Prediction of Speech Quality Based on Resilient Backpropagation Artificial Neural Network

The paper presents a system for monitoring and assessment the speech quality in the IP telephony infrastructures using modular probes. The probes are placed at key nodes in the network where aggregating packet loss data. The system dynamically measures speech quality and results are collected on a central server. For data analysis we applied four-state Markov model for modeling the impact of network impairments on speech quality, afterwards, the resilient back propagation (Rprop) algorithm was used to train a neural network. Information about the speech quality are displayed in the form of automatically generated graphs and tables. The proposed solution has been tested with selected codecs and further generalizes the already presented concepts of the speech quality estimation in the IP environment.

     

Failure Resistance of the Historic Stone Bridge Structure of Charles Bridge. I: Susceptibility to Nonstress Effects

The monitoring of deformations of the stone structure of Charles Bridge in Prague proved the gravity and relevance of nonstress effects (temperature, moisture content) on cyclic deformations and permanent strain accompanied by a gradual disintegration of its stone masonry, growing tilt of the breast walls, and development of cracks in the masonry of the stone bridge structure. Each deformation cycle is accompanied by a gradual growth in permanent deformations. The “unmanifested” primary deformation due to, e.g., a temperature change causes a mechanical state of tension, and it is mainly the tensile stresses thus arising that contribute to the development of tensile cracks in the stone masonry.     

Problem of the reference height of the projectile trajectory as a reduced meteo-ballistic weighting factor

This paper deals with the issue of preparation of the aiming angles with the use of tabular firing tables and needed determination of the ballistic elements μB （ballistic wind wB Wxm WzB, ballistic （virtual） temperature τB, ballistic density ρB） from the standardized met messages. The weighting factors are used for the calculation of ballistic elementsμB that are incorporated into the trajectory calculations characteristics of weapon and ammunition. Two different methodologies practically used in the praxis are analysed and compared. For the comparison of the two methodologies the reference height of trajectory determined from the weighting factor functions is employed. On the basis of the analyses conducted, the potential for further increase in accuracy of these aiming angles preparation methods is pointed out.     

Untersuchung der thermisch‐hygrischen Eigenschaften von Ziegeln mit Hohlraumfüllung aus Recyclingmaterial

Investigation on the thermal‐hygral behaniour of bricks with canity filling by recycling meterials. In the investigation project was examined whether bricks with simple cavity structure have a higher heat resistance by use of a heat insulation material filling in the cavities. The insulation material is a recycled product made of polystyrene and wood covered and bonded with cement. The influence of the configuration and thickness of the perforated bricks with vertical perforations and the geometry of the cavities of the brick on the thermal moisture states was evaluated. For investigation of the thermal resistance and the heat transmission coefficients were used the simulation program THERM, that considered the heat transportation through conduction in the brick fragments and the transport mechanisms conduction, convection and radiation in the airfilled cavities. The software package WUFI 2D was employed for the investigation of moisture transfer in the bricks. The investigations showed that the composite brick insulation stone has a thermal resistance twice as high as the initial brick. The moisture states can be partially in the brick more than 80 % humidity. This load is estimated as uncritical because the wooden particles are covered with cement slime.     

A model for cell-surface-exposed carbohydrate moieties suitable for structural studies by NMR spectroscopy

In the present study a synthetic glycolipid system is presented that can be readily incorporated into phospholipid micelles and that allows the study of cell-surface-exposed carbohydrate units by high-resolution NMR techniques. Here, we present an efficient route for the synthesis of glycolipid compounds that contain mannose, mannobiose, or mannotriose coupled either directly to an alkyl chain or through a poly(ethylene glycol) linker. Furthermore, we have validated our model system by measuring the binding of cyanovirin N (CV-N), a cyanobacterial protein that binds with nanomolar affinity to the terminal arms of high-mannose structures of the HIV surface-envelope glycoprotein gp120, to glycolipids the carbohydrate portions of which comprise the corresponding high-mannose moieties. From the results of chemical-shift mapping with uniformly (15)N-labelled CV-N, we conclude that binding to the protein occurs at sites similar to those involved in binding the nonconjugated carbohydrates. We characterized the insertion of the glycolipids into dodecylphosphocholine (DPC) micelles by measuring translational diffusion, and we observed that the diffusion constants of the glycolipids were very similar to those of the DPC micelles themselves, but significantly deviated from those of the free glycolipids. We also present experimental proof that the glycolipids remain inserted in the micelles while binding to CV-N. Finally, by addition of a ligand that had a higher affinity to CV-N but which was not attached did not couple to a lipid anchor, CV-N could be released from the glycolipid and, hence, from the micelle-associated state.     

Firefly luciferase produces hydrogen peroxide as a coproduct in dehydroluciferyl adenylate formation

Firefly luciferase catalyzes the synthesis of H2O2 from the same substrates as the bioluminescence reaction: ATP and luciferin (D-LH2). About 80% of the enzyme-bound intermediate D-luciferyl adenylate (D-LH2-AMP) is oxidized into oxyluciferin, and a photon is emitted during this reaction. The enzyme pathway responsible for the generation of H2O2 is a side reaction in which D-LH2-AMP is oxidized into dehydroluciferyl adenylate (L-AMP). Like the bioluminescence reaction, the luciferase-catalyzed synthesis of H2O2 and L-AMP is a stereospecific process, involving only the natural D enantiomer. However, the intramolecular electron transfer postulated as essential to the light emission process is not involved in this side reaction.     

Extrusion of polyethylene/polypropylene blends with microfibrillar‐phase morphology

Extrusion of immiscible polymers under special conditions can lead to creation of microfibrillar‐phase morphology, ensuring significant increase of mechanical properties of polymer profiles. Polyethylene/polypropylene blend extrudates with microfibrillar‐phase morphology (polypropylene microfibrils reinforcing polyethylene matrix phase) were prepared through continuous extrusion with semihyperbolic‐converging die enabling elongation and orientation of microfibrils in flow direction. Structure of extruded profiles was examined using electron microscopy and wide‐angle X‐ray scattering. Tensile tests proved that extrudates with microfibrillar‐phase morphology show significantly higher mechanical properties than the conventional extrudates. The presented concept offers possibility of replacing the existing expensive multi‐component medical devices with fully polymeric tools. POLYM. COMPOS., 31:1427–1433, 2010. © 2009 Society of Plastics Engineers     

Non-destructive Real Time Monitoring of the Laser Welding Process

Laser welding is a high power density technology of materials joining that has many advantages in comparison with conventional fusion welding methods, for example, high accuracy, flexibility, repeatability and especially very narrow heat-affected zone which results in minimal workpiece distortions. Since it is still quite expensive technology, minimal spoilage is required. Effective system of quality control and processing parameters optimization must be established to reduce total costs, which is particularly required in industrial production. In this article some results of pulsed Nd:YAG laser welding process monitoring based on the measurement of plasma electron temperature are presented. The ability of designed sensor to detect weld penetration depth has been demonstrated. Plasma spectral lines intensities measurement can discover gap instabilities as well as local sheet thickness reduction.     

Surface functionalization of mesoporous antimony doped tin oxide by metalorganic reaction

Electrically conducting mesoporous antimony doped tin oxide was functionalized by the metalorganic reaction with several Grignard reagents. This fast and efficient grafting approach enables a direct connection of the metal atoms with the organic functionalities avoiding the formation of insulating Si–O linkers, which is of special interest for the interfacial charge transfer processes. Using this approach we introduced vinyl, allyl and phenyl groups into the pores of mesoporous ATO, which was confirmed by IR spectroscopy, TGA and nitrogen sorption measurements. We obtained a high loading of organic groups corresponding to about 50–60% of the monolayer surface coverage. The obtained mesoporous inorganic–organic hybrids can serve as a platform for incorporation of electrochemically active species.     

Flow patterns and velocity fields in two-dimensional thin slice panel with flow-corrective insert

An experimental two-dimensional (2-D) thin slice panel for studying flow patterns of fine silica sand was designed and manufactured. As supplier of sand was not known at that time, flow properties of the silica sand were assessed without shear tests. A preliminary design of plane-flow hopper of the experimental 2-D panel was assumed to be close to the mass flow conditions. Sand was circulated in the experimental panel to study the steady state flow. Tests of flow patterns suggested typical funnel-flow patterns with stagnant zones in the hopper and in the vertical part of the panel. Stagnant zones near the bottom of the hopper indicated insufficient width of the hopper outlet. Shear tests for estimation of flow properties of silica sand were carried out additionally and two methods of how to transform the funnel flow of sand to the mass flow were followed up; (a) existing 2-D panel was retrofitted with flow-corrective element, and (b) the width of outlet in existing experimental panel was widen into the size, calculated according to mass flow conditions. Both modifications were proven to be successful and the last-in first-out funnel flow was transformed into first-in first-out mass flow of sand. Velocities of individual tracer particles were measured during mass flow and velocity field was evaluated. Velocity profile of particles in the vicinity of flow-corrective insert was studied in detail.