher‐value products by horizontal spray injection onto a fluidized bed of hot coke particles. The cyclone sections of commercial fluid coker reactors experience fouling during typical operation, which limits unit run lengths. The main objective of this work is to improve fluid coker reliability by proposing cyclone fouling mitigation strategies based on practical operation modifications. This study developed a process simulation in Aspen Plus to establish the combined impact of vapour‐liquid equilibrium, endothermic thermal cracking reactions, pressure changes, and overall fluid dynamics in the selected fluid coker control volumes. The hydrocarbon composition was defined by applying an assay characterization of distillation data for representative hydrocarbon streams. Case studies were performed to determine the sensitivity of the predicted temperatures and hydrocarbon condensate flow rates for: (a) the burner‐to‐fluid coker transfer line temperature; (b) the hot coke flow rate; (c) hot coke entrainment from the freeboard region; and (d) scouring coke flow rate in the horn chamber. The scouring coke flow rate was identified as the most promising process lever to mitigate fluid coker cyclone fouling. 相似文献
In this work, PVDF composites containing 0.2% (m/m) of carbon nanotubes (MWCNTs), PVDF with 5.0% (m/m) of zinc oxide (ZnO), and composites containing both particles in the same contents in the matrix were melt processed in a mini-extruder machine with double screws, using the counter-rotation mode. Composites were characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), dynamic-mechanical analysis (DMA), and contact angle tests (CA). The samples presented the predominance of the α phase, with an increased degree of crystallinity as well as an increase in dimensional stability by incorporating both fillers, showing a synergistic effect between these particles, as shown on FTIR, DSC, and XRD results. SEM images showed a good dispersion of high aspect ratio particles. In general, DMA and TGA analysis showed that composites had not decreased their thermal and mechanical performance when compared to neat PVDF. Results of CA analysis showed an increase in the hydrophobicity of the sample containing MWCNTs. Permeability tests were also performed using a differential pressure system, combining high temperature and pressure, obtaining permeability measures and time lag. This work presents an alternative of composite materials, suggesting its application in the internal pressure sheath layers of oil and gas flexible pipes. 相似文献
In response to herbivory, plants emit volatile compounds that play important roles in plant defense. Herbivore-induced plant volatiles (HIPVs) can deter herbivores, recruit natural enemies, and warn other plants of possible herbivore attack. Following HIPV detection, neighboring plants often respond by enhancing their anti-herbivore defenses, but a recent study found that herbivores can manipulate HIPV-interplant communication for their own benefit and suppress defenses in neighboring plants. Herbivores induce species-specific blends of HIPVs and how these different blends affect the specificity of plant defense responses remains unclear. Here we assessed how HIPVs from zucchini plants (Cucurbita pepo) challenged with different herbivore species affect resistance in neighboring plants. Volatile “emitter” plants were damaged by one of three herbivore species: saltmarsh caterpillars (Estigmene acrea), squash bugs (Anasa tristis), or striped cucumber beetles (Acalymma vittatum), or were left as undamaged controls. Neighboring “receiver” plants were exposed to HIPVs or control volatiles and then challenged by the associated herbivore species. As measures of plant resistance, we quantified herbivore feeding damage and defense-related phytohormones in receivers. We found that the three herbivore species induced different HIPV blends from squash plants. HIPVs induced by saltmarsh caterpillars suppressed defenses in receivers, leading to greater herbivory and lower defense induction compared to controls. In contrast, HIPVs induced by cucumber beetles and squash bugs did not affect plant resistance to subsequent herbivory in receivers. Our study shows that herbivore species identity affects volatile-mediated interplant communication in zucchini, revealing a new example of herbivore defense suppression through volatile cues.
A mechanism of formation of copper nanoparticles is proposed for alkaline etching of a sputtering-deposited Al-30 at.%Cu alloy, simulating the equilibrium θ phase of 2000 series aluminium alloys. Their formation involves enrichment of copper in the alloy beneath a thin alumina film, clustering of copper atoms, and occlusion of the clusters, due to growth of alumina around the clusters, to form nanoparticles. The proposed mechanism is supported by medium energy ion scattering, Rutherford backscattering spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy of the alloy following immersion in the sodium hydroxide solution, which disclose the enrichment of copper and the generation of the nanoparticles in the etching product of hydrated alumina. The generation of the nanoparticles is dependent upon the enrichment of copper in the alloy in a layer of a few nanometres thickness, with no requirement for bulk de-alloying of the alloy. 相似文献
The effect of copper content (0.01 and 2.1%) and microstructure on the intrinsic hydrogen embrittlement susceptibility of unl nercially-processed AI---6Zn---2Mg---XCu alloys was investigated. (The alloy with 2.1 Cu corresponds to 7059). Hydrogen was introduced into the alloys using cathodic charging, both with and without concurrent plastic straining. The copper-free alloy in both the under-aged and peak-aged conditions was embrittled by hydrogen and the effect was enhanced by concurrent plastic strain. The copper-containing alloy (7050) was susceptible to hydrogen embrittlement when under-aged, but once the peak-strength microstructure had been developed, the alloy in the longitudinal direction showed no embrittlement even under severe hydrogen-entry conditions. Similar beneficial effects have been reported for copper additions in imparting resistance to humid air and stress-corrosion cracking for high strength AI-Zn-Mg alloys, and the results are discussed with emphasis on the parallel nature of the phenomena of stress-corrosion cracking and hydrogen embrittlement. 相似文献
Anodizing of solid-solution Al-1at.%Cu alloy in ammonium pentaborate electrolyte is shown to develop two distinct types of amorphous film. On alloy grains of {1 0 0} orientation, the alumina film is of uniform thickness and relatively featureless. For other grains, the film is of non-uniform thickness and contains oxygen bubbles. In both cases, copper species are distributed throughout the film. Copper is enriched in the alloy to ∼5.8×1015 Cu atoms cm−2 for bubble-free grains, with similar or slightly lower levels for other grains. Evidently, copper enrichment alone does not lead to generation of oxygen. Other factors suggested to be involved, each dependent upon grain orientation, are the structure of the enriched alloy layer, the cyclic nature of the oxidation of copper, and the generation of modulated film compositions. 相似文献
The initial stages of oxide growth on titanium are examined in a recently developed commercial alkaline pyrophosphate/aluminate electrolyte of interest for plasma electrolytic oxidation of light metal alloys. Constant current anodizing was employed, with resultant films examined by scanning and transmission electron microscopies and Rutherford backscattering spectroscopy. The initial film is relatively uniform and composed of TiO2, with low concentrations of aluminium and phosphorus species incorporated from the electrolyte. With increase in voltage the film breaks down locally, and regions of original and modified film develop simultaneously, with the latter occupying more of the surface as the voltage rises. Porous regions due to dielectric breakdown also become increasingly evident. At 240 V, sparking commences, and the surface reveals extensive, relatively uniform porosity, with the coating now containing much enhanced concentrations of aluminium and phosphorus species compared with the coating at lower voltages. The films develop at low efficiency due to generation of oxygen. The oxygen is produced within the original film material and at sites of dielectric breakdown. The former type of film develops a two-layered morphology, with an outer layer of amorphous TiO2 and an inner layer with numerous fine and course cavities. The cavities are due to the generation of oxygen that may be associated with the formation of anatase in the inner layer. 相似文献
This study examined the influences of website design on prospective job seekers. A total of 182 participants accessed and reviewed an online job ad. Afterwards, they rated: (a) the attractiveness of the ad’s formatting, (b) the usability of the website, (c) overall evaluations of the organization’s web appeal, (d) impressions of the organization, and (e) willingness to pursue employment with the hiring organization. Although both the formatting attractiveness and usability of online recruitment materials influenced participants’ inclinations to pursue jobs, formatting was more important than usability. Moreover, impressions of the employer mediated the relationship between satisfaction with the website and willingness to pursue employment with the organization. Overall, this research advances knowledge by applying signaling theory to the web-based recruitment domain and by testing a mediated relationship implied therein. In addition, this is the first study to introduce relative weights analysis to the recruitment literature. 相似文献
We describe the design, construction, and performance of three generations of superconducting Ioffe magnetic traps. The first two are low current traps, built from four racetrack shaped quadrupole coils and two solenoid assemblies. Coils are wet wound with multifilament NbTi superconducting wires embedded in epoxy matrices. The magnet bore diameters are 51 and 105 mm with identical trap depths of 1.0 T at their operating currents and at 4.2 K. A third trap uses a high current accelerator-type quadrupole magnet and two low current solenoids. This trap has a bore diameter of 140 mm and tested trap depth of 2.8 T. Both low current traps show signs of excessive training. The high current hybrid trap, on the other hand, exhibits good training behavior and is amenable to quench protection. 相似文献
Proof planning is a technique for theorem proving which replaces the ultra-efficient but blind search of classical theorem proving systems by an informed knowledge-based planning process that employs mathematical knowledge at a human-oriented level of abstraction. Standard proof planning uses methods as operators and control rules to find an abstract proof plan which can be expanded (using tactics) down to the level of the underlying logic calculus.In this paper, we propose more flexible refinements and a modification of the proof planner with an additional strategic level of control above the previous proof planning control. This strategic control guides the cooperation of the problem solving strategies by meta-reasoning.We present a general framework for proof planning with multiple strategies and describe its implementation in the Multi system. The benefits are illustrated by several large case studies, which significantly push the limits of what can be achieved by a machine today. 相似文献