The effect of aging on muscle activation and postural control pattern for young and older computer users

A lot of older adults try to learn to use computers and might use different ways to perform a computer task compared to younger people. Fifteen healthy young and 15 healthy older adults participated in this study and all performed a series of mouse tasks. A three dimensional motion capture system and electromyographic analysis were used to obtain kinematic and kinetic data during performing the computer tasks. Three-way analysis of variance with repeated measures on task and time factors was used to analyze all dependent measurements. Older adults had higher RMS of forearm muscles compared to the young adults. The RMS of the finger extensor was highest when performing a dragging task. Compared with young adults, the older adults had greater cranial-cervical angle and neck flexion, but smaller head flexion, shoulder angle, elbow angle and ulnar deviation. Consequently, the older adults might have a greater risk of developing musculoskeletal disorder.     

Photoluminescent characterization of KNbO3:Eu

In this study, the photoluminescence (PL) spectra of europium-doped potassium niobate (KNbO₃) crystallites prepared by a vibrating milled solid-state reaction method were studied. X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical spectral analysis (luminescence excitation, emission spectra and time-resolved spectra) were used to characterize the KNbO₃:Eu³⁺ powders. The results of the XRD revealed that the powders remained as a single orthorhombic structure at doping concentrations below 3 mol%. A second phase of EuNbO₄ begins to appear at 5 mol%. The ⁵D₀–⁷F₁ (593 nm) and ⁵D₀–⁷F₂ (614 nm) emission characteristics of Eu³⁺ appear at a quenching concentration of above 3 mol%. The Commission Internationale d’Eclairage (CIE) chromaticity coordinates of a Eu:KNbO₃ host excited at λ_ex = 400 nm and λ_ex = 466 nm wavelengths, both presented a red-shift when increasing the Eu³⁺ ion doping. The lifetime of the Eu³⁺ ion decreased as the doping concentration was increased from 1 to 7 mol%.     

Terrain correction computation using Gaussian quadrature

A method and a program (tcq) in FORTRAN 90 based on Gaussian quadrature are developed to compute the terrain correction (TC). TCs were determined on 1010 benchmarks using the Gaussian quadrature, prism and FFT methods using a 3″×3″ elevation grid for the inner zone and a 30″×30″ elevation grid for the outer zone. In order to achieve a 0.1 mgal accuracy in TC while reducing the computing time, the best inner and outer radii for TC computation are 20 and 200 km, respectively. The Gaussian quadrature is a highly accurate numerical integrator and yields results that outperform those from the prism method and the FFT method. The singular problem of the kernel function in TC is treated by considering the innermost zone effect, which can be expressed as a complete elliptic integral of the first kind. The innermost zone effect must be taken into account if the required accuracy of TC is at a 1-mgal level.     

Comparison of a‐Si and Poly‐Si for AMOLED displays

Abstract— The characteristics of OLED backplanes including the intrinsic properties of a‐Si TFTs and LTPS TFTs will be reviewed. While LTPS TFTs reveal satisfactory stability in AMOLED‐display applications, a‐Si AMOLEDs show better uniformity and are capable of driving OLEDs. However, the stability of a‐Si TFTs under long‐term operation is still unacceptable and remains to be the key issue constraining the commercialization of a‐Si TFT AMOLEDs.     

Creation of arbitrary spectra with an acousto-optic modulator and an injection-locked diode laser

We use a double-passed acousto-optic modulator (AOM), driven by an arbitrary waveform generator to produce multiple frequency components for a laser with arbitrary frequency spacings. A programmed sequence containing various sections of radio-frequency sinusoidal signal at different frequency is applied to drive the AOM. The diffracted light is used to injection-lock a diode laser. The combined techniques allow us to generate the multi-line spectra for the diode laser with arbitrary frequency spacings in the range of 100 MHz at a relatively high output power of 80 mW and a small power variation of 2%. Such a light source can be used in the application for laser cooling of molecules.     

Transparent polyimide/graphene oxide nanocomposite with improved moisture barrier property

Colorless and organo-soluble polyimide (PI) films have been synthesized from an alicyclic dianhydride BCDA and aromatic diamine 3,4′-ODA in the cosolvent of DMAc and GBL via one-step process. The graphene oxide (GO) was mixed with the above PI in DMAc solution to fabricate the PI/GO nanocomposite films. With the addition of only 0.001 wt% of GO in PI matrix, the resultant nanocomposite (PI/GO-0.001) exhibits not only the enhanced resistance to moisture but also retains superior visible light transmission, enhanced mechanical strength, and excellent dimensional stability, simultaneously. The water-vapor-transmission-rate (WVTR) significantly reduced to 30 g mil m⁻² day⁻¹ for this nanocomposite compared to 181 g mil m⁻² day⁻¹ for pure PI. Notably, the PI/GO-0.001 nanocomposite also exhibits low coefficient of thermal expansion (CTE) of 41 ppm °C⁻¹, which is benefited from the homogeneous distribution of ultrathin GO nanosheets in PI matrix.     

Adaptive joint beamforming and B‐MMSE detection for CDMA signal reception under multipath interference

The combination of antenna array beamforming with multiuser detection can effectively improve the detection efficiency of a wireless system under multipath interference, especially in a fast‐fading channel. This paper studies the performance of an adaptive beamformer incorporated with a block‐wise minimum mean square error(B‐MMSE) detector, which works on a unique signal frame characterized by training sequence preamble and data blocks segmented by zero‐bits. Both beam‐former weights updating and B‐MMSE detection are carried out by either least mean square (LMS) or recursive least square (RLS) algorithm. The comparison of the two adaptive algorithms applied to both beamformer and B‐MMSE detector will be made in terms of convergence behaviour and estimation mean square error. Various multipath patterns are considered to test the receiver's responding rapidity to changing multipath interference. The performance of the adaptive B‐MMSE detector is also compared with that of non‐adaptive version (i.e. through direct matrix inversion). The final performance in error probability simulation reveals that the RLS/B‐MMSE scheme outperforms non‐adaptive B‐MMSE by 1–5 dB, depending on the multipath channel delay profiles of concern. The obtained results also suggest that adaptive beamformer should use RLS algorithm for its fast and robust convergence property; while the B‐MMSE filter can choose either LMS or RLS algorithm depending on antenna array size, multipath severity and implementation complexity. Copyright © 2004 John Wiley & Sons, Ltd.     

A miniature generator using piezoelectric bender with elastic base

Nowadays green energy devices such as vibration generators attempt to harvest energy from environment. A lot of studies dealing with vibration generators put emphasis on mechanism designs or power generation methods, but few on lowering the resonant frequency of power generation systems. This study proposes that elastic bases attached to vibration generators can lower natural frequencies, so as to make natural frequencies closer to ambient vibration frequency. Therefore, this study investigates miniature electric generators consisting of piezoelectric benders and elastic bases. To install the elastic base, this work uses a spring with prescribed stiffness and a board with given mass between the piezoelectric bender and a vibration source to make the resonant frequency of piezoelectric benders close to the frequency of ambient vibration. Analytical derivation is carried out to obtain optimal mass and stiffness. Accordingly, more electric power can be generated from piezoelectric generators using an elastic base with appropriate mass and stiffness. According to experimental results, using an elastic base increases 376 times generated power compared with no elastic base. In the presence of the elastic base, the power increases 132% when a point mass is added.