Defects in offsite construction: timber module prefabrication

The construction industry is based on craftsmanship. Quality control and assurance procedures applied in manufacturing cannot usually be readily applied in construction, where there are higher degrees of uniqueness in each project. One category of companies, industrialized housebuilders, is attempting to bridge some of the gaps between construction and manufacturing. These companies prefabricate building modules for later assembly at the building site. Since they are wholly responsible for large parts of the building process, these companies have greater opportunities to control and improve quality in a more consistent way than ordinary construction companies. Thus, it could be hypothesized that the frequency and severity of defects should be lower in industrialized housing than in ordinary construction. The aim of the study presented here is to examine this hypothesis by measuring and characterizing defects in industrialized housing. The design and manufacturing processes at two Swedish timber module prefabrication firms has been analysed through interviews, site visits and document reviews. Quality audits from three phases of the building process were compiled, analysed and categorized to provide statistical measures of defects in industrialized housing. The results show that the case study companies are better in terms of product quality than conventional housing.     

A study of a plan-do-check-act method used in less industrialized activities: two cases from industrialized housebuilding

In construction projects, a large number of deviations are usually found during inspections and adjusted in a reactive manner. For projects to become proactive, root causes need to be identified and eliminated as a part of a process of continuous improvement (CI). Plan-do-check-act (PDCA) methods are part of CI and have been used with success within the manufacturing industry for decades. Research studies of PDCA in construction are less common, which could be explained by the past dominance of the project-based nature of construction compared to the process-based nature of manufacture. Industrialized construction, however, has changed this picture somewhat, and it is of interest to find out how well it works for less industrialized activities in construction. A PDCA method was tested in two cases selected from one medium-sized Swedish industrialized housebuilder, which uses a building system based on offsite manufactured modules. Empirical results are based on systematic data gathered through interviews and participant observations. Results from the two cases show that the PDCA method worked even when processes were divided into industrialized parts within a factory and non-industrial parts at the construction site although this might lead to temporary corrective actions rather than permanent process actions.     

Approximate analytical solutions to the condensation-coagulation equation of aerosols

We present analytical solutions to the steady state nucleation-condensation-coagulation equation of aerosols in the atmosphere. These solutions are appropriate under different limits but more general than previously derived analytical solutions. For example, we provide an analytic solution to the coagulation limit plus a condensation correction. Our solutions are then compared with numerical results. We show that the solutions can be used to estimate the sensitivity of the cloud condensation nuclei number density to the nucleation rate of small condensation nuclei and to changes in the formation rate of sulfuric acid.

© 2016 American Association for Aerosol Research     

The use of (green field) biomass pretreatment liquor for fermentative butanol production and the catalytic oxidation of biobutanol

In this study, pretreatment liquor of acid-stored green and yellowish barley silage was used for fermentative acetone–butanol–ethanol (ABE) production. Further, the catalytic oxidation of biobutanol over Pt catalysts was studied to investigate the behaviour of butanol as a fuel in the combustion engine. After the hydrothermal treatment of green and yellowish barley silage followed by enzymatic hydrolysis, approximately 88% and 100% of the available sugars were recovered, respectively. Batch fermentations of pretreatment barley silage liquor, supplemented with gelatinised barley grain, showed good fermentability with total ABE concentrations of 9.0 g/L and 10.9 g/L. Butanol yields of 0.20, 0.17 and ABE yields of 0.28, 0.26 (g/g monosaccharide) were obtained, respectively. In catalytic activity measurements, the conversion of biobutanol became appreciable in the 120–140 °C range, whereas conversions greater than 95% were obtained over 200 °C. Selectivities were also high, although formation of by-products, such as butyraldehyde, was observed.     

Development of nanocomposites based on organically modified montmorillonite and plasticized PVC with improved barrier properties

Montmorillonite (MMT) was organically modified with tributyl citrate (TBC). Organoclays (OMMTs) were processed with diisononyl phthalate (DINP)‐plasticized polyvinyl chloride (PVC) to form polymer nanocomposites. The produced composite materials showed a contradictory change in properties to that expected of a layered silicate nanocomposite, with a decreased E‐modulus and increased gas permeability compared with a material without OMMT. It was experimentally shown that the TBC modifier was extracted from the OMMT and was dispersed in the PVC/DINP matrix, whereupon the OMMT collapsed and formed micrometer‐sized agglomerates. Further investigation revealed that TBC has a significant effect on the gas permeability and the E‐modulus, even at low additions to a DINP‐plasticized PVC. A PVC nanocomposite with the TBC acting as both the OM for MMT and as the primary plasticizer was produced. This material showed a significantly increased E‐modulus as well as a decrease in gas permeability, confirming that it is possible to develop a nanocomposite based on plasticized PVC, if both the organo‐modification of the MMT and the formulation of the matrix are carefully selected. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42876.     

A Model for Through Drying of Tissue Paper at Constant Pressure Drop and High Drying Intensity

A mathematical model for through drying of paper at constant pressure drop was developed. The model is based on physical properties; hence, basis weight, pressure drop, drying air temperature, pore size distribution, initial gas fraction, and tortuosity are important input parameters to the model. The model was solved for different combinations of the variables basis weight, drying air temperature, and pressure drop corresponding to industrial conditions and the results were compared with data from bench-scale experiments. The simulations show that the drying rate curve is very sensitive to the air flow rate and that correctly modeling the correlation between pressure drop and air flow rate is the most important factor for a successful model for through drying. The model was tuned by adjusting the parameters initial gas fraction and tortuosity in order to give the best possible fit to experimental data. For a given basis weight and pressure drop, different drying air temperatures resulted in relatively constant values of the fitted parameters. This means that the model can well predict the effects of changes in drying air temperature based on a tuning of the model performed at the same basis weight and pressure drop. However, for a given basis weight, an increase in pressure drop yielded fitted parameters that were somewhat different; i.e., a lower initial gas fraction and a higher tortuosity, a change that increases the resistance to air flow. This implies that the correlation between pressure drop and air flow rate in the model does not quite capture the nonlinear relationship shown by the experiments.