High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Mobile Device Security Using Transient Authentication

Mobile devices are vulnerable to theft and loss due to their small size and the characteristics of their common usage environment. Since they allow users to work while away from their desk, they are most useful in public locations and while traveling. Unfortunately, this is also where they are most at risk. Existing schemes for securing data either do not protect the device after it is stolen or require bothersome reauthentication. Transient Authentication lifts the burden of authentication from the user by use of a wearable token that constantly attests to the user's presence. When the user departs, the token and device lose contact and the device secures itself. We show how to leverage this authentication framework to secure all the memory and storage locations on a device into which secrets may creep. Our evaluation shows this is done without inconveniencing the user, while imposing a minimal performance overhead     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.