Selective and self-validating breath-level detection of hydrogen sulfide in humid air by gold nanoparticle-functionalized nanotube arrays

We demonstrate the selective detection of hydrogen sulfide at breath concentration levels under humid airflow,using a self-validating 64-channel sensor array ba...     

Working conditions in the engine department – A qualitative study among engine room personnel on board Swedish merchant ships

The specific problems associated with the work on board within the merchant fleet are well known and have over the years been a topic of discussion. The work conditions in the engine room (ER) are demanding due to, e.g. the thermal climate, noise and awkward working postures. The work in the engine control room (ECR) has over recent years undergone major changes, mainly due to the introduction of computers on board. In order to capture the impact these changes had implied, and also to investigate how the work situation has developed, a total of 20 engine officers and engine ratings were interviewed. The interviews were semi-structured and Grounded Theory was used for the data analysis. The aim of the present study was to describe how the engine crew perceive their work situation and working environment on board. Further, the aim was to identify areas for improvements which the engine crew consider especially important for a safe and effective work environment. The result of the study shows that the design of the ECR and ER is crucial for how different tasks are performed. Design which does not support operational procedures and how tasks are performed risk inducing inappropriate behaviour as the crew members’ are compelled to find alternative ways to perform their tasks in order to get the job done. These types of behaviour can induce an increased risk of exposure to hazardous substances and the engine crew members becoming injured.     

Resampling Feature and Blend Regions in Polygonal Meshes for Surface Anti-Aliasing

Efficient surface reconstruction and reverse engineering techniques are usually based on a polygonal mesh representation of the geometry: the resulting models emerge from piecewise linear interpolation of a set of sample points. The quality of the reconstruction not only depends on the number and density of the sample points but also on their alignment to sharp and rounded features of the original geometry. Bad alignment can lead to severe alias artifacts. In this paper we present a sampling pattern for feature and blend regions which minimizes these alias errors. We show how to improve the quality of a given polygonal mesh model by resampling its feature and blend regions within an interactive framework. We further demonstrate sophisticated modeling operations that can be implemented based on this resampling technique.     

Spatial distribution of light-induced lipid oxidation in semi-hard yellow cheese as detected by confocal microscopy

The migration of oxidative damage in semi-hard yellow cheese resulting from surface exposure to 436 nm monochromatic light with an intensity of 2.5 × 10¹⁷ quanta min⁻¹ cm⁻² for 0, 5, 10, and 15 min was followed by confocal laser scanning microscopy using labelling with the lipophilic fluorescence ratio probe C₁₁-Bodipy (581/591). From 5 × 5 × 5 mm cubes of cheese exposed to light on one plane 35 μm was sliced off and fluorescence of oxidised and non-oxidised probe recorded simultaneously on the surface of the slice reaching 250 μm inwards from the exposed surface. From the emission of the fluorescence ratio probe light-induced lipid oxidation could be followed with time of exposure to light. The penetration of light inwards in the cheese with time expressed as quanta cm⁻², as calculated from light transmittance at 436 nm determined spectrophotometrically for cheese slices of up to 300 μm thickness, together with light intensity as determined by actinometry, could alone account for the inwards migration of oxidation. Diffusion of radicals seems of less importance for spatial dispersion of light-induced oxidation in semi-hard cheese.     

Controlled-pH tissue cleanup protocol for signal enhancement of small molecule drugs analyzed by MALDI-MS imaging

The limit of detection of low-molecular weight compounds in tissue sections, analyzed by matrix assisted laser desorption ionization mass spectrometry imaging (MALDI-MSI), was significantly improved by employing sample washing using a pH-controlled buffer solution. The pH of the washing solutions were set at values whereby the target analytes would have low solubility. Washing the tissue sections in the buffered solution resulted in removal of endogenous soluble ionization-suppressing compounds and salts, while the target compound remained in situ with minor or no delocalization during the buffered washing procedure. Two pharmaceutical compounds (cimetidine and imipramine) and one new protease inhibitor compound were successfully used to evaluate the feasibility of the pH-controlled tissue washing protocol for MALDI-MSI. Enhancement in signal-to-noise ratio was achieved by a factor of up to 10.     

Implementation of energy-efficient windows in Swedish single-family houses

A questionnaire survey of 1010 homeowners in Jämtland and Västernorrland, which are two counties in central Sweden, was conducted to understand the factors influencing their decision to install energy-efficient windows. We complemented this survey with an interview of 12 window sellers/installers in the county Jämtland. The annual energy cost reduction, age, and condition of the windows were the most important reasons for the window replacement decision. Approximately 80% of the respondents replaced their windows with energy-efficient windows with U-value of 1.2 W/m² K. Condensation problems, perceived higher prices, and lack of awareness about windows with lower U-values were important reasons for non-adoption of more energy-efficient windows. Window sellers/installers have a strong influence on homeowners’ window selection that was indicated by the 97% of homeowners who bought the windows that were recommended to them. Sellers/installers revealed that they did not recommend windows with U-value of less than 1.2 W/m² K because they thought that investing in such windows was not economical and because windows with U-value less than 1.2 W/m² K could cause water condensation on the external surface of window pane.     

The effect of accuracy motivation on anchoring and adjustment: Do people adjust from provided anchors?

Increasing accuracy motivation (e.g., by providing monetary incentives for accuracy) often fails to increase adjustment away from provided anchors, a result that has led researchers to conclude that people do not effortfully adjust away from such anchors. We challenge this conclusion. First, we show that people are typically uncertain about which way to adjust from provided anchors and that this uncertainty often causes people to believe that they have initially adjusted too far away from such anchors (Studies 1a and 1b). Then, we show that although accuracy motivation fails to increase the gap between anchors and final estimates when people are uncertain about the direction of adjustment, accuracy motivation does increase anchor–estimate gaps when people are certain about the direction of adjustment, and that this is true regardless of whether the anchors are provided or self-generated (Studies 2, 3a, 3b, and 5). These results suggest that people do effortfully adjust away from provided anchors but that uncertainty about the direction of adjustment makes that adjustment harder to detect than previously assumed. This conclusion has important theoretical implications, suggesting that currently emphasized distinctions between anchor types (self-generated vs. provided) are not fundamental and that ostensibly competing theories of anchoring (selective accessibility and anchoring-and-adjustment) are complementary. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Fusion Generated Fast Particles by Laser Impact on Ultra-Dense Deuterium: Rapid Variation with Laser Intensity

Nuclear fusion D+D processes are studied by nanosecond pulsed laser interaction with ultra-dense deuterium. This material has a density of 10²⁹ cm^?3 as shown in several previous publications. Laser power is <2 W (0.2 J pulses) and laser intensity is <10¹⁴ W cm^?2 in the 5–10 μm wide beam waist. Particle detection by time-of-flight energy analysis with plastic scintillators is used. Metal foils in the particle flux to the detector remove slow ions, and make it possible to convert and count particles with energy well above 1 MeV. The variation of the signal of MeV particles from D+D fusion is measured as a function of laser power. At relatively weak laser-emitter interaction, the particle signal from the laser focus varies as the square of the laser power. This indicates collisions in the ultra-dense deuterium of two fast deuterons released by Coulomb explosions. During experiments with stronger laser-emitter interaction, the signal varies approximately as the sixth power of the laser power, indicating a plasma process. At least 2 × 10⁶ particles are created by each laser pulse at the maximum intensity used. Our results indicate break-even in fusion at a laser pulse energy of 1 J with the same focusing, in approximate agreement with theoretical results for ignition conditions in ultra-dense deuterium. Radiation loss at high temperature will however require higher laser energy at break-even.     

Challenges when implementing BIM for industry change

Public clients have been identified as drivers of architectural, engineering and construction (AEC) industry change through their implementation of building information modelling (BIM). Yet, little is known of this implementation process and the associated challenges. This study aims to increase the understanding of what intra- and inter-organizational challenges that arise when a large Swedish public infrastructure client implements BIM to change the work practices of the actors in the Swedish AEC industry. The IT business value model allows for understanding the public client’s implementation of BIM as an IT-supported change process and for understanding the associated intra- and inter-organizational challenges. The findings show nine categories of intra- and inter-organizational challenges related to, for example, demanding BIM in procurement and creating incentives for BIM implementation. The findings show that intra-organizational challenges related to a top-down implementation of BIM, while inter-organizational challenges related to a bottom-up implementation. The impact of these challenges on the public client’s ability to drive AEC industry change by implementing BIM is discussed. The findings contribute with the client perspective to studies on BIM implementation and with an increased understanding of the challenges associated with implementing IT-supported change processes.