Comparative study of the buckling of steel beams in Eurocode 3 and the Russian code

Lateral torsional buckling is the main limit state that must be checked for steel beams. Design codes provide different models for the analysis of this complex phenomenon. The present paper describes a comparative study of the interpretation of beam buckling of symmetrical sections in EN 1993-1-1 (EC3), its preliminary ENV-version and a Russian steel structure design code. In order to choose the nationally determined parameters in EC3, the impact of parameters on the safety level and overall design results has to be carefully studied. Modification factors, introduced in EC3, have moved the resistance for certain load distribution from ENV-based values closer to the Russian code.     

Finite-Element Simulations of Cracks Near Interfaces: Effects of Thermal, Elastic, and Plastic Mismatch

Cracks situated parallel to, and very near, the interface in layered, ductile-brittle composite specimens were investigated with finite-element analysis. Elastic, plastic and thermal properties previously obtained from experiments were utilized in the model. A routine was employed for automatic crack extension and remeshing, enabling simulation of incremental crack propagation. The elastic, thermal and plastic contributions to crack propagation behavior were investigated, along with the variation of these with crack length and crack-tip position. Thermal residual stresses are shown to have a large influence on crack path, although this is mitigated to some extent by plasticity. The implications on the inherent reliability of joints and layered materials containing brittle constituents are discussed.     

Two-phase modeling of mushy zone parameters associated with hot tearing

A two-phase continuum model for an isotropic mushy zone is presented. The model is based upon the general volume-averaged conservation equations, and quantities associated with hot tearing are included, i.e., after-feeding of the liquid melt due to solidification shrinkage is taken into account as well as thermally induced deformation of the solid phase. The model is implemented numerically for a one-dimensional model problem with some similarities to the aluminium direct chill (DC) casting process. The variation of some key parameters that are known to influence the hot-tearing tendency is then studied. The results indicate that both liquid pressure drop due to feeding difficulties and tensile stress caused by thermal contraction of the solid phase are necessary for the formation of hot tears. Based upon results from the one-dimensional model, it is furthermore concluded that none of the hot-tearing criteria suggested in the literature are able to predict the variation in hot-tearing susceptibility resulting from a variation in all of the following parameters: solidification interval, cooling contraction of the solid phase, casting speed, and liquid fraction at coherency.     

敏捷到底是什么？

在支持软件工程(比如Rational统一过程RUP)与敏捷阵营(比如SCRUM或是XP)之间,人们一直存在着冲突。也不难理解,因为这两种方法间都是在用着彼此并不兼容的方式来描述的。其实大可不必,因为他们背后的观点全然是相辅相成的。关键在于该如何用对两者来说都公平的方式来融合它们。在软件世界里,我们都喜欢跟风。我     

Effect of domperidone on the health-related quality of life of patients with symptoms of diabetic gastroparesis

OBJECTIVE: To describe the health-related quality of life (HRQOL) of patients with insulin-treated diabetes and symptoms of diabetic gastroparesis and to assess the impact of domperidone on HRQOL in these patients. RESEARCH DESIGN AND METHODS: This two-phase multicenter study was part of a safety and efficacy investigation. Phase I involved 4-week single-blind treatment with domperidone 20 mg q.i.d. (n=269). Patients demonstrating significant symptomatic improvement (n=208) continued to phase 11, a 4-week, double-blind, parallel-group study with patients receiving placebo (n=103) or domperidone (n=105). Patients completed the Medical Outcomes Study Short-Form-36 Health Survey at selection and at the end of each phase. Physical component summary (PCS) and mental component summary (MCS) scores served as primary parameters, and the eight subscales were secondary parameters. RESULTS: HRQOL scores of subjects enrolled in the trial were significantly lower than norms from the general population and people with diabetes (P < 0.001). Subjects experiencing symptomatic improvement after 4 weeks of single-blind treatment demonstrated significant improvement in all HRQOL parameters (P < 0.001); PCS, MCS, and six subscale scores of nonresponders did not change. Between-group change score differences were significant for PCS, MCS, and seven subscales (P < 0.05 to P < 0.001). During phase II, the domperidone group maintained their HRQOL; the placebo group showed a significant decline in PCS and four subscales (P < 0.05). The between-group difference in the PCS score change was statistically significant (-1.77 vs. 0.65, P=0.05). CONCLUSIONS: Results suggest that patients with symptoms of diabetic gastroparesis experience notable HRQOL impairment and that symptomatic relief with domperidone is accompanied by improvements in HRQOL that can be sustained over 4 weeks of treatment.     

Exergetic comparison of efficiency indicators for combined heat and power (CHP)

Legislative regulations in favor of combined heat and power (CHP) production have been implemented in many countries. Although these regulations put different emphasis on power production vs. process heat production, they are based on energy quantities and not on exergy. In order to analyze and compare the exergetic consequences of the various legislations, a relative avoided irreversibility (RAI) is defined. This can be regarded as the exergy loss that is avoided when reference plants with separate production are replaced by an actual CHP plant. Some series of industrial and district heating CHP plants, under varying operational conditions, are used as test cases. It is seen that some, but not all, CHP cases are exergetically beneficial to separate generation. Comparison with the RAI allows a quantitative assessment of the various performance indicators. It is seen that exergetic improvements were only captured to a limited degree by the various energy-based efficiency indicators. Some legislatively defined indicators even appear to discourage thermodynamic improvements.     

Uncertainties in heat-pump coefficient of performance (COP) and exergy efficiency based on standardized testing

The uncertainties allowed in testing following international (ISO) and European (CEN) standards for testing of residential heat pumps (HPs) were investigated and quantified. For air/air HPs, the relative uncertainties of COP and exergy efficiency allowed by the CEN standard were found to be from 7% to 9%. For the ISO standard the figures were from 5% to 10%. For air/water HPs, the CEN standard allowed up to 9% relative uncertainty in the COP and 7% in the exergy efficiency. In addition to the uncertainties described in the standards, it was also shown how to estimate the uncertainty of COP due to uncertainties in the levels of temperature where the heat transfer occurs. For air/air HPs at standard rating conditions, this contributed 3% to the relative uncertainty of the COP and the exergy efficiency. Exemplary calculations based on published test data showed that very few HPs had performance clearly above or below those with the median results. The exergy efficiency of the air/air HPs, with some exceptions, showed a decrease with increasing outdoor temperature. A similar, but weaker tendency was observed for air/water HPs. The exergy efficiencies for air/water HPs were typically found in the range from 0.3 to 0.4.     

THERMODYNAMICS OF ASPHALTENE PRECIPITATION AND DISSOLUTION INVESTIGATION OF TEMPERATURE AND SOLVENT EFFECTS

ABSTRACT

Petroleum asphaltenes have been precipitated in solvent mixtures of n-heptane and toluene at various temperatures, likewise n-heptane asphaltenes have been dissolved in under similar conditions. This give added evidence to apparent hysteresis phenomenon between the two processes. The Asphaltenes have been characterized showing that although data is scattered convergence to certain structural parameters as incipient flocculation is approached. The asphaltenes are seen to consist of an associating and a non-associating part. The solubility of asphaltenes has been correlated/modelled using the Flory-Huggins equation using two different terms for the Flory parameter. A process for evaluation of best choice of solubility parameter and molar volume for the asphaltenes is proposed. Dissolution processes are seen to be best fitted by the equations. Based on these findings the asphaltenes are proposed to be formed by a colloidal and a true solution part.     

SEPARATION OF ASPHALTENES BY POLARITY USING LIQUID-LIQUID EXTRACTION

ABSTRACT

In order to investigate the nature of petroleum asphaltenes in terms of polarity a process was developed using initial liquid-liquid extraction of the oil phase followed by precipitation of the asphaltenes using n-heptane. The liquid-liquid extraction was performed using toluene-methanol mixtures with increasing content of toluene. Although large fractions of the crude oil (Alaska '93) was extracted in the higher polarity solvents (high concentration of methanol), the asphaltene content of the dissolved material was low As the toluene content increased more asphaltenes were transferred to the solvent phase. The asphaltenes were analysed using FTir, Elemental analysis, and HPLC-SEC with a diode array detector. With increasing content of toluene in the methanol the molecular weight distribution of the asphaltenes significantly move to higher molecular weights. The content of nitrogen and sulfur of the mallene phase also increase while H/C decreases. The content of heteroatoms in the asphaltenes are relatively higher and apparently increase with the polarity of the solvent. It is concluded that these asphaltenes are indeed dominated by high molecular weight substances that cannot be extracted in the high polarity solvents