Microwave-assisted desulfurization of NOx storage-reduction catalyst

The activity of NO_x storage-reduction (NSR) catalysts is greatly reduced by sulfur poisoning, caused by the SO₂ present in the exhaust stream. Desorption of sulfur species from poisoned NSR catalysts occurs at temperatures in excess of 600 °C using reducing atmospheres and conventional heating. In this work, microwave (MW) heating has been used to promote desulfurization of poisoned NSR catalysts. The experiments were carried out by heating the catalyst with MW radiation and using hydrogen as the reducing gas. Desorption of H₂S at 200 °C was observed. Desorption at even lower temperatures (150 °C) was observed when water was introduced to the system. In the presence of water, sulfur species desorbed as both H₂S and SO₂. An overall reduction of sulfur species of about 60% was obtained. The use of MW heating proves to be an efficient way to achieve regeneration of poisoned NSR catalysts.     

Drying characteristics of porous material immersed in a bed of hygroscopic porous particles fluidized under reduced pressure

A relatively large wet material was immersed in a fluidized bed of hygroscopic porous particle (silica gel beads) under reduced pressure. And then the drying characteristics were compared with those in the case of inert particle (glass beads). The comparison of drying characteristics is performed experimentally and theoretically. In calculation, the water transfer from the sample to the fluidized bed was considered. The calculation results are in good agreement with the experimental data. The effects of the operational conditions (the pressure in the drying chamber and the temperature of the drying gas) on the drying characteristics were also examined in both fluidizing particles.The drying finishes earlier in the case of hygroscopic porous particle than in the case of inert particle regardless of pressure in the drying chamber, since the water transfer from the sample facilitates the drying in the case of hygroscopic porous particles. The temperature decrement in drying appears in the case of inert particle. This phenomenon is also observed in the case of hygroscopic porous particle, but the decrement degree of the temperature is much smaller than that in the case of inert particle. The difference of the minimum temperature in the sample in drying between the cases of hygroscopic porous particle and inert particle is very slight for different pressures in the drying chamber.     

COLOURING OF PURE IRON AFTER Ti~＋-O~＋ DUAL ION IMPLANTATION

用电化学的方法对经Ｔｉ~＋－Ｏ~＋二重离子注入后的钝铁表面进行处理，可呈现出深蓝、海蓝、褐、紫、金黄、淡黄等颜色用Ｘ射线光电子能谱（ＸＰＳ）对着色表面进行分析，发现表层有ＴｉＯ＿２富集，证明存在钛的氧化物是着色的必要条件．同时着色后的表面存在Ｔｉ的浓化层，着色的深浅程度与钛的浓度有关     

On-chip Diamond MEMS Magnetic Sensing through Multifunctionalized Magnetostrictive Thin Film

Electrically integrable, high-sensitivity, and high-reliability magnetic sensors are not yet realized at high temperatures (500 °C). In this study, an integrated on-chip single-crystal diamond (SCD) micro-electromechanical system (MEMS) magnetic transducer is demonstrated by coupling SCD with a large magnetostrictive FeGa film. The FeGa film is multifunctionalized to actuate the resonator, self-sense the external magnetic field, and electrically readout the resonance signal. The on-chip SCD MEMS transducer shows a high sensitivity of 3.2 Hz mT⁻¹ from room temperature to 500 °C and a low noise level of 9.45 nT Hz^−1/2 up to 300 °C. The minimum fluctuation of the resonance frequency is 1.9 × 10⁻⁶ at room temperature and 2.3 × 10⁻⁶ at 300 °C. An SCD MEMS resonator array with parallel electric readout is subsequently achieved, thus providing a basis for the development of magnetic image sensors. The present study facilitates the development of highly integrated on-chip MEMS resonator transducers with high performance and high thermal stability.     

Fabrication of piezoelectric multilayer thin-film actuators

In this study, we fabricated multilayer ceramics (MLCs) composed of multilayered Pb(Zr,Ti)O₃ (PZT) piezoelectric thin films with internal electrodes and evaluated their dielectric and piezoelectric properties. The stack of PZT ferroelectric layers (550 nm) and SrRuO₃ (SRO, 80 nm) electrodes were alternatively deposited on Pt/Ti-coated silicon-on-insulator substrates by radio-frequency magnetron sputtering. The MLCs composed of one, three, and five PZT layers were fabricated by the alternate sputtering deposition of PZT ferroelectric layers and SRO electrodes through the movable shadow mask. The capacitances of MLCs were proportionally increased with the number of PZT layers, while their relative dielectric constants were almost same among the each MLC. The MLCs exhibited symmetric and saturated P–E hysteresis loops similar to the conventional PZT thin films. We estimated that the piezoelectric properties of MLCs by FEM simulation, and confirmed that the effective transverse piezoelectric coefficients (d _31,eff ) increased with the number of PZT layers. The piezoelectric coefficients calculated to be d _31,eff  = ?2964 pC/N at 25 PZT layers, which is much higher than those of conventional single-layer piezoelectric thin films.     

Development of a liquid tin microjet target for an efficient laser-produced plasma extreme ultraviolet source

A regenerative tin liquid microjet target was developed for a high average power extreme ultraviolet (EUV) source. The diameter of the target was smaller than 160 microm and good vacuum lower than 0.5 Pa was maintained during the operation. A maximum EUV conversion efficiency of 1.8% at the Nd:yttrium-aluminum-garnet laser intensity of around 2 x 10(11) Wcm(2) with a spot diameter of 175 microm (full width at half maximum) was observed. The angular distribution of the EUV emission remained almost isotropic, whereas suprathermal ions mainly emerged toward the target normal.     

Doped Helium Crystals Growth and Study

No Heading The new technique for embedding microimpurities into solid helium has been developed. A He crystal was grown in a vertical cylindrical cell placed in the bath of pumped LHe cryostat. The He solid was continuously moved downward by exhaust of helium from the cell bottom and was simultaneously restored from its upper edge by sedimentation of a jet of gas helium mixed with impurity. A guest particle density of 3· 10¹⁹ per cc and stable during an hour doped crystal growth with the rate of 1 mm per 20 s were achieved. The solid Deuterium clusters isolated in solid Helium have been investigated at T = 1.3K and P = 3 MPa by CARS technique. The strong effect of Raman scattering sensitivity to the molecular environment nuclear spin has been found in CARS - the ratio of probabilities for the scattering by para (J=1) and ortho (J=0) deuterium being equal to 1 in a gas is as high as 10,000 in nearly pure o-D₂, whereas it is 50 in common Raman scattering. This effect has been shown to give rise starting from cluster size corresponding to the phonon band onset.PACS numbers: 33.20 Fb; 33.70 Jg: 67.80 Mg     

Very low threshold current density of 1.3-/spl mu/m-range GaInNAsSb-GaNAs3 and 5 QWs lasers

The dependence of the threshold current density on the number of wells for 1.3-/spl mu/m-range edge emitting lasers using GaInNAsSb novel material, at which the incorporation of the small amount of Sb make the two-dimensional growth condition wide, is studied. The lowest record ever reported for the threshold current density per well (Jth A/cm/sup 2//well@L=900 /spl mu/m) for 3 QWs lasers was achieved. GaInNAs-based 5 QWs lasers with the very low threshold current density per well of 160 A/cm/sup 2/ were successfully grown for the first time. Therefore, no significant deterioration of Jth is observed even though the number of wells increased up to 5. Since Jth of 5 QWs doesn't increased rapidly compared to SQW and 3 QWs as decreasing the cavity length, it is considered that lower Jth can be obtained by utilizing 5 QWs in devices such VCSELs which use short cavity length.     

13 years’ operational experience of SPring-8 vacuum system

The first electron beam was stored in SPring-8 storage ring in March 1997. An overview of the 13 years’ operational experience concerning the vacuum system of the SPring-8 storage ring is presented. The evolution of the vacuum system and their performance are summarized. Moreover, the main vacuum failures and their impact on accelerator operation are described in detail. We analyze the relationship between the difference types of vacuum failure and downtime of user experiment.     

Modeling of quantitative relationships between physicochemical properties of active pharmaceutical ingredients and tensile strength of tablets using a boosted tree

Objectives: The aim of this study was to explore the potential of boosted tree (BT) to develop a correlation model between active pharmaceutical ingredient (API) characteristics and a tensile strength (TS) of tablets as critical quality attributes.

Methods: First, we evaluated 81 kinds of API characteristics, such as particle size distribution, bulk density, tapped density, Hausner ratio, moisture content, elastic recovery, molecular weight, and partition coefficient. Next, we prepared tablets containing 50% API, 49% microcrystalline cellulose, and 1% magnesium stearate using direct compression at 6, 8, and 10?kN, and measured TS. Then, we applied BT to our dataset to develop a correlation model. Finally, the constructed BT model was validated using k-fold cross-validation.

Results: Results showed that the BT model achieved high-performance statistics, whereas multiple regression analysis resulted in poor estimations. Sensitivity analysis of the BT model revealed that diameter of powder particles at the 10th percentile of the cumulative percentage size distribution was the most crucial factor for TS. In addition, the influences of moisture content, partition coefficients, and modal diameter were appreciably meaningful factors.

Conclusions: This study demonstrates that BT model could provide comprehensive understanding of the latent structure underlying APIs and TS of tablets.