溶胶-凝胶法制备MgxZn1-xO纳米材料

以硝酸锌(Zn(NO3)2·6H2O)、柠檬酸(C6H8O7·H2O)为主要原料,采用改进的溶胶一凝胶法合成了纳米ZnO.在此基础上,添加硝酸镁(Mg(NO3)2·6H2O)合成了MgxZn1-xO.利用X-射线衍射(XRD)、扫描电子显微镜(SEM)表征分析了煅烧温度和Mg掺杂量对产物的相组成及显微形貌的影响.结果表明,x≤10at%时,MgxZn1-xO属于六方纤锌矿结构,当x≥20at%时,MgxZn1-xO中除了具有属于六方纤锌矿结构的ZnO以外还有属于NaCl结构的MgO晶相存在.随煅烧温度的升高,MgxZn1-xO纳米颗粒逐渐长大.     

Attraction to Herbivore-induced Plant Volatiles by the Host-foraging Parasitoid Fly <Emphasis Type="Italic">Exorista japonica</Emphasis>

Responses of the tachinid fly Exorista japonica Townsend to odors from corn plants infested with the fly’s host, the larvae of the noctuid moth Mythimna separata (Walker), were examined in a wind tunnel. Naïve female flies showed a higher rate of landing on M. separata-infested corn plants from which the host larvae had been removed than on artificially damaged or intact corn plants. When paper impregnated with a solution of headspace volatiles collected from host-infested plants was attached to intact plants, females landed on the plants at a high rate. Females also responded to intact plants to which had been attached with paper impregnated with a synthetic blend of nine chemicals identified previously in host-infested plants. There was an optimum concentration of the synthetic blend for the females’ landing. Of the nine chemicals identified previously, four [(E)-4,8-dimethyl-1,3,7-nonatriene, indole, 3-hydroxy-2-butanone, and 2-methyl-1-propanol] released only by host-infested plants were classified as a host-induced blend. The other five [(Z)-3-hexen-1-yl acetate, (E)-2-hexenal, hexanal, (Z)-3-hexen-1-ol, and linalool] were classified as a non-specific blend released not only by infested plants but also by artificially damaged or intact plants. In the wind tunnel, E. japonica females did not respond to intact plants to which paper containing a solution of non-specific blend or host-induced blend was attached. However, they showed a high level of response to a mixture of the non-specific and host-induced blends. These results indicate that naïve E. japonica use a combination of non-specific and host-induced blends as an olfactory cue for locating host-infested plants.     

Preparation and Characterization of Highly Fluorescent, Glutathione-coated Near Infrared Quantum Dots for in Vivo Fluorescence Imaging

Fluorescent probes that emit in the near-infrared (NIR, 700–1,300 nm) region are suitable as optical contrast agents for in vivo fluorescence imaging because of low scattering and absorption of the NIR light in tissues. Recently, NIR quantum dots (QDs) have become a new class of fluorescent materials that can be used for in vivo imaging. Compared with traditional organic fluorescent dyes, QDs have several unique advantages such as size- and composition-tunable emission, high brightness, narrow emission bands, large Stokes shifts, and high resistance to photobleaching. In this paper, we report a facile method for the preparation of highly fluorescent, water-soluble glutathione (GSH)-coated NIR QDs for in vivo imaging. GSH-coated NIR QDs (GSH-QDs) were prepared by surface modification of hydrophobic CdSeTe/CdS (core/shell) QDs. The hydrophobic surface of the CdSeTe/CdS QDs was exchanged with GSH in tetrahydrofuran-water. The resulting GSH-QDs were monodisperse particles and stable in PBS (phosphate buffered saline, pH = 7.4). The GSH-QDs (800 nm emission) were highly fluorescent in aqueous solutions (quantum yield = 22% in PBS buffer), and their hydrodynamic diameter was less than 10 nm, which is comparable to the size of proteins. The cellular uptake and viability for the GSH-QDs were examined using HeLa and HEK 293 cells. When the cells were incubated with aqueous solutions of the GSH-QDs (10 nM), the QDs were taken into the cells and distributed in the perinuclear region of both cells. After 12 hrs incubation of 4 nM of GSH-QDs, the viabilities of HeLa and HEK 293 cells were ca. 80 and 50%, respectively. As a biomedical utility of the GSH-QDs, in vivo NIR-fluorescence imaging of a lymph node in a mouse is presented.     

Effect of CNTs on Activation Volume and Mobile Dislocation Exhaustion Rate of CNTs/Al under Compression Loading

In this study, stress relaxation compression tests were performed to investigate the strain rate sensitivity, activation volume and mobile dislocations in carbon nanotubes/aluminum (CNTs/Al) composites. The results reveal that, with the addition of CNTs, the strain rate sensitivity of CNTs/Al increased. Meanwhile, a smaller V^* of CNTs/Al compared with pure Al was attributed mainly to the CNT-Al interfaces and partly to the increased forest dislocations cutting activities in grain interior, which was related to the tendency of short ranges order formation during plastic deformation. The incorporation of CNTs also improved the dislocation storage capability and reduced the dislocation velocity, leading to a lower mobile dislocation exhaustion rate.     

Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.     

Specialist Leaf Beetle Larvae Use Volatiles from Willow Leaves Infested by Conspecifics for Reaggregation in a Tree

Young, gregariously living larvae of the willow leaf beetles Plagiodera versicolora are known to exhibit characteristic aggregation-dispersion-reaggregation behavior and local fidelity to a host tree. In this study, we investigated whether plant volatiles induced by feeding P. versicolora larvae were involved in the reaggregation behavior. Under laboratory conditions, we conducted dual-choice bioassays and found that the first and second instars discriminated between volatiles from leaves infested by larvae and volatiles from uninfested leaves. The discriminative behavior was dependent on both the time leaves were infested and the age of discriminating larvae. First and second instars preferred odor from 1-d-infested leaves to odor from uninfested leaves, whereas third instars (solitary stage) did not discriminate between these volatile blends. Odor from 2-d-infested leaves was preferred to odor from 1-d-infested leaves by first instars, whereas odor from leaves infested for 3 d was not attractive to these very young larvae. Neither was odor of leaves infested for 1 d and then left uninfested for 1 or 2 d attractive to young larvae. The data suggest that the first and second instars use volatiles from a leaf newly infested by conspecific larvae as one of the reaggregation cues. We detected several herbivore-induced compounds in the headspace of the attractive leaves. Among those, a mixture of synthetic (E)-β-ocimene, (Z)-β-ocimene, allo-ocimene, and linalool was found to attract the larvae.     

Synthesis and hydrophilic property of polypropylene-graft-poly(polyethylene glycol-methacrylate) (PP-g-P(PEGMA))

Polypropylene-graft-poly(polyethylene glycol-methacrylate) (PP-g-P(PEGMA)), which is a hydrophobic-hydrophilic graft copolymer, was synthesized by a combination of an atom transfer radical polymerization (ATRP) of PEGMA with brominated polypropylene (PP-Br), which was synthesized from PP-OH prepared by metallocene-catalyzed copolymerization. Its structure was confirmed by ¹H NMR and GPC analyses. Transmission electron microscope (TEM) micrographs of PP-g-P(PEGMA) revealed the nanometer level microphase-separation morphology between the PP segment and the P(PEGMA) segment. The obtained PP-g-P(PEGMA) showed water-absorbing property as well as thermostability.     

Predator Avoidance by Phytophagous Mites is Affected by the Presence of Herbivores in a Neighboring Patch

When predators invade a leaf patch inhabited by herbivores, the herbivores disperse to a neighboring predator-free leaf patch, thus escaping from the predators. However, the neighboring patch might already be used by con- or heterospecific herbivores. We used laboratory bioassays to examine whether perception of odor from con- or heterospecific competitors on a neighbored lima bean leaf patch influences dispersal behavior of the herbivorous mite Tetranychus urticae when attacked by predatory mites Phytoseiulus persimilis. The dispersal rates of T. urticae that perceived odors from leaf patches infested by conspecifics or cowpea aphids (Aphis craccivora) did not differ from the control (the dispersal rate of T. urticae that perceived odor from uninfested leaf patches). By contrast, the dispersal rate of T. urticae was reduced when they perceived odors from leaf patches that were currently or had previously been infested by larvae of the common cutworm (Spodoptera litura). Previous herbivory by S. litura larvae induced resistance in leaf patches to T. urticae as indicated by the reduced number of eggs laid by T. urticae. Our results are discussed with respect to the feeding behavior of the tested competitors of T. urticae and the impact of the plant and arthropod community on the dispersal behavior of these mites.     

Thermal conduction theoretical analysis of temperature distribution during multiple-electrode submerged arc welding

In recent years, in order to reduce the costs of transportation and construction of pipelines, which are often constructed using multiple-electrode submerged arc welding (SAW), higher joint performance is required. Therefore, there has arisen the need to understand theoretically and control appropriately metallurgical and mechanical characteristics in heat-affected zone (HAZ), which has a significant influence on the strength and toughness of welded joints. Commonly, metallurgical phenomena in HAZ are evaluated based on the highest temperature and the cooling rate. Therefore, in order to control metallurgical and mechanical characteristics in HAZ by means of the welding conditions, evaluating the temperature distribution and the temperature history near the melted zone is essential. However, a detailed investigation of the temperature distribution for multiple-electrode SAW has not yet been carried out enough. In this study, in order to investigate the temperature distribution and histories during multiple-electrode SAW, the experimental results are compared with the theoretical results. In the theoretical analysis, the temperature rise equation in multiple heat sources welding is developed using the method of summation. Furthermore, on temperature distribution during welding, the effects of multiple heat sources, such as the number of heat sources and the distance between each electrodes, are considered quantitatively through the thermal conduction theoretical analysis. As the result, the distance between lead heat source and final heat source primally influences the area with the difference between a single heat source welding and multiple heat sources welding. Based on the results, it is expected to control temperature distribution near melted zone by more appropriate heat input characteristics, which is depended on heat source arrangement.     

Ziegler-Natta/茂金属复合催化剂聚合性能的研究

制备了Ziegler-Natta/茂金属复合(Z-M)催化剂,用SEM技术对其形貌进行了表征,在10L丙烯液相本体聚合模试装置上对Z-M催化剂的氢调敏感性进行了评价。通过一段丙烯本体均聚、二段乙烯-丙烯近恒温恒压气相共聚模拟Spheripol-Ⅱ工艺制备了系列聚丙烯(PP)釜内合金;考察了二段共聚时的聚合反应动力学、乙烯与丙烯配比(n(C3)∶n(C2))对PP釜内合金性能的影响。实验结果表明,在一段均聚时Z-M催化剂具有较好的氢调敏感性,得到的均聚PP粒子具有较好的流动性;在二段共聚时,Z-M催化剂能在较长的共聚时间内保持较平稳、较高的共聚活性,改变n(C3)∶n(C2)时PP釜内合金中乙丙橡胶的质量分数可调(7.19%~10.75%),熔体流动速率(10min)可调(14.0~26.5g);n(C3)∶n(C2)对合金弯曲模量的影响不大;当n(C3)∶n(C2)=1.7时制备的PP釜内合金具有最大的冲击强度(92.9J/m)。