碳纳米管(CNT)场发射显示器的关键技术的研究

对碳纳米管阴极的制备以及场发射显示器的真空封装技术进行了研究.利用一种新的碳纳米管生长工艺制备出了具有优良场发射性能的碳纳米管阴极.并将这种直接生长的碳纳米管薄膜作为阴极,结合一种弹性封装工艺,开发了一种具有简单字符显示功能的场发射显示器.该显示器在较低的工作电压下就可获得高亮度的显示效果,并且器件的亮度与驱动电压成较好的线性关系,这将有利于未来的碳纳米管场发射显示器实现高亮度和多级灰度显示.器件的持续工作寿命测试已经超过5500小时,充分验证了碳纳米管作为场发射阴极的应用潜力.     

Modulation and Equalisation Considerations for High Performance Radio LANs

The European Telecommunications Standards Institute (ETSI) has recently defined a European standard for a high performance radio LAN (known as HIPERLAN). To operate as wired LAN replacements, these systems will operate at 5.2 GHz and support instantaneous bit rates of just under 24 Mb/s. To counteract the time dispersive nature of the indoor radio channel, the use of adaptive equalisation is suggested. In this paper a number of possible modulation and equalisation techniques are presented and, in particular, the Bit Error Rate (BER) performance of quasi-coherent GMSK combined with Decision Feedback Equalisation is explored through computer simulation. The trade off between symbol spaced and fractionally spaced equalisation is considered together with the importance of feedfoward and feedback synchronisation to the channel's power delay profile. The paper also includes a comparison of the RLS and LMS based training algorithms and compares the modem developed under the ESPRIT III LAURA project with that specified in HIPERLAN.The application of dual antenna diversity is investigated and its impact on the number of received error free data packets obtained as a function of signal leval and rms delay spread. The use of such diversity is shown to greatly improve the BER performance of a HIPERLAN modem. The problem of frequency offset is considered and modifications are proposed to the HIPERLAN frame structure to improve the receiver's tolerance to such errors. Important practical issues such as frame and symbol synchronisation, frequency offset correction and hardware implementation are discussed from both the LAURA and HIPERLAN viewpoint.     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

参数化图形库技术

本文论述了参数化图形库的实现原理，建立了以尺寸叠加算法为基础的参数化图形库开发工具，利用这种开发工具建立的图形数据可以由数据库管理，方便有效。     

超声波车辆车轴探头的研制与应用

提出了一种用于检测在役车辆车轴产生疲劳裂纹的超声波方法,设计了中心孔探头与斜角探头一起,完成了对车辆车轴的关键区域探伤。     

940nm高功率激光二极管及线阵

设计并制作出了940 nm无铝有源区高功率激光二极管和激光条.通过MOCVD法生长出应变量子阱材料,器件显示出极好的性能,100μm条宽的激光二极管最大输出功率达800mW(室温),填充因子为17%的激光二极管条发射功率达32 W.     

微型无阀泵参数化结构设计及测试

 从理论计算和试验两方面研究了用于微流控化学分析芯片的微型无阀泵流动特性，初步建立了微型无阀泵流道结构的数学模型，重点讨论了结构参数的选取原则及相应的流动阻尼系数的计算方法． 通过试验验证了数值计算的可靠性，为微型无阀泵参数化设计及优化提供了理论依据及经验曲线．     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

Quantitative prediction of the degree of pollution of effluent from reactive dye mixtures

By using mathematical formulae developed in previous studies, certain pollution parameters of dye effluent obtained from reactive dyeing with a single dye can be predicted with good accuracy. In this study, the degree of pollution of reactive dyeing effluent using dye mixtures was also predicted by other approaches, such as linear and non-linear regression. The prediction accuracy was found to be satisfactory.     

超细水泥封堵技术

注水开发后期日益出现的地质问题及油套管的严重损坏,制约了油田的开发效果。针对河南油田注水开发中存在的上述问题,通过对超细水泥堵剂配方、堵剂性能、适应性等方面的研究,可实现对油井的高含水层、注水井的停注无用层、油水井套管外窜槽、穿孔、丝扣处的漏失等方面的封堵,取得了显著效果。自1998年8月-2001年12月在河南油田应用61井次,有效率85.3%,其中油井36井次,年度累计增油1.441×104t,降水7.6123×104m3;水井封堵25井次,累计增注14.32×104m3,控制无效注水16.95×104m3,创效益1800多万元,投入产出比达1:11.36,具有广泛的推广应用价值。