工艺参数及稳定剂抗坏血酸对电沉积NiFeW合金的影响

为获得性能良好的镍铁钨合金镀层,研究了镀液pH 值、温度、电流密度、稳定剂抗坏血酸浓度对镍铁钨合金镀层成分和镀层沉积速率、显微硬度的影响。结果表明: 镀液pH 值对镀层W含量和镀层沉积速率影响较大;镀液温度对镀层沉积速率、镀层成分和镀层硬度影响均较大;随抗坏血酸浓度增加,镀层沉积速率逐渐降低,镀层表面形貌更加粗糙。在镀液pH = 4,温度60 ℃,电流密度4 A/dm2,抗坏血酸浓度3 g /L 时,镀层沉积速率和镀层的显微硬度较高,表面光亮致密,耐蚀性好。     

Electrochemical behavior of copper current collector in imidazolium-based ionic liquid electrolytes

The electrochemical behaviors of copper current collector in 1-alkyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl] imide ionic liquid electrolytes were investigated and compared with that in ethylene carbonate/dimethyl carbonate solutions. Cyclic voltammetry results showed that large oxidation–reduction current of the copper foil appeared in ethylene carbonate/dimethyl carbonate solutions, while a much smaller current in the room temperature ionic liquid electrolytes decreased gradually, indicating that the copper foil was anodically stable. Further study by X-ray photoelectron spectroscopy analysis showed that an unstable product was composed mainly of the carbonate and carbonyl species on the surface of the copper foil after the electrochemical measurement in ethylene carbonate/dimethyl carbonate solutions, leading to the dissolution of the copper foil. While a better passivating film from the reduction of the anions in the room temperature ionic liquid electrolytes covered the surface of copper foil and protected the copper foil from being oxidized even in a higher potential. These results indicate that the use of room temperature ionic liquid electrolytes can improve the stability of copper current collector in the advanced lithium ion batteries.     

Mechanical and physical characteristics of cellulose‐fiber‐filled polyacetal composites

We investigated the mechanical and physical characteristics of composites composed of polyacetal [alternatively called polyoxymethylene (POM)] and cellulose fiber (CelF) derived from wood pulp [10–52 wt % (9.3–50.1 vol %)] without any fiber surface treatment. The modulus, deflection temperature under load, and thermal conduction coefficient of the POM/CelF composites were effectively enhanced with increasing CelF content, and the composites had an advantage of specific modulus compared to glass fiber (GF)‐filled POM. The flexural modulus of POM/CelF 40 wt % (38.2 vol %) was measured to be about 6 GPa, which was comparable to that of POM/GF 20 wt % (12.1 vol %). In the composites, the CelFs were distributed randomly as monofilaments, and the debonding of the interface between the fibers and POM matrices in the fracture faces was confirmed as less by scanning electron microscopy observation. The POM/CelF composites possessed lower specific wear rates than the POM/GF composites, and they had damping behaviors near that of neat POM. No clear dependence of the melt flow index of the base POM on these characteristics was observed, except on Charpy impact strength. The composites studied here were unique in their performance and ability to be designed in accordance with specific demands, and they could be potential replacements for mineral‐filled and GF‐filled POM composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

采用无偏振片反射式LCD及超低功耗驱动技术制造移动显示器件

我们通过对材料和制备条件的精细化处理,生产出一种在低刷新频率下无闪烁和图像迟滞现象的反射式显示器。该显示器的功耗非常低,且可在宽温度范围内工作,是未来移动显示器件的潜力平台。     

RETRACTED ARTICLE: Single-Phase <Emphasis Type="Italic">β</Emphasis>-Zn<Subscript>4</Subscript>Sb<Subscript>3</Subscript> Prepared by a Mechanical Grinding Method

Single-phase β-Zn₄Sb₃ materials were prepared by mechanical grinding (MG). Source materials for the Zn₄Sb₃ ingots were prepared using three different processes after the direct melting of constituent elements. In process 1, the ingot was obtained by quenching the melt in water within an evacuated quartz ampoule. In process 2, the ingot was heat-treated for 100 h at 723 K after process 1. In process 3, the ingot was heat-treated for a total of 200 h in two stages at 723 K and 673 K after process 1. The resultant ingots were mechanically ground and sintered at 623 K by hot pressing. The sintered materials were characterized by x-ray diffraction, differential thermal analysis (DTA), and thermoelectric property measurements. The thermal conductivity of the sintered materials was 0.88 W m⁻¹ K⁻¹ at room temperature, being slightly lower than that reported for the materials prepared by a conventional method. Results indicate that the dimensionless figure of merit of the single-phase β-Zn₄Sb₃ ranged from 1.06 to 1.31 at 573 K.     

Application of microalgae hydrolysate as a fermentation medium for microbial production of 2-pyrone 4,6-dicarboxylic acid

1. Download high-res image (309KB)
2. Download full-size image

     

Return Link Systems for Wireless Mobile Camera Using 42 GHz-Band with Frequency and Space Diversity Techniques

In this paper, return link systems for wireless mobile camera using 42 GHz-band in multipath fading environments are proposed. The return link systems for wireless mobile camera require wireless transmission with high reliability as same as the conventional wired camera systems. The proposed return link systems achieve transmission with high reliability by taking into consideration frequency and space diversity techniques. The proposed systems can be classified as 3 three types of return link systems according to diversity techniques： FD （frequency diversity） systems, SD （space diversity） systems and FD＋SD system （frequency and space diversity）. Computer simulations are carried out in order to confirm the effectiveness of the proposed return link systems. It is confirmed that the proposed three types of return link systems have an advantage about BER performances and effectively exploit frequency and space resources.     

Influence of Particle Size on the Distributions of Liposomes to Atherosclerotic Lesions in Mice

ABSTRACT

In order to confirm the efficacy of liposomes as a drug carrier for atherosclerotic therapy, the influence of particle size on the distribution of liposomes to atherosclerotic lesions in mice was investigated. In brief, liposomes of three different particle sizes (500, 200, and 70 nm) were prepared, and the uptake of liposomes by the macrophages and foam cells in vitro and the biodistributions of liposomes administered intravenously to atherogenic mice in vivo were examined. The uptake by the macrophages and foam cells increased with the increase in particle size. Although the elimination rate from the blood circulation and the hepatic and splenic distribution increased with the increase in particle size in atherogenic mice, the aortic distribution was independent of the particle size. The aortic distribution of 200 nm liposomes was the highest in comparison with the other sizes. Surprisingly, the aortic distribution of liposomes in vivo did not correspond with the uptake by macrophages and foam cells in vitro. These results suggest that there is an optimal size for the distribution of liposomes to atherosclerotic lesions.     

Quantitative coherent anti-Stokes Raman scattering microspectroscopy using a nanosecond supercontinuum light source

We describe and characterize a multiplex CARS microspectroscopic system that uses a nanosecond supercontinuum generated from a photonic crystal fiber and a sub-nanosecond pulse laser. This system has a high spectral resolution (<0.1 cm^?1) and an ultrabroadband spectral coverage (>2500 cm^?1). The estimated spatial resolutions are 0.45 μm (lateral) and 4.5 μm (axial), respectively. This system enables us to obtain CARS spectra and corresponding images in the fingerprint region as well in the CH stretch region. Using this system, we have successfully obtained label-free and multi-mode vibrational images of a yeast cell.     

Creep deformation properties of creep strength enhanced ferritic steels

Creep deformation properties of creep strength enhanced ferritic steels were investigated. Good linear relationships between creep strain vs. time and creep rate vs. time were observed within a transient stage in a double logarithmic plot. It was appropriately expressed by a power law rather than exponential law, logarithmic law and Blackburn’s equation. With decrease in stress, a magnitude of creep strain at the onset of accelerating creep stage decreased from about 2% in the short-term to less than 1% in the long-term. Life fraction of the time to specific strain of 1% creep strain and 1% total strain, to time to rupture tended to increase with decrease in stress. A time to 1% total strain, that is a parameter for design of high temperature components, was observed in the transient creep stage in the short-term regime, however, it shifted to the accelerating creep stage in the long-term regime. Difference in stress dependence of the minimum creep rate was observed in the high- and low-stress regimes with a boundary condition of 50% of 0.2% offset yield stress. Stress dependence of the minimum creep rate in the high stress regime was equivalent to a strain rate dependence of flow stress observed in tensile test, and a magnitude of stress exponent, n, in the high stress regime decreased with increase in temperature from 20 at 550°C to 10 at 700°C. On the other hand, n value in the low stress regime was about 5, and creep deformation in the low stress regime was considered to be controlled by dislocation climb.