Growth mechanisms of MgO nanocrystals via a sol-gel synthesis using different complexing agents

In the preparation of nanostructured materials, it is important to optimize synthesis parameters in order to obtain the desired material. This work investigates the role of complexing agents, oxalic acid and tartaric acid, in the production of MgO nanocrystals. Results from simultaneous thermogravimetric analysis (STA) show that the two different synthesis routes yield precursors with different thermal profiles. It is found that the thermal profiles of the precursors can reveal the effects of crystal growth during thermal annealing. X-ray diffraction confirms that the final products are pure, single phase and of cubic shape. It is also found that complexing agents can affect the rate of crystal growth. The structures of the oxalic acid and tartaric acid as well as the complexation sites play very important roles in the formation of the nanocrystals. The complexing agents influence the rate of growth which affects the final crystallite size of the materials. Surprisingly, it is also found that oxalic acid and tartaric acid act as surfactants inhibiting crystal growth even at a high temperature of 950°C and a long annealing time of 36 h. The crystallite formation routes are proposed to be via linear and branched polymer networks due to the different structures of the complexing agents.     

Molecular Characterization of α- and β-Thalassaemia among Malay Patients

Both α- and β-thalassaemia syndromes are public health problems in the multi-ethnic population of Malaysia. To molecularly characterise the α- and β-thalassaemia deletions and mutations among Malays from Penang, Gap-PCR and multiplexed amplification refractory mutation systems were used to study 13 α-thalassaemia determinants and 20 β-thalassaemia mutations in 28 and 40 unrelated Malays, respectively. Four α-thalassaemia deletions and mutations were demonstrated. −−^SEA deletion and α^CSα accounted for more than 70% of the α-thalassaemia alleles. Out of the 20 β-thalassaemia alleles studied, nine different β-thalassaemia mutations were identified of which β^E accounted for more than 40%. We concluded that the highest prevalence of (α- and β-thalassaemia alleles in the Malays from Penang are −−^SEA deletion and β^E mutation, respectively.     

Light transmission and haze of polyethylene blown thin films

The surface and bulk morphologies of polyethylene blown films are obtained using non‐contact Atomic Force Microscopy (AFM). Based on these experimental observations, a model using the Mie Scattering theory is proposed to describe the forward transmission and scattering of a plane wave through the film. The light transmission properties are computed from the proposed model and the results are validated by experimental measurements.     

Optimization of biohydrogen production by Clostridium butyricum EB6 from palm oil mill effluent using response surface methodology

Clostridium butyricum EB6 successfully produced hydrogen gas from palm oil mill effluent (POME). In this study, central composite design and response surface methodology were applied to determine the optimum conditions for hydrogen production (P_c) and maximum hydrogen production rate (R_max) from POME. Experimental results showed that the pH, temperature and chemical oxygen demand (COD) of POME affected both the hydrogen production and production rate, both individually and interactively. The optimum conditions for hydrogen production (P_c) were pH 5.69, 36 °C, and 92 g COD/l; with an estimated P_c value of 306 ml H₂/g carbohydrate. The optimum conditions for maximum hydrogen production rate (R_max) were pH 6.52, 41 °C and 60 g COD/l; with an estimated R_max value of 914 ml H₂/h. An overlay study was performed to obtain an overall model optimization. The optimized conditions for the overall model were pH 6.05, 36 °C and 94 g COD/l. The hydrogen content in the biogas produced ranged from 60% to 75%.     

Natural Palm Olein Polyol as a Replacement for Polyether Polyols in Viscoelastic Polyurethane Foam

The impact of replacing three polyether polyols with different levels of a single palm olein‐based natural oil polyol (NOP) was systematically correlated with the changes in foaming reactivity, cell structure, physico‐mechanical properties, and morphology of viscoelastic (VE) foams. The data show that replacing the polyether polyols with the NOP slightly increased the rate of the foaming reactivity. Increasing the NOP content resulted in increased cell size and cells remained fully open. Increased NOP content contributed to higher load bearing properties of VE foam, which can be attributed to higher functionality of NOP compared to polyether polyols. Addition of the NOP slightly increased the resilience of the foams, however, the hysteresis which is the measure of energy absorption remained mostly unaffected. Age properties, characterized by dry and humid compression sets, were mostly unaffected by the replacement of the polyether polyol with the NOP. The addition of NOP did not impact the morphology of the VE foam polymer matrix, which appears to retain a low degree of hard and soft segment domain separation. Overall, the results demonstrate a feasibility that the NOP can be used to partially replace the polyether polyols in VE polyurethane foams without significant impact on the functional performance.     

Investigation on the effect of spinning conditions on the properties of hollow fiber membrane for hemodialysis application

Polyethersulfone (PES) hollow fiber membranes were fabricated via the dry‐wet phase inversion spinning technique, aiming to produce an asymmetric, micro porous ultrafiltration hollow‐fiber specifically for hemodialysis membrane. The objective of this study is to investigate the effect of spinning conditions on the morphological and permeation properties of the fabricated membrane. Among the parameters that were studied in this work are air gap distance, dope extrusion rate, bore fluid flow rate, and the take‐up speed. The contact angle was measured to determine the hydrophilicity of the fibers. Membrane with sufficient hydrophilicity properties is desired for hemodialysis application to avoid fouling and increase its biocompatibility. The influences of the hollow fiber's morphology (i.e., diameter and wall thickness) on the performance of the membranes were evaluated by pure water flux and BSA rejection. The experimental results showed that the dope extrusion rate to bore fluid flow rate ratio should be maintained at 1:1 ratio to produce a perfectly rounded asymmetric hollow fiber membrane. Moreover, the flux of the hollow fiber spun at higher air gap distance had better flux than the one spun at lower air gap distance. Furthermore, spinning asymmetric hollow fiber membranes at high air gap distance helps to produce a thin and porous skin layer, leading to a better flux but a relatively low percentage of rejection for BSA separation. Findings from this study would serve as primary data which will be a useful guide for fabricating a high performance hemodialysis hollow fiber membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43633.     

Synthesis,Characterization and Surface Properties of Amidosulfobetaine Surfactants Bearing Odd-Number Hydrophobic Tail

Three amidosulfobetaine surfactants were synthesized namely: 3-(N-pentadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2a); 3-(N-heptadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2b), and 3-(N-nonadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2c). These surfactants were prepared by direct amidation of commercially available fatty acids with 3-(dimethylamino)-1-propylamine and subsequent reaction with 1,3-propanesultone to obtain quaternary ammonium salts. The synthesized surfactants were characterized by IR, NMR and mass spectrometry. Thermogravimetric analysis (TGA) results showed that the synthesized surfactants have excellent thermal stability with no major thermal degradation below 300 °C. The critical micelle concentration (CMC) values of the surfactants 2a and 2b were found to be 2.2 × 10^?4 and 1.04 × 10^?4 mol/L, and the corresponding surface tension (γ_CMC) values were 33.14 and 34.89 mN m^?1, respectively. The surfactants exhibit excellent surface properties, which are comparable with conventional surfactants. The intrinsic viscosity of surfactant (2b) was studied at various temperatures and concentrations of multi-component brine solution. The plot of natural logarithm of relative viscosity versus surfactant concentration obtained from Higiro et al. model best fit the surfactant behavior. Due to good salt resistance, excellent surface properties and thermal stability, the synthesized surfactant has potential to be used in various oil field applications such as enhanced oil recovery, fracturing, acid diversion, and well stimulation.     

A comparative study of thermal and hydraulic autofrettage

Thermal autofrettage is a potential process to generate beneficial compressive residual stresses at and around the inner wall of a thickwalled cylinder for increasing its pressure carrying capacity. Due to its simplicity and inexpensive arrangement, it can compete with the conventional hydraulic autofrettage process. In this work, a comparative study of the thermal autofrettage and the hydraulic autofrettage is carried out. As the thermal autofrettage does not require hydraulic power pack, the process is more economical than the hydraulic autofrettage. The thermal autofrettage process is also studied for the thick-walled cylindrical vessels subjected to high thermal gradient with or without pressure and is compared with the hydraulic autofrettage. Comparison shows that for cylinders subjected to high thermal gradient without pressure, the thermal autofrettage is superior to the hydraulic autofrettage.