Permeability characteristics of carbonated concrete considering capillary pore structure

During carbonation process, the calcium phases present in cement are attacked by CO₂ and converted into CaCO₃ and the permeability of concrete is changing due to the change in porosity. The rate of carbonation depends upon porosity and moisture content of the concrete. Especially in underground reinforced concrete structures, the interior portion of concrete surface may be exposed to carbonation and the exterior portion of concrete surface exposed to wet soil or underground water. As carbonation proceeds from outer surface into internal portion of concrete, microstructure is also changed continuously from outer surface into internal portion of concrete. Even the deteriorations in the structures due to the carbonation have been reported more, research on permeability characteristics of concrete considering carbonation and micro-structural information is very scarce.In this study, the permeability coefficient in carbonated concrete is derived by applying a capillary pore structure formation model in carbonated cement mortar and assuming that aggregates do not affect carbonation process in early-aged concrete as a function of porosity. The permeability obtained from the micro-level modeling for carbonated concrete is verified with the results of accelerated carbonation test and water penetration test in cement mortar.     

Atmospheric Dependence on Dielectric Loss of 1/6Ba5Nb4O15· 5/6BaNb2O6 Ceramics

Samples of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ along with the pure end members, Ba₅Nb₄O₁₅ and BaNb₂O₆, were sintered under low oxygen partial pressure. The degradation mechanisms of dielectric loss in this reducing atmosphere have been studied. We found that the degradation occurred primarily due to the formation of oxygen vacancies caused by the reduction of Nb⁵⁺. This was determined by measuring the electrical conductivity, and through X-ray photoelectron spectroscopy. More importantly, the dielectric loss of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ samples with higher temperature stability was further decreased on sintering in a reducing atmosphere. This observation has been explained by considering the increased porosity and formation of a reduced second phase, Ba_0.65NbO₃.     

Numerical and experimental investigation of three-dimensional flow in extrusion dies

The univariant element, Q₁ P₀, and the multivariant elements, QP₀ and R P₀, are compared for the numerical simulation of the flow in extrusion dies. The pressure distribution obtained by using the Q₁ P₀ element was found to be afflicted with the checkerboard pressure mode. On the other hand, the multivariant elements, Q P₀ and R P₀, gave accurate and physically reasonable velocity and pressure distributions. The computed values of the pressure drop across extrusion dies matched well with the pressure drop determined experimentally.     

Properties of chitosan‐based biopolymer films with various degrees of deacetylation and molecular weights

An increase in the depolymerization of chitosan was found with an increased concentration of sodium perborate. Acetic anhydride was added to reacetylated chitosan in a molar ratio per gulcosamine unit, and the amide I band of IR spectra changed with the addition of acetic anhydride. Sixteen chitosans with various molecular weights (MWs) and degrees of deacetylation (DODs) were prepared. X‐ray diffraction patterns indicated their amorphous and partially crystalline states. Increases in the chitosan MW and DOD increased the tensile strength (TS). TS of the chitosan films ranged from 22 to 61 MPa. However, the elongation (E) of chitosan films did not show any difference with MW. TS of chitosan films decreased with the reacetylation process. However, E of chitosan films was not dependent on DOD. The water vapor permeabilities (WVPs) of the chitosan films without a plasticizer were between 0.155 and 0.214 ng m/m² s Pa. As the chitosan MW increased, the chitosan film WVP increased, but the values were not significantly different. Moreover, the WVP values were not different from low DOD to high DOD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3476–3484, 2003     

Thermal and mechanical properties of the polymers synthesized by the sequential polymerization of propylene and 1‐hexadecene

The block copolymer of poly(1‐hexadecene) (PHD) and polypropylene (PP) was effectively synthesized by the sequential polymerization of propylene and 1‐hexadecene by using highly isospecific TiCl₃/Cp₂Ti(CH₃)₂ (Cp = cyclopentadienyl). The block copolymers had two separate melting temperatures of constituent blocks. The modulus of PHD–PP block copolymer was enhanced as the content of sequentially polymerized PP block was increased. The elongation at break showed positive deviation at the intermediate compositions from the simple additive values of constituent homopolymers. Shape memory effect which utilizes the crystalline PHD block as a reversible phase and the crystalline PP block as a fixed structure was examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1709–1715, 2002; DOI 10.1002/app.10551     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Encapsulation mechanism of N2 molecules into the central hollow of carbon nitride multiwalled nanofibers

Nitrogen molecules have been encapsulated into the central hollows of vertically aligned carbon nitride (CN) multiwalled nanofibers by dc plasma-enhanced chemical vapor deposition with C₂H₂, NH₃, and N₂ gases on a Ni/TiN/Si(1 0 0) substrate at 650 °C. X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure spectra showed the existence of nitrogen molecules in CN nanofibers. Elemental mapping images with electron energy loss spectroscopy of the CN nanofiber and catalyst metal, and optical emission spectroscopy spectra of the plasma showed the distribution of nitrogen atoms and molecules in the CN nanofiber, catalyst metal, and gaseous precursor, respectively. These studies showed that atomic nitrogen diffused into the catalytic metal particle because of the concentration gradient and then saturated at the bottom of the particle. Saturated nitrogen atom participated in the formation of the CN nanofiber wall but most of nitrogen was trapped in the central hollow of the nanofiber as molecules.     

Application of essential work of fracture concept to toughness characterization of high‐density polyethylene

Deformation and fracture toughness of high‐density polyethylene (HDPE) in plane‐stress tension was studied using the concept of essential work of fracture (EWF). Strain range for necking was determined from uniaxial tensile test, and was used to explain the deformation transition for 2‐staged crack growth in double‐edge‐notched tensile test. Through work‐partitioning, EWF values for HDPE were determined for each stage of the crack growth. Appropriateness of these EWF values to represent the material toughness is discussed. The study concludes that the EWF values for ductile polymers like HDPE may not be constant, but vary with the deformation behaviour involved in the crack growth process. POLYM. ENG. SCI., 47:1327–1337, 2007. © 2007 Society of Plastics Engineers     

Robust person re-identification via graph convolution networks

Person re-identification (re-id) aims to identity the same person over multiple cameras; it has been successfully applied to various computer vision applications as a fundamental method. Owing to the development of deep learning, person re-id methods, which typically use triplet networks based on triplet loss, have demonstrated great success. However, the appearances of people are similar and hence difficult to distinguish in many cases. Therefore, we present a novel graph convolution network and enhances traditional triplet loss functions. Our method defines reference, positive, and negative features for triplet loss as three vertices of a graph, respectively, and adjusts their mutual distance through learning. The method adopts graph convolutions efficiently, thereby affording low computational costs. Experimental results demonstrate that our method is superior to the baseline on the Market-1501 dataset. The proposed GCN-based triplet loss considerably contributes to improve re-identification methods quantitatively and qualitatively.

     

Effects of foundation damage and water-level change on vibration modal parameters of gravity-type caisson structure

In this paper,the effects of foundation damage and water-level change on vibration characteristics of gravity-type caisson structure are examined by analyzing modal parameters extracted from output-only information.To achieve the objective,the following approaches are implemented.Firstly,vibration response analysis methods are selected to estimate power spectral density and modal parameters such as natural frequency,damping ratio and mode shape of a lab-scale caisson structural system.Secondly,vibration tests on the lab-scale caisson system are performed under a series of test scenarios which include three water-level changes and three damage levels.Thirdly,experimental modal parameters corresponding to the damaging cases as well as the water level cases are extracted by frequency domain decomposition method and stochastic subspace identification method.Finally,the effects of the water-level variation and foundation damage on the extracted modal parameters are examined to assess the feasibility of the vibration-based damage detection in gravity-type caisson structures under water-level uncertainty.