Osteoblast behavior on TiO2 microgrooves prepared by soft-lithography and sol–gel methods

This study focused on the effects of microgrooved TiO₂ surfaces on osteoblast behavior. Microgrooved TiO₂ surfaces with different widths (12 μm and 40 μm) and flat surfaces were fabricated on glass substrates based on the combination of a sol–gel technique and soft-lithography. Osteoblasts (MC3T3-E1) were cultured on the as-prepared microgrooved and flat TiO₂ surfaces. Optical microscopy and scanning electron microscopy were used to analyze the adherent cell behavior by examining the cell morphology. Orientation angle analysis indicated that the cells tended to align along the microgrooves. This tendency was stronger on the microgrooves with smaller widths and became weak with increasing width. Alamar Blue assay indicated that the microgrooves restricted cell proliferation and the alkaline phosphatase assay revealed that the microgrooves limited the differentiation rate. This restriction increased with decreasing microgroove width. The surface energy of the TiO₂ surfaces was size-dependent and followed the order γ _12 μm < γ _40 μm < γ _{flat surfaces}. Osteoblast proliferation and differentiation on the surface with high surface energy exhibited high proliferation and differentiation rates. These results indicated that surface energy appeared to be a dominant factor for cell activity. Thus, surface energy would be a valuable index for the cell compatibility of a micropatterned surface.     

Effects of functional groups in glow discharge polymerization

Summary Glow discharge polymerizations of allyltrimethylsilane (ATMS) and trimethylvinyloxysilane (TMVOS) were investigated by elemental analysis and infrared spectroscopy. The formed polymers were far different in elemental composition from the starting materials, and possessed high carbon and hydrogen contents. There was less difference in an infrared-spectral sense between the two polymers from ATMS and TMVOS. A polymer-forming process in a discharge state is discussed.     

Surface modification of tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) by plasmas for copper metallization

Tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) sheet surfaces were modified with argon, helium, oxygen, and hydrogen plasmas. How the four plasmas modified the PFA sheet surfaces was investigated. All plasmas modified the PFA surfaces and at the same time initiated degradation of the PFA polymer chains. The balance between modification and degradation was strongly influenced by the magnitude of the discharge current in the plasmas. Efficiency of the plasmas in modification was hydrogen plasma > oxygen plasma > argon plasma > helium plasma. The modification involved defluorination of CF₂ carbons into CHF and CH₂ carbons and oxidation into O? CH₂, O? CHF, and O? CF₂ groups. The surface‐modification technique (a combination of hydrogen plasma treatment and silane coupling treatment) proposed in this study was applied for copper metallization of the PFA surface. The utility of the technique was confirmed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1087–1097, 2002     

Crack growth characteristics of carbon nanotube-based polymer composites subjected to cyclic loading

This paper presents the characterization of crack growth in carbon nanotube (CNT)-based polymer composites under fatigue loading. Fatigue crack growth tests were performed on single-edge cracked plate specimens of CNT/polycarbonate composites at room temperature and liquid nitrogen temperature (77 K). An elastic–plastic finite element analysis was also conducted to determine the J-integral range. The crack growth rate data were expressed in terms of the J-integral range, and the effect of nanotube addition on the fatigue crack growth behavior was examined. In addition, possible mechanisms of the crack growth in the nanocomposites are discussed based on microscopic observations of the specimen fracture surfaces.     

Optimization of human interface configurations and safety control policies for alarm subsystems

This paper gives four alarm subsystems with different human interface configurations which include fault-alerting and safety-presentation types, where two kinds of correspondences between sensor states and plant states are distinguished. For each configuration, we give probabilistic analyses on occurrence of spurious-shutdowns (SS) and hazardous-accidents (HA). We prove that either the fault-alerting alarm subsystem or the safety-presentation alarm subsystem can be an optimal alarm subsystem which minimizes SS and HA failure probabilities simultaneously if we choose a human interface configuration and its associated safety-control policy in an appropriate manner.     

Temperature distribution in Li2O pellets under neutron irradiation

The center temperature of Li₂O pellets under neutron irradiation was measured using an encapsuled pin. The surface temperatures of the pellets and the pellet/cladding heat transfer coefficients were estimated on the basis of the well-known conductivity integral.     

Accuracy of measurements of the quantized Hall resistivity by adirect current comparator type potentiometer: calibration using aJosephson potentiometer

The accuracy of measurements of the quantized Hall resistivity (QHR) by a direct-current-comparator (DCC)-type potentiometer is estimated based on a linearity calibration of the potentiometer using a Josephson potentiometer. The power coefficient contribution to the nonlinearity of the DCC potentiometer was found to be 0.15±0.02 p.p.m./(100 mV)² at 18.5±0.5°C in 1985 and 0.21±0.03 p.p.m./(100 mV)² at 20.5±0.5°C in 1988. The possibility of accurate measurements of the ratio QHR/R _STD with uncertainties less than 0.05 p.p.m. by the DCC potentiometer is discussed     

Fracture Energy of an Aligned Porous Silicon Nitride

The fracture energy of a porous silicon nitride with aligned fibrous grains was investigated, using a chevron-notched-beam technique. A crack was constrained to propagate normal to the grain alignment. The obtained fracture energy was ∼500 J/m², which was ∼7 times larger than that of a dense silicon nitride with randomly oriented fibrous grains. The large fracture energy was attributable primarily to the sliding resistance associated with interlocking grains.     

Mechanochemical solid-phase reaction between polyvinylidene fluoride and sodium hydroxide

Grinding a mixture of polyvinylidene fluoride (PVDF) and NaOH was conducted by a planetary ball mill at atmospheric condition to investigate mechanochemical reaction between the two substances. The grinding stimulates the reaction to form NaF and organic composites. Yield of fluorine converted from PVDF to NaF increases with an increase in grinding time and reaches 90% at 60 min or more. As for the organic phase, oxygen-bearing compounds are formed due to substitution of fluorine by OH base. The organic compounds are classified into water-soluble and insoluble ones, depending on their structures. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2249–2252, 2001     

HD/SHD still image database system and image distribution in broadband network applications

This paper focuses on a practical design for an efficient scalable image database and retrieval system over broadband networks. It describes a concrete solution for the implementation of HD/SHD (high-definition/super-high-definition) still image retrieval services which can be used in different applications. The structure of the complete system, consisting of a directory server, an image server, and MMI (man-machine interface) devices, has been presented, detailing each element and their corresponding functions. The desired HD/SHD image is displayed on the HD-PDP (plasma display panel) with the aid of image matching. The proposed system generates image index automatically, eliminating special skills in preparing index images and crucially reducing the processing time (from 35 min to 110 s), and does not use keywords. It has been also shown that these indices can be used for quite accurate image retrieval, i.e., the system provides high precision rates (currently up to 98%) to the user, eliminating troubles encountered in the image retrieval operations due to limitation on the user’s age, culture, knowledge, and languages.The broadband IP networks currently have a number of issues from the viewpoint of practical system operations, and so the requirements and issues needed for the networks are discussed from the viewpoint of in-service performance, differentiation among different types of services, secure connections, and so on, focusing on handling of HD/SHD still images.