HTR-10燃料元件装卸系统冷态调试

10MW高温气冷实验堆（HTR－10）是一座球床堆，由燃料元件装卸系统实现燃料元件的装卸和循环，且不需要停堆，为保证HTR－10的正常运行，燃料元件装卸系统必须安全，可靠，为此，必须对燃料元件装卸系统进行周密，细致的调试试验和验证，本文介绍了燃料元件装卸系统冷调试的主要调试项目，调试方法和调试结果。     

激光起爆与点火系统中光纤连接器

介绍了激光起爆与点火系统中光纤连接器的原理、种类、技术特性及损耗，并对激光起爆与点火系统中光纤连接器的研制动向进行了概括，最后得出一些结论。     

Matrix partial fraction expansions of rational matrices

A general and rigorous derivation is made of a new formula, established recently in the literature, for matrix partial fraction expansion of a rational matrix. The procedure, by use of a minimal Jordan realization of the rational matrix, provides as a byproduct, general expressions for residue matrices in terms of products of columns of the output matrix and rows of the input matrix of the realization.     

第七届中国国际橡胶技术展暨第一届亚洲埃森轮胎展系列报道二:橡胶机械系列报道三:橡胶检测设备

国内主要参展商 1.益阳橡机 益阳橡胶塑料机械集团有限公司在本次展会上,推出了一款GE-5实验室用密炼机,容积5升,啮合型转子,用于橡胶制品、白炭黑、特种胶的混炼.     

MHD simulation of high-current subsonic vacuum arc under different distributed axial magnetic fields

Based on two-temperature magnetic hydrodynamic (MHD) model, the influence of saddle-shaped distributed axial magnetic field (AMF, linearly increases along radial position) and bell-shaped distributed AMF (linearly decreases along radial position) on plasma loss and heat flux density to anode in subsonic high-current vacuum arc (HCVA) is simulated and analyzed. According to the simulation results, the saddle-shaped AMF can more effectively inhibit plasma loss from arc column than that of bell-shaped AMF. Comparisons between simulation results and experimental results further verify the correctness of model and simulation.     

低温等离子体对血管内金属支架的表面改性

生物材料用于人体必须要具备生物相容性。尤其是与血液相接触的材料如血管内支架必须要具备血液相容性。材料的表面特性直接影响血液系统中是否会出现血栓。本文针对金属血管内支架的表面特性、与血液的界面反应以及用于提高血液相容性的低温等离子表面改性进行了简要综述     

离心式高炉鼓风机扩压叶片断裂事故分析及处理

通过高炉鼓风机扩压叶片断裂事故，从化学分析、物理检验，结合使用情况对扩压叶片断裂原因进行了详细分析，并提出了改进措施。     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Characterization of charge trapping in submicrometer NMOSFET's bygate capacitance measurements

Trapping of net positive charge at low gate stress voltage, and of net negative charge at high gate stress voltage, is observed through changes in the gate-to-drain capacitance of the stressed junction. These observations can be explained in terms of electron trapping, hole trapping, and generation of acceptor-like interface states located in the upper half of the bandgap. Channel shortening is also observed and found to exhibit a logarithmic time dependence