Current control of a PWM power amplifier by an approximate 2-degree-of-freedom digital controller

There is a need for robust current control of a pulse width modulation (PWM) power amplifier whose transient response characteristics do not deteriorate with extensive load changes and/or direct-current power supply voltage changes. In this article, we propose a digital robust controller with bumpless mode switching to control the current of a PWM power amplifier to satisfy the demands and extend the range of an inductive load width. It is necessary to measure the value of the load in order to implement this bumpless mode switching automatically depending on the load range. Therefore, a method of estimating the inductive load is shown. The bumpless mode switching is automatically performed by estimating an inductive value without specifying the value of the inductive load beforehand. That is, the value of the inductive load is estimated during the DDC execution, and the control mode is automatically switched bumplessly according to this estimated value. A digital controller equipped with inductance estimation and bumpless mode switching is realized by a DSP. Some experiments show that the digital controller with the proposed bumpless mode switching can satisfy larger specifications.     

Fatigue strength correction factors for carbon and low-alloy steels in oxygen-containing high-temperature water

Strain-controlled fatigue tests were conducted on carbon and low-alloy steels in high-temperature water containing controlled amounts of oxygen, in order to determine quantitatively the reduction of fatigue strength due to factors such as the strain rate and the environmental testing conditions such as temperature and dissolved oxygen content. For each of these factors, the effect on fatigue strength was separately quantified and parametric equations were derived with reference to the basic fatigue curve obtained in air at room temperature. Using the formulas thus obtained, generalized expressions for predicting the expected fatigue life of a given material under specified combinations of strain amplitude and environmental conditions were deduced. Based on these generalized expressions, “fatigue strength correction factors for environmental effectsrd are proposed, which can be conveniently used in combination with the design fatigue curve given in the ASME Boiler and Pressure Vessel Code, Section III to account for fatigue strength reduction under severe service conditions.     

Influence of one bout of intensive running on lymphocyte micronucleus frequencies in endurance-trained and untrained men

This clinical investigation was designed to determine the effect of changes in loading patterns on left ventricular (LV) relaxation when heart rate was maintained constant. Not only were changes noted in total load or time in which load is changed, but also the contour of the ascending aortic systolic pressure wave. Twenty patients were studied. LV and ascending aortic pressure were measured by a multisensor catheter under baseline conditions (C) and after an intravenous injection of 2.5 microg angiotensin (A) and sublingual administration of 0.3 mg nitroglycerin (N). A bipolar pacing catheter was placed in the right atrium to maintain a constant heart rate throughout the protocol. The augmentation index (AI), which characterizes the contour of the ascending aortic systolic pressure wave, was defined as the ratio of the height of the late systolic shoulder/peak to that of the early systolic shoulder/peak in the pulse. The rate of isovolumic LV pressure decline was calculated as a time constant (Tau). Ascending aortic systolic pressures (mmHg) were 127+/-29 (C), 158+/-20 (A) and 109+/-15 (N). AI were 1.61+/-1.14 (C), 2.08+/-1.11 (A) and 1.27+/-1.14 (N). Tau values (msec) were 49+/-4 (C), 54+/-4 (A) and 45+/-5 (N). Tau was prolonged proportionally with increasing AI (p<0.001, r=0.64). It was concluded that late systolic pressure augmentation in the ascending aorta is one important factor that influences the rate of isovolumic left ventricular pressure decline in humans.     

Experiments on pilot symbol-assisted coherent multistageinterference canceller for DS-CDMA mobile radio

A three-stage coherent multistage interference canceller (COMSIC) employing pilot symbol-assisted (PSA) channel estimation for replica generation of multiple access interference (MAI) is implemented and its performance in the presence of frequency selective multipath fading is experimentally evaluated by a multipath fading simulator. A fast transmission power control (TPC) method suitable for COMSIC is also proposed, in which the signal-to-interference plus background noise power ratio (SIR) at the matched filter (MF) based RAKE receiver is measured to achieve a short TPC delay and the target signal-to-interference ratio value is compensated by an outer loop so that the measured block error rate (BLER) is equal to the prescribed target value. The experimental results show that as expected the COMSIC satisfactorily reduces the MAI even when the number of active users is equal to the spreading factor in a multipath fading environment, and thus, improves the bit error rate (BER) performance in a multiuser environment. The results also show that the proposed fast TPC method with a two-slot delay associated with COMSIC works satisfactorily and the combination of COMSIC and fast TPC significantly decreases the transmission power of a mobile station (required transmission power of a mobile station with COMSIC at the average BER of 10^-3 is decreased by approximately 2.0 (3.0) dB compared with the MF-based RAKE receiver with (without) antenna diversity reception). This extends the cell coverage, battery life, and increases the system capacity in the reverse link     

Principle and basic characteristics of linear synchronous motor with half‐wave rectified self excitation

This paper presents the principle and basic characteristics of a novel linear synchronous motor based on “half‐wave rectified self excitation principle.” The field winding is short circuited through a diode and the armature winding consists of conventional three‐phase windings. If the amplitude of the balance three‐phase currents is modulated by an alternating wave with bias frequency, the produced magnetomotive force pulsates at the bias frequency and moves at the synchronous velocity. This pulsating magnetomotive force induces the electromotive force with a bias frequency in the field winding. The field excitation is obtained by rectifying the electromotive force with the diode in the field winding. In this paper, the authors design and build an experimental machine and confirm its basic characteristics. They also deduce the performance equations and investigate the thrust ripple reduction. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(1): 82–90, 2008; Published online in Wiley InterScience ( www. interscience.wiley.com ). DOI 10.1002/eej.20684     

Photoconductivity of n-type semiconductor nanoparticle-doped poly(N-vinylcarbazole) films

TiO₂, CdS and ZnS nanoparticles that disperse stably in organic solvents are synthesized. Poly(N-vinylcarbazole) films doped with the n-type semiconductor nanoparticles are prepared with a cast method. The films exhibit a transient photocurrent when irradiated by a light pulse and act such as a diode when AC voltage is applied under continuous illumination. The transient photocurrent response and diode-like properties are significantly different depending on the kind of the nanoparticles and their amounts. The films doped with TiO₂ and CdS nanoparticles increase the transient photocurrent at lower doped amounts, which is remarkable for TiO₂-doped films. Time of flight analysis of the transient photocurrent shows that mobility of hole in PVK increases with increase in the amount of CdS and TiO₂. From the studies on the diode-like properties, the current increase at lower dopant concentration is concluded to be due to increase in the amount of holes by an electron transfer from PVK to the photo-excited nanoparticles. At higher doping with CdS nanoparticles, main charge carrier of the films is found to change from holes to electrons.     

Effect of wall slip on blown film thickness distribution

One of the most important materials for blown film is high‐density polyethylene (HDPE) with wide molecular weight distribution. First, we computed a wall stress at the entrance of a spiral groove in a particular die during blown film processing on a particular condition, to which a similar condition is widely utilized in a film works. The computed value is about 170 kPa, while the HDPE melt slips at die wall at stresses above approximately 50 kPa. The stress of 170 kPa is sufficiently large for the slip occurrence of the melt. Then, we investigated the effects of wall slip and melt visosity on film thickness distribution in the circumferential direction; the distribution tends to decrease with decreasing wall slip and melt viscosity. This tendency is explained by considering flow distribution in a spiral mandrel die and polymer melt flow characteristics.     

Intermittent hydronephrosis. A clinical study in 23 pediatric patients

BACKGROUND: It is difficult to diagnose intermittent hydronephrosis and to decide the indication of surgical intervention. We investigated 23 cases of intermittent hydronephrosis. METHODS: From 1978 to 1995, a total of 23 patients were diagnosed as intermittent hydronephrosis in our institution. We inspected their clinical features and treatment which had been performed to them. RESULTS: Our study comprised 21 boys and 2 girls, whose mean age was 6 year old. Their chief complaint was intermittent flank pain (left: 21, right: 1, bilateral: 1) accompanied with gross hematuria (30%) and vomiting (39%). When they were asymptomatic, an excretory urogram revealed only mild pelvic dilatation without calyceal distension and kinking of ureteropelvic junction. Split renal function study by RI showed no difference between the affected side and the normal side except one case. When pelvic or calyceal enlargement was confirmed on ultrasonography while they were symptomatic, surgery was indicated. Surgery was performed in 17 cases (74%) including dismembered pyeloplasty in 14 cases, resection of aberrant vessel in 1, relocation of lower pole renal vessel in 1 and nephrectomy in 1. In surgical and histological view points, intrinsic stenosis was seen in 10 cases, extrinsic obstruction caused by aberrant vessels was seen in 4 and ureteral polyp was seen in 3 (bilateral polyp in 1 case). CONCLUSION: They had no more symptoms after operation. Of 23 among followed up cases without surgery, we experienced 2 cases unexpectedly advancing irreversible hydronephrotic change after the last attack, 1 case of gradually progressing hydronephrotic change and 1 case of severe renal dysfunction after many attacks. Therefore intermittent hydronephrosis should be followed up carefully.