Cascaded Mirror Array: design and demonstration of low-cost light-weight digital scanning

Microsystem Technologies - A new digital scanning approach is proposed and its feasibility is demonstrated. The Cascaded Mirror Array applies an array of reflectors, with each reflector movable...     

Hypocalcemic-induced tetany that causes triceps and bilateral quadriceps tendon ruptures

Small-cell carcinoma (also known as oat-cell carcinoma) is a rare tumor that previously concerns the lung; small-cell carcinoma of the bladder is extremely rare (0.5% of all bladder malignancies). The Authors report here the case of a 78th years old man. Fourteen months before our observation he was submitted to a partial cystectomy for a small-cell carcinoma of the bladder cupola. There was no evidence of extra-vesical location at that moment and the patient was not submitted to any adjuvant therapy. At the moment of our observation the disease was very advanced and the patient died in a few time. The Authors discuss about the therapy of bladder small-cell carcinoma in the few cases described by the literature and about the survival of those patients. A radical surgical treatment in association with an adjuvant chemo- or radiotherapy appears as a better way to treat these patients. On account of this case the Authors agree with this choice and conclude that only a combined treatment can allow a better survival.     

Impact of Site-Specific Benzo[a]Pyrene Diol Epoxide-dG Lesions at or near Single/Double-Strand DNA Junctions on DNA Bending

Adducts derived from the binding of the (+)-7R,8S,9S,10R and (?)-7S,8R,9R,10S enantiomers of r7,t8-dihydrodiol-t9,10-epoxy-7,8,9,10-tetrahydrobenzo[a]pyrene (anti-BPDE) to 2′-deoxyguanosine residues in DNA are known to induce mutations due to error-prone DNA replication. Because the conformational properties of these lesions may be important in these phenomena, we have examined the effects of the stereoisomeric (+)- and (?)-trans-anti-[BP]-N ²-dG lesions positioned site-specifically at or near primer/template oligonucleotide junctions on DNA bending using high resolution gel electrophoresis. Remarkable differences in electrophoretic mobilities μ are observed in the two adducts derived from the tumorigenic (+)-anti-BPDE, and the non-tumorigenic (?)-anti-BPDE enantiomer. With the (+)-trans lesion positioned on the template strand adjacent to the 3′-end of the primer strand, a remarkable decrease in μ is observed. This suggests the existence of a bend at the single strand-double strand junction. Only modest decreases in μ are observed in the case of the (?)-trans lesion, or when the 3′-end is opposite to, or more distant from the lesion site. These observations are discussed in terms of the known NMR solution structures of these lesions in the same sequence context, and the properties of primer/template DNA in polymerases.     

Effects of molecular weight and molecular structure of low profile additives on the properties of bulk molding compound (BMC)

The effects of molecular weight and molecular structure of styrene(St)‐based and vinyl acetate(VAc)‐based low‐profile additive (LPA) on the curing kinetics and compatibility of unsaturated polyester (UP)/LPA system and linear shrinkage, water absorption rate, surface gloss and pigmentability of bulk molding compound (BMC) were investigated. Results show that the curing reaction rate decreases with an increase of the molecular weight of LPA due to the chain entanglement effect. The plasticizing effect of LPA on the (UP) network was reduced with an increase of the molecular weight of LPA. Water absorption of BMC increases as the molecular weight of LPA increases, implying that more microvoids were formed inside the BMC, resulting a lower linear shrinkage rate, and worse pigmentability. However, good shrinkage control LPA does not necessarily lead to a smoother surface and better surface gloss. Furthermore, modified LPAs possess better compatibility with UP, the final curing conversion of UP is elevated, and both better shrinkage control and surface properties are also observed.     

Dynamic variable depth of cut machining using piezoelectric actuators

This paper describes the design of a piezoelectric actuated cutting tool and implementation of digital servo controls for machining surfaces with dynamically varying depth of cut. Through a flexure hinge, the tool holder could generate 50 μm travel at the tip of the cutting insert. Tool motion errors of less than 0.5 μm were achieved in tracking cyclic waveforms by employing a digital repetitive servo control. When applied to turning aluminum and steel workpieces with variable depth of cut using carbide tools, less than 5 μm machined surface errors were measured.     

Effects of exit back-up on delamination in drilling composite materials using a saw drill and a core drill

Machining of composites has caught greater attention in manufacturing of structural parts in aerospace, automobile and sporting goods. Composite materials have advantageous features in strength and stiffness coupled with lightweight compared to the conventional metallic materials. Amongst all machining operations, drilling is the most commonly applied method for generating holes for riveting and fastening the structural assembly. Delamination is one of the serious concerns in drilling holes in composite materials at the bottom surface of the workpiece (drill exit). Quite a few references of the drilling of fiber-reinforced plastics report that the quality of cut is strongly dependent on drilling parameter as well as the drill geometry. Saw drills and core drills produce less delamination than twist drills by distributing the drilling thrust toward the hole periphery. Delamination can be effectively reduced or eliminated by slowing down the feed rate when approaching the exit and by using back-up plates to support and counteract the deflection of the composite laminate leading to exit side delaminations. The use of the back-up does reduce the delamination in practice, which its effects have not been well explained in analytical fashion. This paper predicts the effects of backup plate on delamination in drilling composite materials using saw drill and core drill. The critical drilling thrust force at the onset of delamination is calculated and compared with that without backup. The well known advantage of industrial use of backup can be understood fundamentally by the fact that the threshold thrust force at the onset of delamination is increased making the delamination less induced.     

Interfacial reactions of liquid Sn and Sn-3.5Ag solders with Ag thick films

The interfacial reactions of liquid Sn and Sn-3.5Ag solders with Ag thick films are investigated in the temperature range from 250–325 °C, and the morphology of intermetallic compounds formed after such soldering reactions is observed. In kinetics analysis of the growths of intermetallic compounds, it was found that both Sn/Ag and Sn-3.5Ag/Ag reactions were interfacial-controlled, and the growth rates for both cases were similar. The rate of Ag dissolution into liquid solder attendant on the formation of interfacial intermetallic compounds after Sn/Ag reaction was about four times higher than that after Sn-3.5Ag/Ag reaction, as evidenced by experimental results.