Measurement of the delayed-neutron yields in the fission of233U,236U,237Np,240Pu,and241Pu by neutrons from the spectrum of a fast reactor

Translated from Atomnaya Énergiya, Vol. 66, No. 2, pp. 100–103, February, 1989.     

A distribution function for double-bit upsets

It is suggested that the chord length distribution method could be useful for predicting double-bit upset rates in certain circumstances. A chord length distribution function for simultaneous path lengths in two parallelepipeds, applicable to a unidirectional flux, is derived. A proof of the system is outlined for the case under consideration     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

PCR-based procedures in detection and DNA-fingerprinting of Salmonella from samples of animal origin

The usefulness of selected PCR-protocols for the detection of Salmonella in 117 samples of animal origin (17 raw minced meat, 27 raw chicken meat, 8 raw sausages, and 25 egg samples, as well as 18 poultry faecal, and caecal swabs samples) and DNA-fingerprinting typing is shown. To establish an accurate PCR-procedure for Salmonella detection the following parameters were evaluated: two pre-PCR concentration procedures, centrifugation and immunomagnetic separation (IMS) using Dynabeads anti- Salmonella; the specificity and sensitivity of 10 sets of primers; and different conditions of the amplification reaction. In light of the results obtained from the use of PCR-based procedures alone or in combination with conventional methods, the following findings can be underlined: First, IMS is more efficient than centrifugation in the recovery of Salmonella. Second, the selected IMS/PCR-detection protocol is less time-consuming (45 h) than the IMS/culture procedure (90 h), and a good concordance between them was found when the Kappa coefficient was calculated (0·87). Third, PCR-ribotyping technique showed a very low discrimination power, being able to differentiate only three profiles. Fourth, RAPD technique using specific primers supports previous works in which it was proposed as a simple and useful tool for discriminating isolates between and within serotypes. Fifth, The efficiency, rapidity, and flexibility of the PCR-protocols applied were high, and they can be performed using two PCR-programs and the same basic equipment.     

Some Regularities of Heat and Mass Transfer in the Case of Fire Within a Building

Results of a numerical investigation of heat and mass transfer at the initial stage of fire within a building in combustion of kerosene, carried out with the use of a three-dimensional mathematical field model, are presented. A comparison of the distribution of the averaged temperatures and velocities along the vertical axis of the convective column and of the mass rates of gas flows through an open opening with the experimental data has been made. Substantial three-dimensional inhomogeneities of the velocities and the temperatures in the near-ceiling layer have been revealed. It has been established that near the opening there is a critical separation zone which influences significantly the parameters of natural gas transfer.     

High-voltage bridge for measuring spontaneous polarization,dielectric constants,and conductivity of ferroelectric crystals

Translated from Izmeritel'naya Tekhnika, No. 9, pp. 34–35, September, 1989.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.