Morphology and characterization of conductive films based on polyaniline‐coated polystyrene latexes

The polyaniline (PANI)‐coated polystyrene (PS) latexes were synthesized, and the electrically conductive films were prepared thereafter. The weight ratio of PANI was 5%. Thermal analysis of the latices was performed using DSC and TGA. In this study, the electrically conductive films were prepared above the PS glass transition temperature (T_g). During the film formation, the effects of the annealing temperature and atmosphere (air or N₂) on the film resistance were investigated. In addition, the film morphology was observed utilizing scanning electron microscopy. The film resistance decreased in the initial heating stage due to the increasing temperature and the compaction of film. Then the film resistance increased with further annealing due to the aging of PANI. Typically, the film resistance was about 6000 Ω/sq, and the conductivity was 0.3 S/cm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5406–5413, 2006     

Dynamic mechanical,rheological, and morphological studies of polyacrylate-graft-poly (vinyl chloride) suspension resin

A series of polyacrylate-graft-poly (vinyl chloride) (ACR-g-PVC) resins were prepared through suspension graft copolymerization. Three kinds of polyacrylate latices were grafted by vinyl chloride using suspension polymerization method at 57 ± 0.1°C, respectively. The dynamic mechanical and rheological properties and the morphology of the resulting ACR-g-PVC resins were investigated. Poly (butyl acrylate)-graft-poly (vinyl chloride) (PBA-g-PVC) resin exhibited better toughness, and the optimized content of PBA in ACR-g-PVC resin was 6–8 wt%. The melt viscosity of ACR-g-PVC resin was much lower than that of pure PVC. The nature of the fracture surfaces of ACR-g-PVC material indicated that it has good toughness. The impact strength of the PBA-g-PVC material was greatly improved compared with that of pure PVC. The Young's modulus of the ACR-g-PVC material containing less than 15 wt% of PBA was comparable to that of pure PVC according to their dynamic mechanical analysis curves. For all of the ACR-g-PVC resins, there were two individual relaxations in the low-temperature range. One was β transition of PVC, and the other was α transition of ACR. The glass transition temperature of PVC in the ACR-g-PVC resin shifted to lower temperature when the content of the PBA was above 50 wt%. POLYM. ENG. SCI., 47:996–1003, 2007. © 2007 Society of Plastics Engineers     

Aromatization of n-butane over new LD-HBS catalysts. Effect of the gallium oxide support

It is shown that even pure quartz, other silicas or aluminas can enhance the aromatization activity of a ZSM-5 zeolite. Incorporation of gallium oxide onto these supports increases further the production of aromatics. The use of supported gallium oxide co-catalyst obtained by co-evaporation of a colloidal silica and a Ga salt has led to extremely high aromatization performance for the hybrid catalyst.     

Studies on crystal morphology and crystallization kinetics of polypropylene filled with CaCO3 of different size and size distribution

Changes in the crystal morphology, crystallinity, and the melting temperature of thermoplastics resulted in significant changes in the mechanical behavior of composites containing them. For this reason, the research of crystal morphology and crystallization kinetics in thermoplastic composites became an important requirement. The thermoplastic filled with the filler of different size gradation was a new method for improving processability of thermoplastic composites. We have previously reported that the melt viscosity of polypropylene (PP) composites, which were filled with 30 wt % CaCO₃ of effective size gradation, could be evidently declined. In this study, two sizes of CaCO₃, 325 meshes and 1500 meshes, were blended by different proportions and filled into PP matrix with 30 wt %. Crystal morphology and isothermal crystallization kinetics of a series of composites were characterized by differential scanning calorimeter (DSC) and polarizing microscope. The results showed that composites filled with CaCO₃ of effective size gradation leaded to a well‐crystalline order and a large crystal size, while their isothermal crystallization kinetics and crystallization rate constant (k) were declined, and their Avrami exponents (n) and crystallization half‐life (t_1/2) were increased compared with the composites filled with single size CaCO₃. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2437–2444, 2006     

聚合物流变性能对共注射成型的影响

在共注射成型多相分层流动充模成型机理的基础上，揭示了芯壳层熔体对共注射成型的分层界面形貌和芯层熔体前沿突破的影响，并模拟了芯壳层熔体粘度比对共注射成型的影响，建立了芯壳层熔体粘度与分层界面和前沿移动界面菜貌的关系。本文的模拟研究结果与一些文献的实验结果相吻合。     

Nonisothermal crystallization kinetics of poly(butylene terephthalate)/montmorillonite nanocomposites

The melt intercalation method was employed to prepare poly(butylene terephthalate) (PBT)/montmorillonite (MMT) nanocomposites, and the microstructures were characterized with X‐ray diffraction and transmission electron microscopy. Then, the nonisothermal crystallization behavior of the nanocomposites was studied with differential scanning calorimetry (DSC). The DSC results showed that the exothermic peaks for the nanocomposites distinctly shifted to lower temperatures at various cooling rates in comparison with that for pure PBT, and with increasing MMT content, the peak crystallization temperature of the PBT/MMT hybrids declined gradually. The nonisothermal crystallization kinetics were analyzed by the Avrami, Jeziorny, Ozawa, and Mo methods on the basis of the DSC data. The results revealed that very small amounts of clay (1 wt %) could accelerate the crystallization process, whereas higher clay loadings reduced the rate of crystallization. In addition, the activation energy for the transport of the macromolecular segments to the growing surface was determined by the Kissinger method. The results clearly indicated that the hybrids with small amounts of clay presented lower activation energy than PBT, whereas those with higher clay loadings showed higher activation energy. The MMT content and the crystallization conditions as well as the nature of the matrix itself affected the crystallization behavior of the hybrids. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3257–3265, 2006     

Preparation of narrowly distributed nanoparticles of poly(n‐butyl methacrylate‐co‐vinyl pyrrolidone) through microemulsion polymerization

Narrowly distributed nanoparticles of poly (n‐butyl methacrylate‐co‐vinyl pyrrolidone) were prepared through microemulsion polymerization with a nonionic surfactant of Tween‐80 as emulsifier (6 wt % of the latex) and n‐butanol as coemulsifier. The polymerizations were initiated with benzoylperoxide (BPO), potassium persulfate (KPS), KPS/ferric sulfate (FeSO₄), and BPO/FeSO₄, respectively, where the initiation in the case of BPO/FeSO₄ took place mainly at the interphase between the oil phase and the reaction media. Namely, this interfacial‐initiated microemulsion polymerization resulted in larger particles with relatively narrower particle size distribution as well as higher limiting monomer conversion but lower polymerization rate compared with the polymerization initiated with KPS/FeSO₄. In this article, the influences of initiation method, monomer ratio, and addition of water‐soluble components on microemulsion polymerization and latex particle size were studied to discuss the mechanism of interfacial‐initiated microemulsion polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2334–2340, 2004     

Effect of high polymerization temperature on the microstructure of isotactic polypropylene prepared using heterogeneous ticl4/mgcl2 catalysts

The effects of alkylaluminum and polymerization temperature on propylene polymerization without an external donor in the use of a TiCl₄–MgCl₂–diether(BMMF) catalyst were investigated. The results indicated that with increasing polymerization temperature the concentrations of [mmmm] of heptane‐insoluble poly(propylene) (PP) fraction increased. Crystallization analysis fractionation (CRYSTAF) results showed the fractions of different crystallization temperatures were changed according to various polymerization temperatures. The activity with Et₃Al as cocatalyst at 100°C was much lower than that at 70°C. However, the activity with i‐Bu₃Al at 100°C was as high as that at 70°C. The fraction of high‐crystallization temperature of PPs obtained with i‐Bu₃Al increased with increasing polymerization temperature, which was opposite to that with Et₃Al, thus implying that the copolymerization of propylene with the monomer arising from Et₃Al led to the lower crystallization ability of PPs obtained with Et₃Al. The terminal groups of PP suggested that the chain‐transfer reaction by β‐H abstraction was the main chain‐transfer reaction at 120°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3980–3986, 2003     

Preparation and properties of T300 carbon fiber‐reinforced thermoplastic polyimide composites

In this study, a series of T300 carbon fiber‐reinforced polyimide (CFRPI) composites were prepared by laminating premolding polyimide (PI) films with unidirectional carbon fiber (CF) layers. On the basis of PI systems design, the effect of CF volume fraction, processing conditions, and PI molecular structure on the properties of CFRPI composites was studied in detail. In addition, two kinds of nano‐particles, including carbon nano‐tube (CNT) and SiO₂ were filled into the premolding PI films with different concentrations. And the effect of nano‐particles on the properties of CFRPI composites was also investigated. The surface characteristic of T300 CF was measured by X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The properties of premolding PI film and CFRPI composites were measured by dynamic mechanical analysis (DMTA), SANS testing machine, scanning electron microscopy (SEM), and so forth. These experimental results showed that the properties of CFRPI composites were mainly affected by the premolding PI film and molding condition. The change of CF volume fraction from 55% to 65% took little effect on the mechanical properties of CFRPI composites. In addition, the incorporation of nano‐particle SiO₂ could further improve the properties of CFRPI composites, but CNT hardly improved the properties of CFRPI composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 646–654, 2006     

美国《1990年建筑作品版权保护法》评述

在1990年12月以前,建筑作品是作为绘画、图形和雕塑作品获得版权保护的.但是建筑本身被认为是一种实用物品,因而不受版权的保护.然而在1989年3月1日,美国加入《伯尔尼公约》.为了履行公约义务,美国国会通过了《1990年建筑作品版权保护法》(简称AWCPA),对《1976年版权法》进行了相应的修正,建筑作品作为独立的一类作品受版权法的保护,拓宽了建筑作品的保护范围,对建筑作品侵权的认定标准也发生变化.