Performance implications of the thermal-induced frequency drift infast wavelength switched systems with heterodyne detection

The frequency modulation response and tuning dynamics of a two-section DFB laser are determined by carrier and thermal modulation of the active layer refractive index. In response to a step change in the injection current for switching between channels in a wavelength division multiplexed system, the optical frequency changes rapidly due to the carrier effect, and then slowly drifts toward a steady state value due to the thermal effect. For wavelength switched applications with heterodyne detection, the drifting of the optical frequency broadens the spectrum of the IF signal and may impose a limit on the time that the signal remains within the IF passband (residency time). The IF spectral broadening and residency time are investigated theoretically and experimentally. Based upon a minimum mean square error fit between experimental and theoretical FM responses, the dependence of the spectral broadening and residency time on the bias condition of the laser and the optical frequency switching interval is characterized     

FAST MEASUREMENT OF ASH CONTENT IN COAL WASHING PLANT

The coal filter cake is a product of fine coal after floatation which has an ash content of 7-13%, water content of 30±2%, and a particle size of less than 1 mm. The ash content was measured by the intensity of the single backscattered gamma-ray, and its accuracy is mainly dependent on the energy of the gamma-ray. The 238Pu low energy photon source is selected in this work. The energy of its gamma-ray is 15 keV, which can result not only in the best sensitivity, but also in the lowest contribution to the environment radiation. The root mean square deviation of the ash measurement is±0.33% (±1σ).     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

环境放射化学研究中几个问题的讨论

本文从辐射环境保护和公众辐射防护的角度，讨论了放射性核素在环境中的迁移行为，放射性核素与环境介质的相互作用和放射性核素在环境中的形态等涉及到环境放射化学研究方向的问题，并讨论了它们之间相互依存的关系。     

Group decision support system for assessment of problem-basedlearning

Assessment is an important task in problem-based learning (PBL). It has a strong influence on students' approaches to learning and their outcomes. In order to provide an open and fair method of PBL assessment, a group decision support system (GDSS) has been developed. The system uses mathematical decision methods for collecting assessment criteria and their appropriate weights, and databases for storing students' details and data on the assessment criteria. It integrates databases with model bases in a cooperative decision-making environment and is implemented on a client-server platform using a relational database management system. The GDSS has been developed and used to improve the efficiency and quality of assessing students' PBL outcomes     

金刚石光电导探测器研制及在软X光测量中的初步应用

介绍了我们自己设计制造的天然Ⅱａ型金刚石光导探测器的结构，原理，制造工艺，实验标定及其在ＩＣＦ实验中软Ｘ光测量中的应用等。     

A Survey on the Numerics and Computations for the Landau-Lifshitz Equation of Micromagnetism

The Landau-Lifshitz (LL)equation of micromagnetism governs rich variety of the evolution of magnetization patterns in ferromagnetic media. This is due to the complexity of physical quantities appearing in the LL equation. This complexity causes also an interesting mathematical properties of the LL equation: nonlocal character for some quantities,nonconvex side-constraints, strongly nonlinear terms. These effects influence also the numerical approximations. In this work, recent developments on the approximation of weak solutions, together with the overview of well-known methods for strong solutions,are addressed. Author is supported by the Fund for Scientific Research - Flanders FWO (Belgium).     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位