Improvements in CVD/CVI processes for optimizing nanocrystalline diamond growth into porous silicon

This paper reports a novel procedure to infiltrate nanocrystalline diamond films (NCD) on porous silicon (PS) substrate. The NCD/PS films resulted in a composite material, with great potential for electrochemical application, mainly due to its high active surface area. The Hot Filament Chemical Vapor Deposition reactor was changed to Hot Filament Chemical Vapor Infiltration reactor in order to grow NCD films infiltrated into deep holes of PS substrate. This procedure allowed the infiltration of the reacting gases into the porous structure where the nucleation takes place, followed by the coalescence and film formation at pore bottoms and walls. In this configuration an additional entrance of CH₄ was located next to the PS substrate using two distinct positions called “underneath” and “above”, with the use of the additional flow accurately underneath or above of the samples. In general, the combination of these two configurations with additional carbon sources provided NCD film infiltration in PS substrate with success with only 60 min of growing time. Particularly, the films obtained from the positions called “above” presented the best morphology, with high quality and crystallinity, confirmed from its scanning electron microscopy, Raman scattering spectroscopy and high resolution X-ray diffraction spectra, respectively.     

Thermal Fatigue Behavior of Thick and Porous Thermal Barrier Coatings Systems

High-temperature thermal fatigue causes the failure of thermal barrier coating (TBC) systems. This paper addresses the development of thick TBCs, focusing on the microstructure and the porosity of the yttria partially stabilized zirconia (YPSZ) coating, regarding its resistance to thermal fatigue. Thick TBCs, with different porosity levels, were produced by means of a CoNiCrAlY bond coat and YPSZ top coat, both had been sprayed by air plasma spray. The thermal fatigue resistance of new TBC systems and the evolution of the coatings before and after thermal cycling was then evaluated. The limit of thermal fatigue resistance increases depending on the amount of porosity in the top coat. Raman analysis shows that the compressive in-plane stress increases in the TBC systems after thermal cycling, nevertheless the increasing rate has a trend which is contrary to the porosity level of top coat. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Hydrogen-helium scattering cross-sections for transmission elastic recoil detection analysis

¹H(,p) ⁴He scattering cross-sections were determined for the 6.5–13 MeV (incident energy) range, thereby extending the energy range for such data beyond that available in the literature. These values are essential for the further development of hydrogen concentration profiling by the transmission elastic recoil detection technique, of particular interest in the design of surface-engineered hydrogen contamination barriers for steels.     

Effective section method: A general direct method for the design of steel cold-formed members under local–global buckling interaction

Thin-walled steel cold-formed members usually display local–global buckling interaction which strongly affects the structural strength of columns and beams. The local bucking of slender folded sections develops in analogy with single plate buckling, including the interaction between the plate elements of the cross-section and can be identified with appropriate first-order stability analysis and the consequent results of the critical buckling loads and the associated modes. The effective section method, ESM, as an extension of the original effective area method, EAM, was conceived for the design of cold-formed members on the basis of the actual local buckling results of the section, together with calibrated formulations for column and beam resistance. The strength equations were taken from the direct strength method, DSM, as it is presented in the North American AISI standard. In addition, as a consequence of its proposed formulation the effective section method is able to be applied side-by-side with the traditional effective width method, EWM, allowing its inclusion in the main part of the codes and specifications for the design of cold-formed members and improving its dissemination. The ESM was proposed in combination with equations and tables that enables designers to directly access the critical local buckling compressive force and bending moment of usual sections, resulting in a contribution that improves the attractiveness of the method.     

Effect of a commercial dispersion of multi walled carbon nanotubes on the hydration of an oil well cementing paste

This work studies the influence of a commercial dispersion of multi wall carbon nanotubes (MWCNT) on the hydration of a class G cement paste, at room and elevated down-hole temperatures. The MWCNT dispersion was produced with a solids concentration of 3.0 % by mass and an anionic surfactant as dispersing agent. Cement pastes with water-to-cement ratio of 0.45 and additions of solid MWCNT by mass of cement up to 0.50 % were studied. Isothermal calorimetry results showed a clear retardation of the hydration of cement caused by the surfactant contained in the MWCNT dispersion. Nevertheless, thermogravimetric evaluations showed that once the hydration reaction resumed, the retardation effect of the surfactant did not have a negative impact on the amount of hydration products precipitated. It was concluded that the commercial MWCNT dispersion presents a good potential to be applied in oil well cement pastes.     

Evaluation of equivalent linear methods for estimating target displacements of existing structures

This paper presents a statistical study that evaluates the accuracy of four equivalent linear methods which allow the maximum deformation demands of nonlinear structures to be estimated from the maximum deformation demands of the equivalent linear ones. Three of them are defined by displacement ductility ratios, and the other is defined by lateral strength ratios. It is shown from the study that conclusions for the approximate displacements derived from structures with known displacement ductility ratios (new structures) such as the work done by Miranda and Ruiz-Garcia in 2002 [16] are not applicable to structures with known strength ratios (existing structures). The equivalent damping of the equivalent linear systems is usually greater than 5% and the design response spectra specified in codes have a viscous damping ratio of 5% only. Therefore, the highly damped maximum displacement responses of the equivalent linear systems in this study are derived from both damping reduction factors and linear response-history analyses to discuss the effect of different damping reduction factors. Elastoplastic single-degree-of-freedom systems with periods between 0.1 and 3.0 s are considered when subjected to 72 earthquake ground motions recorded on firm sites in California. Mean ratios and the dispersion of approximate to exact maximum inelastic displacements for each method are computed as functions of periods of vibration and strength ratios. This study focuses on existing structures, which already have known vibrating periods and strength ratios.     

Kinetics of nitrate and perchlorate removal and biofilm stratification in an ion exchange membrane bioreactor

The biological degradation of nitrate and perchlorate was investigated in an ion exchange membrane bioreactor (IEMB) using a mixed anoxic microbial culture and ethanol as the carbon source. In this process, a membrane-supported biofilm reduces nitrate and perchlorate delivered through an anion exchange membrane from a polluted water stream, containing 60 mg/L of NO₃⁻ and 100 μg/L of ClO₄⁻. Under ammonia limiting conditions, the perchlorate reduction rate decreased by 10%, whereas the nitrate reduction rate was unaffected. Though nitrate and perchlorate accumulated in the bioreactor, their concentrations in the treated water (2.8 ± 0.5 mg/L of NO₃⁻ and 7.0 ± 0.8 μg/L of ClO₄⁻, respectively) were always below the drinking water regulatory levels, due to Donnan dialysis control of the ionic transport in the system.Kinetic parameters determined for the mixed microbial culture in suspension showed that the nitrate reduction rate was 35 times higher than the maximum perchlorate reduction rate. It was found that perchlorate reduction was inhibited by nitrate, since after nitrate depletion perchlorate reduction rate increased by 77%. The biofilm developed in the IEMB was cryosectioned and the microbial population was analyzed by fluorescence in situ hybridization (FISH). The results obtained seem to indicate that the kinetic advantage of nitrate reduction favored accumulation of denitrifiers near the membrane, whereas per(chlorate) reducing bacteria were mainly positioned at the biofilm outer surface, contacting the biomedium. As a consequence of the biofilm stratification, the reduction of perchlorate and nitrate occur sequentially in space allowing for the removal of both ions in the IEMB.     

Elemental characterization of tissues of Octopus vulgaris along the Portuguese coast

The concentrations of V, Mn, Fe, Ni, Cu, Zn, As, Se, Mo, and Pb were measured in digestive gland (DG), branchial hearts (BH), gill (G), and muscle (M) of Octopus vulgaris Cuvier, 1797 caught in three fishing areas of the Portuguese coast, Viana do Castelo, Cascais, and Santa Luzia, for 2 years. The elemental concentrations measured for the different tissues were in accordance with values reported in the literature. The digestive gland presented high concentration levels of Fe, Cu, and Zn, while the branchial hearts showed elevated levels of V, Ni, Mo, as well as Fe and Cu. Significant variations in As, V, Cu, Mo, and Pb tissue concentrations were observed for animals originated from different sampling sites. Pb and As determined in the digestive gland and branchial hearts of animals from Cascais and Santa Luzia, can reflect local environmental characteristics. The variability observed in the elemental concentrations may be useful to further assess the species susceptibility to environmental conditions.     

Estimation of floor acceleration demands in high‐rise buildings during earthquakes

A simplified method to estimate lateral acceleration demands in high‐rise buildings subjected to earthquakes is presented. In the proposed method acceleration demands are obtained by approximating the dynamic characteristics of the building with those of a continuous model consisting of a combination of a flexural cantilever beam and a shear cantilever beam. Closed‐form solutions for mode shapes, period ratios and modal participation factors for the first six modes of vibration are presented. The method is evaluated by comparing peak floor acceleration demands and acceleration time histories computed with the proposed method to those recorded during earthquakes in six instrumented high‐rise buildings. A comparison of floor spectra computed with the approximate method and spectra computed with recorded motions is also presented. Results indicate that the proposed method produces relatively good results with a very small computational effort and requires only a small amount of information about the building. Variations of accelerations demands along the height are closely examined in each building for each component. It is shown that the variation of acceleration demands along the height of high‐rise buildings can differ significantly from that currently recommended in US seismic provisions for anchoring building nonstructural components. Copyright © 2005 John Wiley & Sons, Ltd.