Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Knowledge-based control and case-based diagnosis based upon empirical knowledge and fuzzy logic for the SBR plant.

Because biological wastewater treatment plants (WWTPs) involve a long time-delay and various disturbances, in general, skilled operators manually control the plant based on empirical knowledge. And operators usually diagnose the plant using similar cases experienced in the past. For the effective management of the plant, system automation has to be accomplished based upon operating recipes. This paper introduces automatic control and diagnosis based upon the operator's knowledge. Fuzzy logic was employed to design this knowledge-based controller because fuzzy logic can convert the linguistic information to rules. The controller can manage the influent and external carbon in considering the loading rate. The input of the controller is not the loading rate but the dissolved oxygen (DO) lag-time, which has a strong relation to the loading rate. This approach can replace an expensive sensor, which measures the loading rate and ammonia concentration in the reactor, with a cheaper DO sensor. The proposed controller can assure optimal operation and prevent the over-feeding problem. Case-based diagnosis was achieved by the analysis of profile patterns collected from the past. A new test profile was diagnosed by comparing it with template patterns containing normal and abnormal cases. The proposed control and diagnostic system will guarantee the effective and stable operation of WWTPs.     

Optically preamplified receiver performance due to VSB filtering for 40-Gb/s optical signals modulated with various formats

Optically preamplified receiver performance according to the vestigial sideband (VSB) filtering has been numerically investigated for 40-Gb/s optical signals modulated with nonreturn-to-zero, duobinary nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed RZ, and duobinary carrier-suppressed RZ formats. The VSB filtering enables the spectral widths of NRZ, duobinary NRZ, and RZ signals to be reduced without severe power penalties at the receiver. On the other hand, carrier-suppressed RZ and duobinary carrier-suppressed RZ signals have no large advantages over VSB filtering because of the characteristics of their signals. Our results suggest that RZ signals are the most suitable modulation format for VSB filtering, without considering the filter loss, because of the tolerance of the intersymbol interference and a large spectral width. However, duobinary NRZ signals are the most suitable modulation format for VSB filtering, considering the filter loss, because of their narrow spectral width.     

Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

隧道挖掘中采用补偿灌浆的实例

在英国伦敦多克兰斯轻便铁路刘易舍姆延长线（DLR－LWE）双隧道掘进工程中，在敏感建筑物下进行了补偿灌浆，以防止隧道开挖引起的过度沉降。但是，过度灌浆也会对隧道下部施加超越。介绍了由隧道掘进承包商所编辑的关于地面和建筑物沉降以及由补偿灌浆引起的隧道衬砌变形的详细现场监测数据。     

Performance engineering and topological design of metro WDM opticalnetworks using computer simulation

This paper demonstrates the use of computer simulation for topological design and performance engineering of transparent wavelength-division multiplexing metropolitan-area networks. Engineering of these networks involves the study of various transport-layer impairments such as amplifier noise, component ripple, chirp/dispersion, optical crosstalk, waveform distortion due to filter concatenation, fiber nonlinearities, and polarization effects. A computer simulation methodology composed of three main simulation steps is derived and implemented. This methodology obtains performance estimations by applying efficient wavelength-domain simulations on the entire network topology, followed by time-/frequency-domain simulations on selected paths of the network and finally Q-budgeting on an identified worst case path. The above technique provides an efficient tool for topological design and network performance engineering. Accurate simulation models are presented for each of the performance impairments, and the computer simulation methodology is used for the design and engineering of a number of actual metro network architectures     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.