Effect of Composition on the Electromechanical Properties of (1-x)Pb(Mg1/3Nb2/3)O3−XPbTiO3 Ceramics

Ceramic lead magnesium niobate–lead titanate ((1-x)PMN_-xPT) of different compositions has been prepared by the columbite precursor method. This study discusses compositions ranging from 0.94PMN–0.06PT to 0.60PM–N0.40PT, focusing on two areas of the (1-x)PMN_xPT system: compositions that exhibit electrostrictive behavior, and those that show piezoelectric behavior. In electrostrictive compositions where x is in the range of 0.06–0.20, the dielectric constant and electromechanical coupling factor dependencies on the bias field are evaluated. The optimal electromechanical properties are obtained with the composition 0.82PMN–0.18PT, measured at temperature T = T_m (the temperature of maximum dielectric constant) = 80°C and with a dc bias of 5 kV/cm. X–ray diffractometry is used to show that the (1-x)PMN_-xPT system has a compositionally wide two–phase region and that 0.655PMN–0.345PT is the morphotropic phase boundary (MPB) composition. Electromechanical property evaluation shows that the optimal piezoelectric properties (piezoelectric charge coefficient ( d₃₃ ) value of 720 pC/N, dielectric constant ( K ) value of 5400, and electromechanical planar and thickness coupling coefficient ( k_p and k_t , respectively) values of 62% and 46%, respectively) are obtained at the MPB composition.     

Morphology and characterization of conductive films based on polyaniline‐coated polystyrene latexes

The polyaniline (PANI)‐coated polystyrene (PS) latexes were synthesized, and the electrically conductive films were prepared thereafter. The weight ratio of PANI was 5%. Thermal analysis of the latices was performed using DSC and TGA. In this study, the electrically conductive films were prepared above the PS glass transition temperature (T_g). During the film formation, the effects of the annealing temperature and atmosphere (air or N₂) on the film resistance were investigated. In addition, the film morphology was observed utilizing scanning electron microscopy. The film resistance decreased in the initial heating stage due to the increasing temperature and the compaction of film. Then the film resistance increased with further annealing due to the aging of PANI. Typically, the film resistance was about 6000 Ω/sq, and the conductivity was 0.3 S/cm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5406–5413, 2006     

Liquid-phase adsorption of dyes and phenols using pinewood-based activated carbons

Physical properties of activated carbons prepared from pinewood at different activation times (0.5, 1.5, 2.7, and 4.0 h) in steam at 900 °C were studied. The adsorption equilibria and kinetics of three dyes and three phenols (phenol, 3-chlorophenol, and o-cresol) from aqueous solutions on such carbons were then examined at 30 °C. The adsorption isotherms of phenols could be well fitted by the Freundlich equation, and those of dyes were adequately described by the Langmuir-Freundlich equation. The effect of microporosity of the carbons on adsorption capacity was explored. Four simplified kinetic models including pseudo-first-order equation, pseudo-second-order equation, intraparticle diffusion model, and the Elovich equation were selected to follow the adsorption processes. The adsorption of all six adsorbates could be best described by the Elovich equation. The kinetic parameters of this best-fit model were calculated and discussed.     

Identification of the combustion behaviour of lignite char between 350 and 900 °C

The combustion behaviour of four different lignite samples pyrolysed at 800 and 1000 °C has been studied. The reaction order and the activation energy of the char combustion reaction can be easily determined from the time to reach 50% conversion. Under 550 °C the reaction order of lignite samples are 0.7 and the activation energies are 27.4–27.9 kcal gmole^?1. Above 550 °C the measurement of the intrinsic reaction rate is limited by the film diffusion resistance. The pyrolysis temperature affects the reactivity significantly. The reactivity of char pyrolysed at 800 °C is 3.5 times that of char pyrolysed at 1000 °C.     

Influence of polymer molecular weight on selected thermodynamic properties of polymer/solvent systems and the application of the UNIFAC theory

The intrinsic viscosities of eleven narrow molecular weight distribution polystyrene samples ranging from number-average molecular weight 1820 to 1 292 000 have been determined in pure solvents of tetrahydrofuran and chloroform with a Ubbelohde No. 1 viscometer at 25°C. By combining the original and modified Fox-Flory viscosity treatments, respectively, with the Flory-Huggins Lattice theory, the interaction parameters were calculated. With the aid of original and modified UNIFAC methods the solvent activity, clustering function of the solvent, and the interaction parameter were computed and compared with the experimental data. It was established that the influence imposed by the polymer molecular weight on the activity of the solvent, the clustering function of solvent, and interaction parameter is insignificant. The modified UNIFAC method satisfactorily predicted the solvent activity as illustrated by previous investigators. However, both UNIFAC methods failed to predict the interaction parameter.     

Nanosized silica‐supported metallocene/MAO catalyst for propylene polymerization

A nanosized silica particle was used as the support to prepare an Et[Ind]₂ZrCl₂/MAO catalyst for propylene polymerization of polypropylene. The catalyst and the polymer produced were characterized with nitrogen adsorption, ICP, DSC, SEM, TEM, XRD, solution viscometer, ¹³C NMR and optical microscopy. The effects of polymerization temperature and [Al]/[Zr] ratio on catalyst activity and polymer melting point were investigated. Under identical reaction conditions, nanosized catalyst exhibited better polymerization activity than the microsized catalyst (e.g., the former had 64% higher activity than the latter at the optimum polymerization temperature (50°C) and [Al]/[Zr] = 570). DSC results indicated that polymer melting point increased with the increase of [Al]/[Zr] ratio and with the decrease of polymerization temperature. XRD results showed that the percentage of γ crystals increased with decreasing [Al]/[Zr] ratio. Electron microscopic results showed that the polymer particle size increased with increasing polymerization temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2573–2580, 2006     

Study of SO2 adsorption and thermal regeneration over activated carbon-supported copper oxide catalysts

The mechanisms of SO₂ adsorption and regeneration over activated carbon-supported copper oxide sorbent/catalysts were analyzed. Studies were carried out in a fixed-bed reactor equipped with a non-dispersive infrared gas analyzer to detect the reaction products and by using X-ray powder diffraction (XRPD) and temperature-programmed desorption (TPD) experiments to characterize the nature of the sulfate species and surface oxygen complexes. The results indicate that SO₂ was catalytically oxidized to SO₃ over a copper phase in the presence of gaseous oxygen, and then reacted with a copper site to form a sulfate linked to copper without desorption into the gas phase. The activated carbon support did not participate in this sulfation reaction. After the adsorption of SO₂, the exhausted sorbent/catalysts could be regenerated by direct heat treatment in inert gas at temperatures between 260 and 480 °C, while the neighboring surface oxygen complexes on the carbon surface were acting as the reducing agents to reduce CuSO₄ to Cu. During the subsequent adsorption process, the copper is rapidly oxidized by oxygen in the flue gas.     

Specificity of Systemically Released Cotton Volatiles as Attractants for Specialist and Generalist Parasitic Wasps

Cotton plants under herbivore attack release volatile semiochemicals that attract natural enemies of the herbivores to the damaged plant. The volatiles released in response to herbivory are not only released from the damaged leaves but from the entire cotton plant. We found that cotton plants that released myrcene, (Z)-3-hexenyl acetate, (E)--ocimene, linalool, (E)-4,8-dimethyl-1,3,7-nonatriene, (E)--farnesene, and (E, E)-4,8,12-trimethyl-1,3,7,11-tridecatetraene systemically from undamaged leaves of caterpillar damaged plants were attractive to the generalist parasitoid Cotesia marginiventris and the specialist parasitoid Microplitis croceipes. Plants from which the caterpillar damaged leaves were removed and that released those compounds systemically were significantly preferred over undamaged control plants in two-choice experiments in a flight tunnel. Artificially damaged cotton plants that released green leafy volatiles and constitutive terpenoids were less attractive for M. croceipes and C. marginiventris. Only C. marginiventris preferred artificially damaged plants over undamaged control plants, whereas M. croceipes showed no preference. The apparent lack of specificity of systemically released compounds in response to different herbivores feeding on the lower leaves is discussed.     

Synthesis and dielectric properties of polystyrene‐clay nanocomposite materials

Polystyrene‐clay nanocomposite (PsCN) materials were synthesized and their properties of crystallinity, thermal behavior, and dielectric characteristics were investigated. A polymerizable cationic surfactant, [2‐(dimethylamino)ethyl]triphenylphonium bromide, was used for the intercalation of montmorillonite (MMT). The organophilic MMT was prepared by Na⁺‐exchanged MMT and ammonium cations of a cationic surfactant in an aqueous medium. Organophilic styrene monomers were intercalated into the interlayer regions of organophilic clay hosts followed by a free‐radical polymerization. Exfoliation to 2 wt % MMT in the polystyrene (PS) matrix was achieved as revealed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Thermal properties by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were also studied. The dielectric properties of PsCNs in the form of film with clay loading from 1.0 to 5.0 wt % were measured under frequencies of 100 Hz–1 MHz at 25–70°C. A decreased dielectric constant and low dielectric loss were observed for PsCN materials. The dielectric response at low frequency that originated from dipole orientation was suppressed due to the intercalation of clay materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1368–1373, 2004     

Performance of estimating depth in projection based stereoscopic virtual display

Accurate distance estimation is essential for effective user interaction with objects appearing in the virtual space. Research has shown that the distance estimation in the virtual space is not as accurate as that in the real world. The inaccuracy phenomenon is almost exclusively documented for estimating objects appearing straight ahead of the eye. A collection of the accuracy data for targets located in different angles of view in the visual field may be useful in aiding the design of user‐virtual object interaction. This study collected the object to object distance estimation accuracy for targets displayed stereoscopically. There are five horizontal and two vertical viewing angles and three depths, resulting in a total of 30 locations in the virtual space. The distance estimation for any of the 30 object pairs were performed with or without the aid of spatial cues. Significant factors influencing the accuracy and time of distance estimation were identified. Implications of the finding were discussed with respect to the stereoscopic display environment.