Forecasting electric power generation in a photovoltaic power system for an energy network

Recently, there has been an increase in concern about the global environment. Interest is growing in developing an energy network by which new energy systems such as photovoltaic and fuel cells generate power locally and electrical power and heat are controlled with a communication network. We developed the power generation forecast method for photovoltaic power systems in an energy network. The method makes use of weather information and regression analysis. We carried out forecasting power output of the photovoltaic power system installed in Expo 2005, Aichi Japan. As a result of comparing measurements with prediction values, the average prediction error per day was about 26% of the measured power. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 167(4): 16–23, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20755     

Current reliability issues and future technologies for systems on silicon – processes, circuits, chip architecture, and design

The progress of silicon technology is opening the era of “systems on silicon” in which a large-scale memory, a CPU, and other logic macros will be integrated on a single chip. These kinds of chips, called system LSIs, have an especially promising future in mobile and multimedia applications but face inherent technical problems related to the reliability of ultrathin oxide film, conflict in the processing of different components, increased gate and subthreshold leakage currents, memory bottlenecks, and design complexity. This paper reviews the system LSIs and then introduces related technologies in processing, circuits, chip architecture, and design. It also discusses the influence of the system LSIs on business strategies.     

Large-Scale Shake Table Experiment and Numerical Simulation on the Nonlinear Behavior of Pile-Groups Subjected to Large-Scale Earthquakes

This paper describes the results of large-scale shake-table experiments involving a 3×3 pile-group. The pile-group was embedded in dry sand and subjected to sinusoidal waves and an earthquake motion recorded from the 1995 Hyogo-ken Nanbu (Kobe) earthquake. The load transfer between soil and pile was derived and the group effect was captured. Numerical simulations were also performed using a Beam-on-Nonlinear-Winkler-Foundation approach with a new hysteretic p-y curve. A comparison of the experimental and numerical results revealed that the numerical simulation is capable of accounting for the soil-pile interaction observed in the experiment.     

Secondary neutral and ionized particle measurements under MeV-energy ion bombardment

We have measured both secondary neutral and ionized particles from an InSb target under 3.0 MeV Si ion bombardment. Measurements of both ions and neutrals have not been carried out so far in the MeV-energy range. The mass spectra and axial emission energy distributions of secondary particles were investigated. Secondary ions were measured with a linear- and a reflective-type time-of-flight technique, whereas secondary neutral particles were photo-ionized by a UV pulsed laser (ArF: 193 nm) and measured with a reflective-type time-of-flight technique. Different results were obtained for neutral particles in comparison with ionized particles. The mean energy of neutral Sb atoms was much lower than that of neutral In atoms, whereas the mean energies of secondary In and Sb ions were nearly equal.     

升温下钢构件的强度设计标准

通过与非线性有限元模拟比较,对结构钢构件在升温下的设计公式进行了评估。比较美国钢协与欧洲标准委员会对温度在800℃侧向无支撑的Ⅰ型柱、梁、柱-梁的设计规定。欧洲规范3的规定与有限元模拟的结果相差10%～20%。另一方面,美国钢协的规范预测的强度与模拟结果相差高达2倍。对于温度超过300℃的中细构件,相差最大。提出了对美国钢协规范计算公式的修正建议,修正后的精度与模拟的结果误差在20%～30%。最后讨论了结构防火工程基于构件评估的局限性、未来的研究以及发展方向。     

Radiation grafting of α,β,β-trifluorostyrene onto poly(ethylene-tetrafluoroethylene) film by preirradiation method. II. Properties of cation-exchange membrane obtained by sulfonation and hydrolysis of the grafted film

A Study was made on certain properties of the cation-exchange membranes obtained by the preirradiation grafting of α,β,β-trifluorostyrene (TFS) noto poly(ethylene-tetrafluoroethylene) (ETFE), followed by sulfonation and hydrolysis of the grafted film. Swelling, water uptake, electric conductivity, and transport number of the membranes were measured as a function of ino-exchange capacity. Thermal and chemical stability were also investigated. These properties were found to be mainly dependent on ion-exchange capacity. The stable membrane properties were established due to a homogeneous ion-exchange group distribution in the membrane, as confirmed by x-ray imcroscopy analysis of the membrane cross sections. In addition, the membranes showed good electrochemical, thermal, and chemical properties, and were found to be scceptable for practical use as cation-exchange membranes.     

Repeatedly foldable AMOLED display

In this study, a 5.9‐inch foldable active‐matrix organic light emitting diode (AMOLED) display was developed. A folding test was performed repeatedly. The display survived the folding test (100,000 folds) with a curvature radius of 2 mm. To protect an organic light emitting diode (OLED) against moisture, inorganic passivation layers are provided on the upper and lower sides of the flexible display. Using our transfer technology, high density passivation layers can be obtained. The measured water vapor transmission rate of the layer is 7 × 10^?6 g/m²?day or less, which improves OLED reliability. With these techniques, we have developed a book‐type display, which is repeatedly foldable like a book, and a tri‐fold display including a display area, which is foldable in three.     

The effect of permanent dipole moments of adsorbates upon I-V characteristics of a bilayer tunneling junction between self-assembled monolayers on an Au(111) substrate and a gold tip

It is important to understand an electronic property of an interface between an organic material and a metal electrode. In the present work, we measured current-voltage (I-V) curves of self-assembled monolayers (SAMs) on Au(111) using a conducting atomic force microscope (AFM) with chemically modified Au-coated AFM tips. This contact resulted in a bilayer junction between the Au(111) substrate covered with one SAM and the Au-coated tip with the other SAM. An alkanethiol (octanethiol) and benzenemethanethiols with various terminal groups (-H, -CH(3), -Cl, -CF(3)) were used as the adsorbates. The shapes of the I-V curves depended on the terminal groups. This phenomenon was attributed to the change in the work function of gold due to different permanent dipole moments of the terminal groups.