Modeling of hermetic transitions for microwave packages

Two numerical techniques, the finite difference in time domain (FDTD) and the finite element method (FEM) in frequency domain, are employed to characterize microstrip hermetic transition geometries in an effort to investigate high-frequency effects. Measurements performed on these transitions compare favorably with theory. Two different types of transitions have been analyzed from 10 to 25 GHz and have been found to be limited in performance by higher return loss as frequency increases. It is shown that microstrip-through-CPW hermetic transitions in the shielded environment may suffer from parasitic waveguide modes which, however, can be eliminated with the use of vias at appropriate locations. The hermetic wall on top of the CPW section shows a relatively small (≤ 2 dB) effect on the original circuit performance. Similarly, the hermetic bead transition shows good performance at a lower frequency region while it degrades as frequency increases. This indicates the need for very careful characterization of transitions intended for use in microwave and millimeter-wave applications. © 1996 John Wiley & Sons, Inc.     

Comparison of Canola and Soy Flour with Added Isocyanate as Wood Adhesives

Canola is widely grown in the northern latitudes for its vegetable oil, generating large quantities of residual, low value canola flour used as animal feed. The common wood adhesive poly(diphenylmethylene diisocyanate) (pMDI) should react with the wide variety of functional groups in proteins. Therefore, it would seem that canola flour with added pMDI could be an effective adhesive. Two main questions are addressed in this study: How do the wood adhesive properties of canola flour compare to the better-studied soy flour? How well do proteins, which contain an abundance of functional groups, cure with the very reactive pMDI? These questions were addressed using the small-scale adhesive strength test ASTM D-7998, with various adhesive formulations and bonding conditions for canola flour plus pMDI compared to soy adhesives. The more challenging wet cohesive bond strength was emphasized because the dry strengths were usually very good. Generally, soy adhesives were better than canola ones, as was the polyamidoamine-epichlorohydrin cross-linker compared to pMDI, but these generalizations can be altered by the conditions selected. Three-ply plywood tests supported the small-scale test results.     

Effects of Enantiomeric Blend of Verbenone on Response ofIps paraconfusus to Naturally Produced Aggregation Pheromone in the Laboratory

The aggregation pheromone produced by maleIps paraconfusus (Coleoptera: Scolytidae) tunneling in Monterey pine,Pinus radiata, logs was trapped on Porapak Q. A concentration of an extract of trapped volatiles that attracted beetles was determined in the laboratory through a concentration–response analysis of walking behavior of males and females. The interruptant effects of four concentrations of verbenone on response to a constant concentration of this naturally produced aggregation pheromone were tested with males and females. Independent of its enantiomeric composition [99.5% (S)-(–), 93.1 % (S)-(–), and 98.3% (R)-(+)], verbenone significantly reduced the percentage of females (but not males) reaching the attractant source. However, when the time required for beetles of both sexes taken together to reach the attractant source was considered, verbenone of higher enantiomeric purity had a greater effect on beetle behavior. Solutions of 99.5% (S)-(–)- and 98.3% (R)-(+)-verbenone increased the time required for beetles to reach the attractive source when compared to 93.1% (S)-(–)-verbenone. When pooled across enantiomeric blends, increasing concentrations of verbenone resulted in slower responses in beetles that reached the attractant source within 2 min. Males and females did not respond to verbenone alone.     

De novo fatty acid synthesis and fatty acid elongation catalyzed by subcellular fractions from hog and human aorta

De novo synthesis and mitochondrial elongation of fatty acids have been demonstrated in subcellular fractions from hog and human aorta. Microsomal fatty acid elongation has been shown in hog aorta. The activity catalyzing the formation of fatty acids from acetyl and malonyl CoA was associated with a high molecular weight complex in the 6×10⁶g×min supernatant fraction. The principal product was palmitic acid. Some myristic and stearic acids were also formed. One elongation system was associated with protein which sedimented between 4500 g×min and 150,000 g×min. It used acetyl CoA but not malonyl CoA, and NADH was the preferred reducing agent. Radioactivity from acetyl CoA was incorporated into many fatty acids. In hog aorta a second elongation system was found associated with protein which sedimented at 6×10⁶ g×min. It used malonyl CoA preferentially as substrate and either NADH or NADPH as reducing agent.     

Enhanced microbial oil production by activated sludge microorganisms via co‐fermentation of glucose and xylose

The co‐fermentation of glucose and xylose by activated sludge microorganisms for the production of microbial oils for use as biodiesel feedstock was investigated. Various carbon sources at initial concentration of 60 g/L and C:N ratio 70:1 were investigated: xylose, glucose, and 2:1 and 1:2 (by mass) glucose/xylose mixtures. Oil accumulation ranged between 12 to 22% CDW, the highest of which was obtained when xylose was the sole substrate used. Kinetic modeling of the fermentation data showed that specific growth and oil accumulation rates were similar in all substrate types and the lipid coefficient ranged from 0.02 to 0.06 g/g of sugar consumed. The fatty acid methyl ester yield and composition of the lipids showed their suitability for conversion to biodiesel. Based on the results, lignocellulose sugars could be used as fermentation substrates by activated sludge microorganisms for enhancing the oil content of sewage sludge for its use as a sustainable biofuel feedstock source. © 2013 American Institute of Chemical Engineers AIChE J, 59: 4036–4044, 2013     

Acceleration of kinetic monte carlo simulations of free radical copolymerization: A hybrid approach with scaling

Kinetic Monte Carlo (KMC) has been widely used in the simulation of polymeric reactions. The power of KMC is highlighted by its ability to keep track of the length and sequence of every radical or polymer chain, while it is computationally more expensive than deterministic kinetic models. This paper introduces an acceleration method that significantly reduces the computational cost of KMC simulations, while keeping the same features as the full kinetic Monte Carlo simulations. Case studies are used to demonstrate the general applicability of this method to free radical copolymerization. © 2017 American Institute of Chemical Engineers AIChE J, 63: 4013–4021, 2017     

Arsenic removal with iron(II) and iron(III) in waters with high silicate and phosphate concentrations

Arsenic removal by passive treatment, in which naturally present Fe(II) is oxidized by aeration and the forming iron(III) (hydr)oxides precipitate with adsorbed arsenic, is the simplest conceivable water treatment option. However, competing anions and low iron concentrations often require additional iron. Application of Fe(II) instead of the usually applied Fe(III) is shown to be advantageous, as oxidation of Fe(II) by dissolved oxygen causes partial oxidation of As(III) and iron(III) (hydr)oxides formed from Fe(II) have higher sorption capacities. In simulated groundwater (8.2 mM HCO3(-), 2.5 mM Ca2+, 1.6 mM Mg2+, 30 mg/L Si, 3 mg/L P, 500 ppb As(III), or As(V), pH 7.0 +/- 0.1), addition of Fe(II) clearly leads to better As removal than Fe(III). Multiple additions of Fe(II) further improved the removal of As(II). A competitive coprecipitation model that considers As(III) oxidation explains the observed results and allows the estimation of arsenic removal under different conditions. Lowering 500 microg/L As(III) to below 50 microg/L As(tot) in filtered water required > 80 mg/L Fe(III), 50-55 mg/L Fe(II) in one single addition, and 20-25 mg/L in multiple additions. With As(V), 10-12 mg/L Fe(II) and 15-18 mg/L Fe(III) was required. In the absence of Si and P, removal efficiencies for Fe(II) and Fe(III) were similar: 30-40 mg/L was required for As(II), and 2.0-2.5 mg/L was required for As(V). In a field study with 22 tubewells in Bangladesh, passive treatment efficiently removed phosphate, but iron contents were generally too low for efficient arsenic removal.     

Evaluation of curriculum to improve health professionals’ ability to manage age-related driving impairments

As our elderly population increases in proportion with respect to the rest of society, age-related driving impairments are increasing in importance as a public health concern. In this context, health professionals play an important role in identifying impaired drivers. This situation is complicated for two reasons: discussion of driving cessation is a sensitive topic for both health professionals and the elderly, and physicians have limited familiarity with the current American Medical Association (AMA) screening guidelines or mandated reporting laws.     

Morphologically dependent alternating‐current and direct‐current breakdown strength in silica–polypropylene nanocomposites

In this article, we report the synthesis of a new bimodal surface ligand morphology on silica nanoparticles. Combining grafting‐to and grafting‐from approaches, in this study, we demonstrated the efficacy of anthracene surface modification for improving the dielectric breakdown strength (DBS) under alternating‐current and direct‐current conditions and that of a matrix‐compatible polymer brush for controlling the nanofiller (NF) dispersion. Ligand‐modified spherical colloidal SiO₂ nanoparticles (～14 nm in diameter) were mixed into polypropylene, and the resulting dispersion was improved over the unmodified particles, as shown with transmission electron microscopy. The results suggest that the electronic structure of the anthracene‐modified particle surface was critical to the improvement in DBS. In addition, the DBS of the composite was shown to depend on the dispersion state of the filler and the mode of stress; this indicated that the individually dispersed nanoparticles were not necessarily the optimal morphology for all stress conditions. Additionally, the precise nature of the matrix‐compatible brush was less important than the NF dispersion it produced. The bimodal grafted architectural design has provided a promising solution for the control of the dispersion and surface properties, especially for high‐molecular‐weight polymer matrices. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44347.