Comparison of flexibility options to improve the value of variable power generation

As the share of variable generation in power systems increases, there is increasing value in more flexible use and generation of electricity. The paper compares the economic value of several flexibility options in a large power system with a large amount of reservoir hydro power. Generation planning models are needed to consider the impact of flexibility options on other investments in a power system. However, generation planning models do not include all the relevant operational details. The approach in the paper combines a generation planning model with a unit commitment and dispatch model. The results demonstrate the value of coupling the heat and power sectors and the value of transmission. Low-cost electricity storage does not appear to be as decisive in the Northern European context with wind power as the main variable generation source. The paper also addresses methodological issues related to the inclusion of operational constraints in generation planning.     

The effect of materials and obliquity of the impact on the critical velocity of rebound

The critical velocity of rebound was determined for spherical ammonium fluorescein particles in the size range of 0.44–7.3 μm. The method was based on measurements with a variable nozzle area impactor (VNAI) and numerical simulations. A comparison to previous results with spherical silver particles obtained with the same method showed that the critical velocity was approximately two orders of magnitude higher for ammonium fluorescein than for silver at the same size range. Among the hard test materials, including steel, aluminium, molybdenum, and Tedlar, the surface material had no significant effect on the critical velocity of rebound within the accuracy of the method. On the contrary, the critical velocity was observed to be highly dependent on the obliquity of the impact at the onset of rebound. While the ratio of the maximum tangential and normal velocities was defined as a measure for the obliquity, the critical velocity was found to be more than a magnitude smaller for very oblique impacts with the velocity ratio above 9 than for close-to-normal impacts with the velocity ratio below 1.5. The results of this study can be considered as a link between the recently published critical velocity results for nanoparticles and the older results for micron-sized particles.

Copyright © 2017 American Association for Aerosol Research     

Ultrasonic assessment of cortical bone thickness in vitro and in vivo

In osteoporosis, total bone mass decreases and the thickness of the cortical layer diminishes in the shafts of the long bones. In this study, a simple ultrasonic in vivo method for determining the thickness of the cortical bone layer was applied, and the suitability of two different signal analysis techniques, i.e., envelope and cepstral methods, for measuring cortical thickness was compared. The values of cortical thickness, as determined with both techniques, showed high linear correlations (r ges 0.95) with the thickness values obtained from in vitro measurements with a caliper or in vivo measurements by peripheral quantitative CT (pQCT). No systematic errors that could be related to the cortical thickness were found. The in vivo accuracy of the measurements was 6.6% and 7.0% for the envelope and cepstral methods, respectively. Further, the in vivo precision for the envelope and cepstral methods was 0.26 mm and 0.28 mm, respectively. Although the results are similar for both of the techniques, the simplicity of the envelope method makes it more attractive for clinical applications. In conclusion, a simple ultrasound measurement provides an accurate estimate of the cortical bone thickness. The techniques investigated may have clinical potential for osteoporosis screening and therefore warrant more extensive clinical investigations with healthy and osteoporotic individuals.     

Materials design principles of ancient fish armour

Knowledge of the structure-property-function relationships of dermal scales of armoured fish could enable pathways to improved bioinspired human body armour, and may provide clues to the evolutionary origins of mineralized tissues. Here, we present a multiscale experimental and computational approach that reveals the materials design principles present within individual ganoid scales from the 'living fossil' Polypterus senegalus. This fish belongs to the ancient family Polypteridae, which first appeared 96 million years ago during the Cretaceous period and still retains many of their characteristics. The mechanistic origins of penetration resistance (approximating a biting attack) were investigated and found to include the juxtaposition of multiple distinct reinforcing composite layers that each undergo their own unique deformation mechanisms, a unique spatial functional form of mechanical properties with regions of differing levels of gradation within and between material layers, and layers with an undetectable gradation, load-dependent effective material properties, circumferential surface cracking, orthogonal microcracking in laminated sublayers and geometrically corrugated junctions between layers.     

Bio-derived fuels may ease the regeneration of diesel particulate traps

Particulate is the most problematic emission from diesel engines. To comply with environmental regulations, these engines are often equipped with particulate traps, which must be regenerated frequently for the sake of efficiency. The regeneration is commonly achieved by rising the temperature in the trap till the particulate self-ignites. However, this method implies energy losses and thermal shocks in the trap. Alternatively, catalysts and additives have been recently considered for reducing the ignition temperature of particulate, but these techniques suffer from poisoning and undesirable byproducts. The present experimental study shows that the ignition temperature of particulate from seed-derived oils (SO) and from blends of SO with diesel fuel oil (DO) can be lower than that of particulate from neat DO. If substantiated by more extensive studies, such finding could have noteworthy implications on the future of fuels and traps.     

Solubility of gases in a hydroformylation solvent

The solubility of reactants used in homogeneously catalyzed hydroformylation of alkene was studied in a pressurized, semi-batch autoclave. The solubilities of alkene, carbon monoxide and hydrogen in the 2,2,4-trimethyl-1,3-pentanediol mono(2-methylpropanoate) solvent (NX 795) were determined by precise pressure and weight measurements. The measured solubilities were tested against empirical and theoretical models. Logarithmic empirical models gave a very good fit to experimental solubility data. To obtain nonempirical equations for the gas solubility, thermodynamic models based on activity coefficients and equations of state were used. The activity coefficient models based on regular solution theory (RST) predicted the solubilities well, but the selection of the model is the critical issue. For 1-butene, the best prediction was provided by the Yen and McKetta modification of the RST, whereas for carbon monoxide and hydrogen it was necessary to include a mixing entropy term in the RST. The Soave-Redlich-Kwong equation of state gave a fairly good prediction of the solubilities, but not as good as the RST-based models.     

A study on the restoration method of friction, wear and fatigue performance of remanufactured crankshaft

Crankshaft translates reciprocating linear piston motion into rotation in internal combustion engine. So it receives complex combination of stresses. Therefore, crankshaft remanufacturing process is designed thoroughly with special attention to fatigue and tribological performance. Experimental study is carried out in order to show that UNSM (ultrasonic nanocrystal surface modification) technology which will be used as final surface treatment after 0.2 mm depth surface grinding, could restore original fatigue strength and tribological performance. Furthermore the feasibility steady to replace conventional overlay welding in crankshaft remanufacturing process by UNSM (ultrasonic nanocrystal surface modification) technology is carried out. Effects of UNSM technology are established through rotary bending test, rolling contact fatigue (RCF) test and wear simulation test. The test specimen used SCM435 material of crankshaft and commercial bush. The test result showed fatigue limit improved by 30% and RCF life increased by 40% for UNSM treated specimen. And friction coefficient decreased by 24% and wear amount decreased by 85%.     

Trends of phosphorus, nitrogen and chlorophyll a concentrations in Finnish rivers and lakes in 1975–2000

During recent decades the amounts of nutrients discharged to Finnish surface waters have markedly decreased. This has been achieved by considerable investments in water protection, which were made mainly to improve municipal and industrial wastewater purification. We investigated whether these water protection measures have decreased phosphorus and nitrogen concentrations in Finnish rivers and lakes. In addition, possible trends in chlorophyll a concentrations in lakes were studied. The data consisted of a total of over 68 000 monitoring results of 22 rivers and 173 lakes (or sub-basins of lakes) with different types of catchment areas. The study period covered the years 1975–2000 and the non-parametric Kendall Tau b and Seasonal Kendall tests were applied for detecting trends. Decreasing nutrient concentration trends were typical in many lakes and rivers earlier polluted by municipal and industrial wastewaters. Increasing nutrient concentration trends were common in smaller rivers and lakes receiving diffuse loading from agriculture. The results show that the investments directed towards wastewater purification have effectively improved the quality of Finnish inland waters. However, no clear effects of decreasing non-point loading were found. Thus, more effective measures should be directed towards decreasing non-point source loading.     

Development and application of an automated subcatchment generator for SWMM using open data

An open source subcatchment generator program was developed for the Stormwater Management Model (SWMM) to automate tedious stages in the model construction process. The generator divides the investigated area into subcatchments using a uniform computation grid and connects the grid cells together and to the underlying stormwater network. The system was tested by applying it to two small urban catchments with different fractions of impervious surfaces in Helsinki, Finland, using mostly openly available data. The simulated discharge results were compared to measured data and to results obtained from manually built models. The proposed system significantly accelerated the setup of a SWMM modelling project, as the routing between the subcatchments as well as the subcatchment slopes and flow widths were directly derived from the computation grid. Automatically generated and manually constructed SWMM models produced discharge results that differed only slightly from each other.