New interrupted cooling experiments have been designed to study the kinetics of bainitic ferrite formation starting from a mixture of austenite and bainitic ferrite. It is found that the kinetics of bainitic ferrite formation during the cooling stage is determined by the isothermal holding time. The formation rate of bainitic ferrite at the beginning of the cooling decreases with increasing prior isothermal holding time. An unexpected stagnant stage during the cooling stage appears when the isothermal holding time increases to a critical point. There are two reasons for the occurrence of the stagnant stage: (i) a solute spike in front of the interface; and (ii) kinetic transition. A so-called Gibbs energy balance approach, in which the dissipation of Gibbs energy due to diffusion inside the interface and interface friction is assumed to be equal to the available chemical driving force, is applied to theoretically explain the stagnant stage. A kinetics transition from a fast growth mode without diffusion of Mn and Si inside the austenite–bainitic ferrite interfaces to a slow growth mode with diffusion inside the interface is predicted. The stagnant stage is caused by the transition to a slow growth mode. The Gibbs energy balance approach describes the experimental observations very well. 相似文献
In the present work, the size distribution and shape of WC grains in cemented carbides (WC–Co), with different Co contents, have been investigated in three dimensions. Direct three-dimensional (3-D) measurements, using focused ion beam serial sectioning and electron backscattered diffraction (EBSD), were performed and a 3-D microstructure was reconstructed. These measurements were supplemented by two-dimensional (2-D) EBSD and scanning electron microscopy on extracted WC grains. The data from 2-D EBSD collected on planar sections were transformed to three dimensions using a recently developed statistical method based on an iterative inverse Saltykov procedure. This stereological analysis revealed that the assumed spherical shape of WC grains during the Saltykov method is reasonable and the estimated 3-D size distribution is qualitatively in good agreement with the actual distribution measured from 3-D EBSD. Although the spherical assumption is generally fair, the WC grains have both faceted and rounded surfaces. This is a consequence of the relatively low amount of liquid phase during sintering, which makes impingements significant. Furthermore, the observed terraced surface structure of some WC grains suggests that 2-D nucleation is the chief coarsening mechanism to consider. 相似文献
Intradialytic hypotension (IDH) is one of the most important short-term complications to hemodialysis (HD). Inadequate cardiac filling due to a reduction in the central blood volume is believed to be a major etiological factor. The aim of this study was to evaluate whether these pathophysiologic events are reflected in the central venous oxygen saturation (ScO(2)) and thoracic admittance (TA) during dialysis. Twenty ambulatory HD patients, 11 hypotension prone (HP) and 9 hypotension resistant, with central vascular access, were monitored during 3 HD sessions each. ScO(2), TA, finger blood pressure (BP), and relative change in blood volume (DeltaBV) were measured and sampled continuously. The relative TA decrease and DeltaBV were both largest in the HP group (p<0.05 for both), whereas ScO(2) decreased only in HP patients (p<0.001). Baseline TA was lower in the HP group (p<0.01). Changes in ScO(2) and TA correlated much closer than did changes in ScO(2) and DeltaBV (r=0.43 and 0.18, respectively). Our results suggest that an intradialytic decrease in cardiac output, as reflected by a fall in ScO(2), is a common feature to HD patients prone to IDH. In patients using a central vascular access, ScO(2) and TA measurements may be more specific to the pathophysiologic events preceding IDH than DeltaBV-the current standard monitoring method. 相似文献
The effects of atmospheric processing on soot particle morphology were studied in the laboratory using the Differential Mobility Analyzer-Aerosol Particle Mass Analyzer (DMA-APM) and the DMA-DMA (Tandem DMA) techniques. To simulate atmospheric processing, combustion soot agglomerates were altered by sulphuric acid vapor condensation, relative humidity (RH) cycling, and evaporation of the sulphuric acid and water by heating. Primary investigated properties were particle mobility size and mass. Secondary properties, derived from these, include effective density, fractal dimension, dynamic shape factor, and the mass fraction of condensed material. A transformation of the soot particles to more compact forms occurs as sulphuric acid and water condense onto fresh soot. The particle mass increases and initially the mobility diameter decreases, indicating restructuring of the soot core, likely due to surface tension forces. For a given soot source and condensing liquid, the degree of compaction depends strongly on the mass (or volume) fraction of condensed material. For water and sulphuric acid condensing on combustion soot, a mass increase of 2–3 times is needed for a transformation to spherical particles. In the limit of spherical particles without voids, the effective density then approaches the inherent material density, the fractal dimension approaches 3 and the dynamic shape factor approaches 1. Our results indicate that under typical atmospheric conditions, soot particles will be fully transformed to spherical droplets on a time scale of several hours. It is expected that the morphology changes and addition of soluble material to soot strongly affect the optical and hygroscopic properties of soot. 相似文献
Phase-field modeling is used to simulate the formation of sigma phase in a model alloy mimicking a commercial super duplex stainless steel (SDSS) alloy, in order to study precipitation and growth of sigma phase under linear continuous cooling. The so-called Warren–Boettinger–McFadden (WBM) model is used to build the basis of the multiphase and multicomponent phase-field model. The thermodynamic inconsistency at the multiple junctions associated with the multiphase formulation of the WBM model is resolved by means of a numerical Cut-off algorithm. To make realistic simulations, all the kinetic and the thermodynamic quantities are derived from the CALPHAD databases at each numerical time step, using Thermo-Calc and TQ-Interface. The credibility of the phase-field model is verified by comparing the results from the phase-field simulations with the corresponding DICTRA simulations and also with the empirical data. 2D phase-field simulations are performed for three different cooling rates in two different initial microstructures. A simple model for the nucleation of sigma phase is also implemented in the first case. Simulation results show that the precipitation of sigma phase is characterized by the accumulation of Cr and Mo at the austenite-ferrite and the ferrite-ferrite boundaries. Moreover, it is observed that a slow cooling rate promotes the growth of sigma phase, while a higher cooling rate restricts it, eventually preserving the duplex structure in the SDSS alloy. Results from the phase-field simulations are also compared quantitatively with the experiments, performed on a commercial 2507 SDSS alloy. It is found that overall, the predicted morphological features of the transformation and the composition profiles show good conformity with the empirical data.
Citalopram is one of several selective serotonin reuptake inhibitors (SSRIs) commonly found in treated sewage effluents. Accordingly, there are concerns about possible adverse effects of SSRIs on aquatic organisms, particularly behavioural effects similar to those associated with SSRI use in humans. Rainbow trout fry and adult male guppies were therefore exposed to waterborne citalopram, ranging from environmentally relevant to high concentrations (1, 10, 100 μg/L) for 3-7 days. Under these experimental conditions citalopram does not appear to cause significant effects on aggression in rainbow trout fry or on sexual behaviour in male guppies. This may be explained by a relatively low uptake of citalopram from water to fish. 相似文献
In Europe work is in progress to establish new standards for materials and it is very important that accurate data are used as a basis for property values in these standards. In addition reliable evaluation methods must be employed when the values are derived. A systematic evaluation method for yield strengths at elevated temperatures has been developed which is a modification of the ISO 2605/111 (ENV22605-3) procedure. The method has been applied to a number of steel types and has proven to provide values in good accordance with experimental data. Comparisons with existing national and international standards showed the importance of using experimental values when establishing new standards. The method is intended for use in the standard developments by the European Committee for Iron and Steel Standardisation (ECISS). 相似文献