Molecularly imprinted polymer coatings for open-tubular capillary electrochromatography prepared by surface initiation

Molecularly imprinted polymer coatings were synthesized in fused-silica capillary columns by the use of a surface-coupled radical initiator. The coatings were prepared using either toluene, dichloromethane, or acetonitrile in the prepolymerization mixtures and were 0.15-2 microm thick as determined by scanning electron microscopy. Solvent-dependent differences in appearance were observed. All the molecularly imprinted polymer-based open-tubular capillary columns were able to separate the enantiomers of propranolol by means of electrochromatography. Electrochromatographic performance was found to be dependent on the type of solvent used during the synthesis.     

Controlled-pH tissue cleanup protocol for signal enhancement of small molecule drugs analyzed by MALDI-MS imaging

The limit of detection of low-molecular weight compounds in tissue sections, analyzed by matrix assisted laser desorption ionization mass spectrometry imaging (MALDI-MSI), was significantly improved by employing sample washing using a pH-controlled buffer solution. The pH of the washing solutions were set at values whereby the target analytes would have low solubility. Washing the tissue sections in the buffered solution resulted in removal of endogenous soluble ionization-suppressing compounds and salts, while the target compound remained in situ with minor or no delocalization during the buffered washing procedure. Two pharmaceutical compounds (cimetidine and imipramine) and one new protease inhibitor compound were successfully used to evaluate the feasibility of the pH-controlled tissue washing protocol for MALDI-MSI. Enhancement in signal-to-noise ratio was achieved by a factor of up to 10.     

Structural capacitor materials made from carbon fibre epoxy composites

In this paper, an approach towards realising novel multifunctional polymer composites is presented. A series of structural capacitor materials made from carbon fibre reinforced polymers have been developed, manufactured and tested. The structural capacitor materials were made from carbon fibre epoxy pre-preg woven laminae separated by a paper or polymer film dielectric separator. The structural capacitor multifunctional performance was characterised measuring capacitance, dielectric strength and interlaminar shear strength. The developed structural CFRP capacitor designs employing polymer film dielectrics (PA, PC and PET) offer remarkable multifunctional potential.     

Localized surface plasmon resonance spectroscopy of single silver nanocubes

In this work, we use dark-field microscopy to observe a new plasmon resonance effect for a single silver nanocube in which the plasmon line shape has two distinct peaks when the particles are located on a glass substrate. The dependence of the resonance on nanocube size and shape is characterized, and it is found that the bluer peak has a higher figure of merit for chemical sensing applications than that for other particle shapes that have been studied previously. Comparison of the measured results with finite difference time domain (FDTD) electrodynamics calculations enables us to confirm the accuracy of our spectral assignments.     

Measurements of the Thermal Effusivity of a Drop-Size Liquid Using the Pulse Transient Hot-Strip Technique

The thermal effusivity of drop-size liquids was measured by the pulse transient hot-strip technique. A strip sensor, used as a thermometer and heat source, is deposited on a smooth surface of an electrically insulating background material – onto which an insulating liquid sample is applied, completely covering the strip probe. Experiments can be made controlling the thermal penetration depth to within some 10 μm of the liquid sample – here demonstrated by measuring a drop of water at about 1% uncertainty. Measurements were made on water and a series of silicone oils (kinematic viscosity from 5 to 50 cSt; 1 cSt = 10⁻⁶ m²· s⁻¹) in microgravity conditions using a 10 m drop tower (10⁻³ g, 1.4 s), to investigate if any potential natural convection in the liquid at normal gravity condition is present, influencing the results. However, no such influence was observed. Paper presented at the Fifteenth Symposium on Thermophysical Properties, June 22–27, 2003, Boulder, Colorado, U.S.A.     

A method of predicting the image noise in paediatric multi-slice computed tomography images

The purpose of this study was to develop an equation with which to determine the tube current to be used in order to obtain a certain image noise level for differently sized children undergoing multi-slice computed tomography examination. The relationship between image noise and detector dose for different examination protocols was established for a LightSpeed Ultra, an eight slice CT from GEMS, using homogeneous water phantoms of different sizes. Three different anatomical areas (head, thorax and abdomen) were studied in 111 patients between 0 and 17 y of age. The mean ratio between the calculated and the measured noise in patient images was established for the different areas. Head examinations showed the best correlation (measured-to-calculated noise ratio = 1.01). In the thorax, the calculated noise was generally higher than the measured noise (ratio = 0.74), and in the abdomen, the opposite result was found (ratio = 1.20).     

Active and passive stabilization of body pitch in insect flight

Flying insects have evolved sophisticated sensory–motor systems, and here we argue that such systems are used to keep upright against intrinsic flight instabilities. We describe a theory that predicts the instability growth rate in body pitch from flapping-wing aerodynamics and reveals two ways of achieving balanced flight: active control with sufficiently rapid reactions and passive stabilization with high body drag. By glueing magnets to fruit flies and perturbing their flight using magnetic impulses, we show that these insects employ active control that is indeed fast relative to the instability. Moreover, we find that fruit flies with their control sensors disabled can keep upright if high-drag fibres are also attached to their bodies, an observation consistent with our prediction for the passive stability condition. Finally, we extend this framework to unify the control strategies used by hovering animals and also furnish criteria for achieving pitch stability in flapping-wing robots.     

The effect of accuracy motivation on anchoring and adjustment: Do people adjust from provided anchors?

Increasing accuracy motivation (e.g., by providing monetary incentives for accuracy) often fails to increase adjustment away from provided anchors, a result that has led researchers to conclude that people do not effortfully adjust away from such anchors. We challenge this conclusion. First, we show that people are typically uncertain about which way to adjust from provided anchors and that this uncertainty often causes people to believe that they have initially adjusted too far away from such anchors (Studies 1a and 1b). Then, we show that although accuracy motivation fails to increase the gap between anchors and final estimates when people are uncertain about the direction of adjustment, accuracy motivation does increase anchor–estimate gaps when people are certain about the direction of adjustment, and that this is true regardless of whether the anchors are provided or self-generated (Studies 2, 3a, 3b, and 5). These results suggest that people do effortfully adjust away from provided anchors but that uncertainty about the direction of adjustment makes that adjustment harder to detect than previously assumed. This conclusion has important theoretical implications, suggesting that currently emphasized distinctions between anchor types (self-generated vs. provided) are not fundamental and that ostensibly competing theories of anchoring (selective accessibility and anchoring-and-adjustment) are complementary. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel

Retained austenite transformation was studied for a 5 wt pct Cr cold work tool steel tempered at 798 K and 873 K (525 °C and 600 °C) followed by cooling to room temperature. Tempering cycles with variations in holding times were conducted to observe the mechanisms involved. Phase transformations were studied with dilatometry, and the resulting microstructures were characterized with X-ray diffraction and scanning electron microscopy. Tempering treatments at 798 K (525 °C) resulted in retained austenite transformation to martensite on cooling. The martensite start (M _s ) and martensite finish (M _f ) temperatures increased with longer holding times at tempering temperature. At the same time, the lattice parameter of retained austenite decreased. Calculations from the M _s temperatures and lattice parameters suggested that there was a decrease in carbon content of retained austenite as a result of precipitation of carbides prior to transformation. This was in agreement with the resulting microstructure and the contraction of the specimen during tempering, as observed by dilatometry. Tempering at 873 K (600 °C) resulted in precipitation of carbides in retained austenite followed by transformation to ferrite and carbides. This was further supported by the initial contraction and later expansion of the dilatometry specimen, the resulting microstructure, and the absence of any phase transformation on cooling from the tempering treatment. It was concluded that there are two mechanisms of retained austenite transformation occurring depending on tempering temperature and time. This was found useful in understanding the standard tempering treatment, and suggestions regarding alternative tempering treatments are discussed.     

Smoking tobacco, oral snuff, and alcohol in the etiology of squamous cell carcinoma of the head and neck: a population-based case-referent study in Sweden

BACKGROUND: This case-referent study was conducted to elucidate the role of selected exogenous agents in the etiology of head and neck cancer. The factors studied were tobacco smoking, alcohol intake, the use of moist oral snuff, dietary factors, occupational exposures, and oral hygiene. In this first report, the authors discuss the impact of tobacco smoking, the use of oral snuff, and alcohol consumption. METHODS: The study base was approximately 2 million person-years at risk and consisted of Swedish males age 40-79 years living in 2 geographic regions during the years 1988-1990. A total of 605 cases were identified in the base, and 756 controls were selected by stratified random sampling from population registries covering the base. RESULTS: Among those who were tobacco smokers at the time of the study, the relative risk of head and neck cancer was 6.5% (95% confidence interval, 4.4-9.5%). After cessation of smoking, the risk gradually declined, and no excess risk was found after 20 years. The relative risk associated with alcohol consumption of 50 grams or more per day versus less than 10 grams per day was 5.5% (95% confidence interval, 3.1-9.6%). An almost multiplicative effect was found for tobacco smoking and alcohol consumption. CONCLUSIONS: Tobacco smoking and alcohol intake had a strong interactive effect on the risk of squamous cell carcinoma of the head and neck. Moderate alcohol intake (10-19 grams per day) had little or no effect among nonsmokers. No increased risk was found for the use of Swedish oral snuff.