Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

High temperature catalytic combustion of methane and propane over hexaaluminate catalysts: NOx emission characteristics

Several hexaaluminate-related materials were prepared via hydrolysis of alkoxide and powder mixing method for high temperature combustion of CH₄ and C₃H₈, in order to investigate the effect of the concentration of the fuels, O₂ and H₂O on NO_x emission and combustion characteristics. Among the hexaaluminate catalysts, Sr_0.8La_0.2MnAl₁₁O₁₉₋ prepared by the alkoxide method exhibited the highest activity for methane combustion and low NO_x emission capability. NO_x emission at 1500 °C was increased linearly with O₂ concentration, whereas water vapor addition decreased NO_x emission in CH₄ combustion over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst. In the catalytic combustion of C₃H₈ over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst, the amount of NO_x emitted was raised in the temperature range between 1000 and 1500 °C when the C₃H₈ concentration increased from 1 to 2 vol.%. It was found that NO_x emission in this temperature range was reduced effectively by adding water vapor.     

Biocomposites Made from Short Abaca Fiber and Biodegradable Polyesters

Natural fiber‐reinforced biodegradable polyester composites were prepared from biodegradable polyesters and surface‐untreated or ‐treated abaca fibers (length ca. 5 mm) by melt mixing and subsequent injection molding. Poly(butylene succinate)(PBS), polyestercarbonate (PEC)/poly(lactic acid)(PLA) blend, and PLA were used as biodegradable polyesters. Esterifications using acetic anhydride and butyric anhydride, alkali treatment, and cyanoethylation were performed as surface treatments on the fiber. The flexural moduli of all the fiber‐reinforced composites increased with fiber content. The effect of the surface treatment on the flexural modulus of the fiber‐reinforced composites was not so pronounced. The flexural strength of PBS composites increased with fiber content, and esterification of the fiber by butyric anhydride gave the best result. For the PEC/PLA composites, flexural strength increased slightly with increased fiber content (0–20 wt.‐%) in the case of using untreated fiber, while it increased considerably in the case of using the fiber esterified by butyric anhydride. For the PLA composite, flexural strength did not increase with the fiber reinforcement. The result of soil‐burial tests showed that the composites using untreated fiber have a higher weight loss than both the neat resin and the composites made using acetylated fiber.

Flexural modulus of PBS composites as a function of fiber content.     

Enhancing low-temperature energy harvesting by lead-free ferroelectric Ba(Zr0.1Ti0.9)O3

The energy-harvesting ability of the lead-free ferroelectric Ba(Zr,Ti)O₃ was investigated and greatly enhanced using the Kim novel electrothermodynamic cycle for low-temperature application. Ba(Zr,Ti)O₃ was synthesized with a Zr:Ti ratio of 10:90 (BZT10) by hot-press sintering, which exhibited a mix relaxor-ferroelectric behavior. For power generation using the Kim cycle with low and high temperatures of T_L = 25°C, T_H = 120°C, the most optimized temperature pattern occurred for a heating time of 12.5 s and a cooling time of 22.5 s. Under these conditions, the electric field increased during the novel isodisplacement process, and the displacement variation in the isoelectric step reached the highest value and maximized the BZT10 cycle loop area. Applying these conditions while lowering T_L to 20°C, an energy density N_D = 504 mJ/cm³ was achieved. This value is the highest obtained energy density in a practical test for lead-free ferroelectric bulk material in the BaTiO₃ family.     

Orientation and Grain Boundary Microstructure of Alumina in Al/Al2O3 Composites Produced by Reactive Metal Penetration

The orientation and grain boundary microstructure of alumina in reactive metal penetration Al/Al₂O₃ composites are studied using orientation imaging microscopy and the results are compared with those of sintered polycrystalline Al₂O₃. The interconnected Al₂O₃ in the composite material is separated by Σ3 boundaries (twins) with a 60° rotation around the [0001] direction. A high frequency (∼100%) of Σ3 coincidence boundaries in composite alumina is remarkable since only ∼12% of boundaries in a sintered polycrystalline Al₂O₃ are of special nature. The coincidence boundaries in the in situ alumina grow in a coherent and faceted manner.     

The physical character of coal char formed during rapid pyrolysis at high pressure

Rapid pyrolysis was conducted in a drop tube reactor using seven coals under various operating conditions. In addition to dense char, porous chars (network char and cenospheric char) were formed by the rapid pyrolysis under certain conditions. Porous char was mainly composed of film-like carbon and skeleton carbon. The pyrolyzed coal char particles were characterized in detail. Morphology and bulk density of porous char were quite different from the dense char formed under the same conditions, but elemental composition and BET surface area were similar to each other. CO₂ gasification reactivity of porous char was lower than dense char in the later gasification stage, and this was ascribed to the low reactivity of skeleton carbon.     

Hydrolytic degradation of poly[(R)-3-hydroxybutyric acid] in the melt

Poly[(R)-3-hydroxybutyric acid] [R-P(3HB)] was hydrolyzed in high-temperature and high-pressure water at the temperature range of 180-300 °C and for a period of 360 min. The formation, racemization, and decomposition of 3-hydroxybutyric acids (3HBs) and molecular weight change of R-P(3HB) were investigated. The highest yield of (R)-3-hydroxybutyric acid (R-3HB), ca. 80%, was obtained at 200 °C in the hydrolytic degradation periods of 240-360 min. Too-high hydrolytic degradation temperature such as 300 °C induced the decomposition and racemization of formed 3HBs, resulting in decreased yield of R-3HB. The hydrolytic degradation of R-P(3HB) proceeds homogeneously and randomly via a bulk erosion mechanism. The molecular weight of R-P(3HB) decreased exponentially without formation of low-molecular-weight specific peaks originating from crystalline residues. The hydrolytic degradation rates in the melt estimated from M_n changes were lower for R-P(3HB) than for poly(l-lactide) (PLLA) in the temperature range of 180-220 °C. The activation energy for the hydrolytic degradation (ΔE_h) of R-P(3HB) in the melt (180-250 °C) was 30.0 kcal mol⁻¹, which is higher than 12.2 kcal mol⁻¹ for PLLA in the melt in the temperature range (180-250 °C). This study reveals that hydrolytic degradation of PHB in the melt is an effective and simple method to obtain (R)-3HB and to prepare R-P(3HB) having different molecular weights without containing the specific low-molecular-weight chains, because of the removal of the effect caused by crystalline residues.     

The Role of a Nonribosomal Peptide Synthetase in l‐Lysine Lactamization During Capuramycin Biosynthesis

Capuramycins are one of several known classes of natural products that contain an l ‐Lys‐derived l ‐α‐amino‐?‐caprolactam (l ‐ACL) unit. The α‐amino group of l ‐ACL in a capuramycin is linked to an unsaturated hexuronic acid component through an amide bond that was previously shown to originate by an ATP‐independent enzymatic route. With the aid of a combined in vivo and in vitro approach, a predicted tridomain nonribosomal peptide synthetase CapU is functionally characterized here as the ATP‐dependent amide‐bond‐forming catalyst responsible for the biosynthesis of the remaining amide bond present in l ‐ACL. The results are consistent with the adenylation domain of CapU as the essential catalytic component for l ‐Lys activation and thioesterification of the adjacent thiolation domain. However, in contrast to expectations, lactamization does not require any additional domains or proteins and is likely a nonenzymatic event. The results set the stage for examining whether a similar NRPS‐mediated mechanism is employed in the biosynthesis of other l ‐ACL‐containing natural products and, just as intriguingly, how spontaneous lactamization is avoided in the numerous NRPS‐derived peptides that contain an unmodified l ‐Lys residue.     

Discovery of a Novel Scaffold as an Indoleamine 2,3‐Dioxygenase 1 (IDO1) Inhibitor Based on the Pyrrolopiperazinone Alkaloid,Longamide B

Indoleamine 2,3‐dioxygenase 1 (IDO1) has emerged as a key target for cancer therapy, as IDO1 plays a critical role in the capacity of tumor cells to evade the immune system. The pyrrolopiperazinone alkaloid longamide B and its derivatives were identified as novel IDO1 inhibitors based on docking studies and small library synthesis. The thioamide derivative showed higher IDO1 inhibitory activity than longamide B, and displayed an activity similar to that of a representative IDO1 inhibitor, 1‐methyl‐tryptophan. These results suggest that the pyrrolopiperazinone scaffold of longamide B could be used in the development of IDO1 inhibitors.     

Preparation of TiO2 thin films using octadecylamine Langmuir-Blodgett films and evaluation of their photocatalytic activity

A study was conducted to demonstrate that nanometer-thick titanium dioxide (TiO(2)) thin films could be prepared by the hydrolysis of titanium potassium oxalate using octadecylamine (ODA) Langmuir-Blodgett (LB) films as templates. The amount of TiO(2) generated in the LB film was found to be proportional to the number of deposited ODA layers, which enables precise control of the TiO(2) film thickness. After heat treatment of the LB films at 300-600°C, the photocatalytic activities of the resulting TiO(2) films were determined from the decomposition of stearic acid cast films when irradiated with UV light for different time periods. Higher photocatalytic activity was observed in TiO(2) films heat treated at lower temperatures.