Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.     

Epoxy paint failure in B-52 fuel tanks: Part II. Influence of DIEGME concentration in the fuel on the failure process

A model has been proposed to explain the failure of the original BMS10-39 epoxy paint on upper vertical surfaces in B-52 fuel tanks. The model involves interaction of the paint with DIEGME, a fuel system ice inhibitor (FSII) in jet fuel, that is distilled from the liquid fuel. In this communication, distillation experiments used to support the model are refined to better match the mass transfer of vapor from fuel in a B-52 fuel tank at close to room temperature. The interaction of these lower temperature distillates with the paint affirms the earlier model. On the basis of these experiments it is proposed that paint failure may be controlled or eliminated by reducing the level of DIEGME in the fuel. Proposed changes in military jet fuel composition are detailed.     

A Convenient Synthesis of Some Coumarin Derivatives Using SnCl2 · 2H2O as Catalyst

Some substituted coumarins have been synthesized by von-Pechmann condensation using SnCl₂ · 2H₂O (10 mol %) as catalyst in ethanolic medium. The reactions are simple, easy in handling and environmentally benign.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Generalized model of the formulation of the required composition of pitch-coke mixtures

Known methods of calculating the required compositions of pitch-coke mixtures in producing large graphitized electrodes are not widely used [1, 2]. This may be attributed to the multivariance of the problem, the probabilistic character of the technological operations, the lack of well-founded optimization criteria, and the sensitivity of the characteristics of the product to variation in the parameters of the initial materials and their ratios in the mixture. The only means of solving the problem is physical modeling, taking account of current computer capabilities.     

A fragmentary model of vitreous As<Subscript>2</Subscript>S<Subscript>3</Subscript>

The X-ray scattering intensity curves for vitreous As₂S₃ are experimentally measured using soft (copper) and hard (molybdenum) X rays. The inclusion of all the specific features revealed in the experimental scattering intensity curves makes it possible to obtain the experimental atomic radial distribution function (ARDF) in the ordering range up to ～1 nm. The experimental ARDF is interpreted in the framework of the fragmentary model. A comparison of the experimental ARDF with the model ARDF calculated from the crystal structure data obtained for orpiment demonstrates that the corrugated layers inherent in crystalline As₂S₃ are retained in the glass structure but the characteristic interlayer interatomic distances are absent. The layers are joined together through the As₄S₅ molecular clusters. Microcrystals consisting of several unit cells are absent in the glass structure, which involves only the structural fragments of both crystalline analogs. One of the possible variants of their joining is proposed.     

Design Techniques of CMOS Ultra-Wide-Band Amplifiers for Multistandard Communications

This paper presents design techniques of CMOS ultra-wide-band (UWB) amplifiers for multistandard communications. The goal of this paper is to propose a compact, simple, and robust topology for UWB low-noise amplifiers, which yet consumes a relatively low power. To achieve this goal, a common-gate amplifier topology with a local feedback is employed. The first amplifier uses a simple inductive peaking technique for bandwidth extension, while the second design utilizes a two-stage approach with an added gain control feature. Both amplifiers achieve a flat bandwidth of more than 6 GHz and a gain of higher than 10 dB with supply voltages of 1.8-2.5 V. Designs with different metal thicknesses are compared. The advantage of using thick-metal inductors in UWB applications depends on the chosen topology.     

Novel electro-optic properties of epitaxially grown (Pb, La)(Zr, Ti)O3 (PLZT) thin films derived by advanced sol–gel methods

Advanced sol–gel methods using a secondary solvent addition into (Pb, La)(Zr, Ti)O₃ (PLZT) sol–gel solution and a methanol pre-treatment of sapphire substrates are demonstrated. For the secondary solvent addition, the additive affected the crystallinity and electro-optic (EO) property of PLZT films and only methanol addition can improve them. In addition, the methanol pre-treatment is also appeared to be effective to improve film characteristics.

Through these optimizations, epitaxially grown PLZT thin films on r-cut sapphire are obtained and a high Pockels coefficient which is comparable to those of bulk PLZTs is achieved. It is believed that these PLZT thin films are applicable for integrated EO devices and open the door for the future data communication systems.     

Synthesis of polyanilines with pendant fluorescent units

Functionalized polyanilines containing biphenyl, terphenyl, carbazole, anthracene, and 4-n-hexylphenyl moieties were synthesized though the reaction of polyaniline in emeraldine base form with sodium salt of corresponding vinylketoaromatics with quantitative yields. Polymers were characterized with Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and thermogravimetry. The emission characteristics of these polymers in N-methyl-2-pyrrolidone solution were examined. The functionalized polyanilines exhibited an intense green emission.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.