Study of the PM Gas-Phase Filter Artifact Using a Setup for Mixing Diesel-Like Soot and Hydrocarbons

The filter artifact is a significant source of error in gravimetric measurements of particulate matter (PM) exhaust. However, only a few studies on the subject exist. Results from these studies show a large discrepancy mainly because the experiments were performed using real diesel vehicle exhaust with varying exhaust composition. In this study, a setup for mixing diesel-like soot and hydrocarbon vapor was constructed for generating a stable exhaust aerosol with adjustable composition. The particle size distribution of the diesel-fueled soot generator (GMD [geometric mean diameter] adjustable between 27 and 164 nm) was found to represent “real” exhaust particulate emission. This setup was applied for studying the filter artifact on Teflon-coated glass fiber filters using pentadecane as the hydrocarbon vapor. Experiments were performed using particle and hydrocarbon concentrations of 130–700 μg/m³ and 10–12 ppm, respectively. It was found that the particle concentration of the aerosol affects the filter artifact. At lower particle concentrations, more hydrocarbon adsorption was detected. In the absence of particles, the adsorption was highest. Furthermore, filter soot load, corresponding to 0.13%–0.66% of the clean filter mass, was found to affect adsorption. Sooty filters adsorbed less vapor than clean filters. However, increasing the soot load resulted in more adsorption. Moreover, it was found that the backup filter serves as a reasonable estimate of the filter artifact only for low particle concentrations and filter soot loads. These results indicate that the filter soot load is an important parameter influencing the filter artifact, and therefore, it should be considered when performing gravimetric sampling. The setup was proven to be a unique tool for quantitative studies of the filter artifact.

Copyright 2012 American Association for Aerosol Research     

Measuring the Size Distribution of Atmospheric Organic and Black Carbon Using Impactor Sampling Coupled with Thermal Carbon Analysis: Method Development and Uncertainties

A method for determining the mass size distribution of organic and black carbon (OC and BC) in atmospheric aerosols is introduced. The method relies on a particle sampling with 2 parallel size-segregating devices, a 12-stage Small Deposit area low pressure impactor (SDI) and a virtual impactor (VI), and the subsequent analysis of the samples with thermal and thermal-optical methods, respectively. The method development revealed that SDI is, like other sampling methods, susceptible to serious sampling artifacts and OC pyrolysis during thermal analysis. However, some of the SDI's limitations can be overcome by parallel VI measurements. The good correlation between the SDI and the VI data for most of the samples collected here indicates that under most conditions, the lack of the pyrolysis correction for the SDI samples does not cause significant errors in the OC/BC split. Valuable features of this method are that it offers a good size resolution in both sub- and supermicron size fractions, indicates if there has been serious positive or negative artifacts for OC during sampling, reveals if the samples have been affected by OC pyrolysis during thermal analysis, and provides semiquantitative means by which the OC and BC size distributions can be corrected for the samples being affected by OC pyrolysis. Application of the method to real atmospheric samples is demonstrated, and the major areas requiring further research and/or method development are identified.     

Analysis of diastereomeric DAG naphthylethylurethanes by normal-phase HPLC with on-line electrospray MS

Normal-phase HPLC resolution of sn-1,2(2,3)- and x-1,3-DAG generated by partial Grignard degradation from natural TAG was carried out with both (R)-(−) and (S)-(+)-1-(1-naphthyl)ethylurethane derivatives. The diastereomeric sn-1,2- and sn-2,3-DAG derivatives were resolved using two Supelcosil LC-Si (5 μm, 25 cm × 4.6 mm i.d.) columns in series and an isocratic elution with 0.37% isopropanol in hexane at a flow rate of 0.7 mL/min. The DAG were detected by UV absorption at 280 nm and were identified by electrospray ionization MS in the positive ion mode following postcolumn addition of chloroform/methanol/30% ammonium hydroxide (75∶24.5∶0.5, by vol) at 0.6 mL/min. Application of the method to a stereospecific analysis of the molecular species of TAG of rat VLDL showed that the TAG composition of VLDL circulating under basal conditions differs markedly from that of VLDL secreted by the liver during inhibition of serum lipases. The inhibition of serum lipases resulted in a significant proportional decrease in 16∶0 and PUFA and an increase in 18∶0 and oligoenoic FA in the sn-1-position, whereas the FA compositions in the sn-2- and sn-3-positions were much less affected.     

Dietary Fat in Relation to Erythrocyte Fatty Acid Composition in Men

Erythrocyte membrane fatty acid (EMFA) composition is used in the validation of food frequency questionnaires (FFQ) and the evaluation of dietary fat quality. In this cross-sectional study we aimed to investigate associations of diet with EMFA. Altogether, 1,033 randomly selected Finnish men, aged from 47 to 75 years filled in a FFQ and their EMFA composition was analyzed. Marine polyunsaturated fatty acid (PUFA) intake correlated positively with erythrocyte eicosapentaenoic and docosahexaenoic acids (r _s = 0.415 and r _s = 0.340, respectively, P < 0.001) and inversely with all n-6 PUFA analyzed (P < 0.001). PUFA intake from spreads and cooking fats correlated positively with alpha-linolenic (ALA), linoleic (LNA) and nervonic acids (r _s = 0.229, r _s = 0.160 and r _s = 0.143, respectively, P < 0.001). Milk fat intake was associated with myristic and behenic acids (r _s = 0.186 and r _s = 0.132, respectively P < 0.001). Butter users had lower ALA and LNA proportions (mol%) than non-users (0.16 ± 0.04 vs. 0.19 ± 0.05, P < 0.001 and 7.77 ± 1.02 vs. 8.12 ± 1.11, P = 0.001). Higher PUFA intake from meat was related to decreased long-chain n-3 (P < 0.001) and increased n-6 PUFA (P < 0.001) proportions. In conclusion, EMFA composition reflects particularly well the intakes of n-3 PUFA, whereas other associations remained lower. Yet, all main sources of dietary fat were related with EMFA. The dietary effect on the nervonic acid proportion was confirmed.     

Material-related losses of natural rubber composites with surface-modified nanodiamonds

Dielectric elastomer generators (DEGs) offer a solution for the growing sustainable energy needs. Despite the active research on DEGs, currently used materials do not possess the required properties to achieve the full potential performance of such generators, thus, limiting an economical attractiveness of DEGs. Therefore, tailor-made materials for DEGs are in demand. Customizing the natural rubber recipe allows both dielectric and mechanical loss reduction, while the addition of nanodiamonds lowers the stress relaxation and hysteresis loss even further. The effect is most pronounced after chemical modification of nanodiamonds with silane coupling agents. Moreover, such modified nanodiamonds show less dielectric losses compared to unmodified nanodiamonds and allow reducing the dynamic loss tangent of the compound. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48629.     

Vegetable fillers for electric stimuli responsive elastomers

Dielectric elastomer actuators (DEAs) have been studied widely in recent years for artificial muscle applications, but their implementation into production is limited due to high operating voltages required. The actuation behavior of dielectric elastomer under an applied electric field is predicted by Maxwell's pressure and thickness strain equations. According to these equations, the best electromechanical response is achieved when the relative permittivity is high and elastic modulus is low. The potential source for additives increasing the relative permittivity of rubbers can be vegetable powders that have much higher dielectric constant than common elastomers. In the present research, the dielectric and actuation properties of polyacrylate rubber (ACM) were studied after the addition of different vegetable‐based fillers such as potato starch, corn starch, garlic, and paprika. The results were compared to ACM filled with barium titanate. The compounds containing vegetable fillers showed higher relative dielectric permittivity at 1 Hz frequency than the compounds containing barium titanate due to higher interfacial polarization. The actuation studies showed that lower electric fields are required to generate certain actuation forces when the starches and garlic are used in the rubber instead of barium titanate. Therefore, the vegetable‐based fillers can be used to improve actuation performance of DEAs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45081.     

Optimized laser processing of calibration blocks for grinding burn detection with Barkhausen noise

Calibration samples for the Barkhausen noise (BN) method were produced with laser processing. A planet gear wheel used for production quality control was subjected to laser irradiation to verify the BN sensor output. Different samples were found to respond similarly to the laser processing although the laser parameters needed to be adjusted for different surface qualities separately. The surface optimization for laser processing was studied with different surface qualities of samples. The ground surface was compared with a sandblasted and vibratory ground surface. The ground and sandblasted surfaces were both amenable to the laser processing whereas the vibratory grinding process created inhomogeneous surfaces for laser beam absorption. Laser processing was found to produce uniform changes in the residual stress values in two perpendicular measuring directions. The root mean square value of the BN voltage signal exhibited linear correlations with the values of the residual stress and surface hardness.     

Optical scattering of nanocrystalline Pb(ZrxTi1−x)O3 films

Optical characterization methods, like spectrophotometry at UV–vis-NIR wavelengths and prism-coupler method, were applied to polycrystalline Pb(Zr_xTi_1?x)O₃ thin films at various thicknesses. Thin films were deposited at room temperature by pulsed laser deposition on MgO (1 0 0) substrates and post-annealed at different temperatures. X-ray diffraction and atomic force microscopy were used to characterize the crystal structure and surface morphology of the thin films, respectively.Well oscillating transmission with a sharp fall near the absorption edge was found in films with high orientation and low surface roughness. Changes in the surface morphology and crystal orientation were found to modulate optical interference maxima and minima of the transmittance spectra and to increase the width of the TE₀ mode (Δβ ≈ 0.06) indicating an increase in the scattering losses of the films. Single-phase oriented films had sharpest coupling values (Δβ ≈ 0.005) of the TE₀ mode.     

“Plug-up”–a new concept for fabricating SOI MEMS devices

This paper reports a novel process sequence for fabricating micromechanical devices on silicon-on-insulator (SOI) wafers. Among the merits of the described process are its improved immunity to stiction and elimination of conductor metal endurance problems during sacrificial etching in hydrofluoric acid. With this novel process one can controllably embed vacuum cavities within SOI substrates. Further processing of such cavity wafers enables realization of a wide variety of micromechanical devices based on single crystalline silicon or even integrated read-out circuitry.K. Järvi and T. Häkkinen are gratefully acknowledged for the device fabrication. The Finnish National Technology Agency, Okmetic, VTI Technologies, and Micro Analog Systems participated in funding this work. The ultrasonic devices were fabricated in collaboration with Autotank, Oras, Suunto, Vaisala, and Enermet.     

Regulation of receptor-coupling to (multiple) G proteins. A challenge for basic research and drug discovery

G protein-coupled receptors induce intracellular signals via interaction of with cytosolic/peripheral membrane proteins, mainly G proteins. There has been much debate about the mode of interaction between the receptors, G proteins and effectors, their mobility and the ways of determining the specificity of interaction. Additional complexity has been added to system upon the discovery of i) coupling of single receptors to several G proteins and ii) active direction of this by different ligands (stimulus trafficking). These data suggest that the most primary unit in the signal transduction is the receptor complexed with a specific G protein, making the investigation of the mechanism of receptor-G protein selection and interaction even more important. In this review, I will summarize the general knowledge of receptor interaction with G proteins and effectors and the ways of investigating this.