Studies on sublimation of disperse dye out of dyed polymers. I. Rate of sublimation and amorphous transition points of poly(ethylene terephthalate)

Four samples of poly(ethylene terephthalate) film of various crystallinities and orientation were dyed with p-nitroaniline and disperse dyes. When these films were heated under a 2–3 × 10^?3 mm Hg vacuum at a specified temperature T, the dye sublimed out of the dyed specimen. The amount (M_t/M_∞) of sublimed dye is in linear proportion to the square root of the sublimation time, t^½, where M_t and M_∞ are the amounts of dye sublimed for times t and t = ∞. The diffusion coefficient D, calculated from the slope of the above plot, is independent of the dye concentration of the film. When log D is plotted against 1/T°K over the temperature range 320–520°K, the relation is composed of two to four intersecting lines with the slope decreasing with elevation of temperature and with the breaks at about 89°–98°, 122°–135°, 155° and 175°–176°C. These breaks are the amorphous transitions: the first is the glass transition temperature T_g, the second and the fourth are the amorphous transitions corresponding to the crystalline transition points, i.e., the cold crystallization temperature and the smectic–triclinic transition temperature. With some exceptions, these amorphous transitions are found also by dilatometry and electrical conductivity measurements. The apparent activation energy for diffusion decreases from about 100 kcal/mole for the glass state to 22–24 kcal/mole for the region above 180°C. The activation energy for each region changes slightly with the size of dye molecule and the crystallinity and orientation of the film.     

The effects of oxygen diffusion on the surface photooxidation of polystyrene

This paper further illustrates the applicability of multiple internal reflectance infrared spectroscopy to the analysis of near-surface photooxidation. The results are compared with transmission infrared spectra to evaluate compositional gradients resulting from photooxidation and the influence of oxygen diffusion. The sample was a solvent-cast film of atactic, narrow distribution polystyrene, M_w of 100,000, that had been drawn to a ratio of 3.0 at 110°C by solid state coextrusion. Irradiation of these thin films, ～25μm thickness, was performed on exposure to air at 35°C for periods of up to 6 h using a mercury source emitting at 254 nm. On photooxidation, a board peak appears at 3200–3500 cm^?1, attributable to hydroperoxide formation. The most dramatic increase in the infrared spectra is found for a carbonyl band at 1730 cm^?1. It appears to result from an aromatic acid group since it is shifted to 1660 cm^?1 on immersion of the oxidized polystyrene films in aqueous ammonium hydroxide. It is confirmed that the photooxidation of polystyrene occurs preferentially at the surface and that this reaction rate is greatly reduced in the drawn polystyrene film.     

Poly(p-tert-butoxycarbonyloxystyrene): a convenient precursor to p-hydroxystyrene resins

An efficient synthetic route to pure, high molecular weight poly(p-hydroxystyrene) is reported. The route involves synthesis of a new monomer, p-tert-butoxycarbonyloxystyrene, polymerization by radical initiation or by cationic initiation in liquid SO₂, followed by thermolysis or acidolysis of the tert-butoxycarbonyl protecting group. Porous, crosslinked resin beads containing the nucleophilic, phenol pendant group have been prepared in a similar fashion from the precursor terpolymer of p-tert-butoxycarbonyloxystyrene, styrene and divinylbenzene. The utility of this resin for solid-phase synthesis has been demonstrated.     

Change of the amorphous state by heat treatment below the glass transition temperature

This study was undertaken to elucidate the state of a polymer in the amorphous state through a change of motion of the molecular chain caused by heat treatment below the glass transition temperature. From dielectric measurements of amorphous poly(ethylene terephthalate) heat-treated below T_g, it was found that the average relaxation time, the distribution of relaxation time and the dielectric strength increase with increase of heat treatment. From these results, it was concluded that the amorphous state becomes more random by heat treatment.     

Compressibility of the polymer crystal

Results for the compressibilities of a wide range of polymer crystals along the fibre- and the transverse crystal axes are presented. Good agreement is found between the theoretical and the experimental results of different authors.     

Set-based particle swarm optimization with status memory for knapsack problem

Set-based particle swarm optimization (S-PSO) operates on discrete space. S-PSO can solve combinatorial optimization problem with high quality and is successful to apply to the large-scale problem. In S-PSO, a velocity is a set with possibility and a position is a candidate solution. In this paper, we present a novel algorithm of set-based particle swarm optimization with status memory (S-PSOSM) to decide the position based on the previous position for solving knapsack problem. Some operators are redefined for S-PSOSM. S-PSOSM is a simple algorithm because the state of probability reduces. In addition, the weight of S-PSOSM is discussed. S-PSOSM shows high qualities in experimental results.     

Reliability and mechanical durability tests of flexible OLED with ALD coating

To improve the reliability and mechanical durability of a flexible organic light‐emitting diode display, the entire flexible display is coated with an aluminum oxide film by atomic layer deposition (ALD). Because the step coverage of ALD is excellent, the AlO_x film was deposited not only on the front and back surfaces but also on the side surfaces of the display. A high‐temperature and high‐humidity preservation test, repetitive bending tests, and a pencil hardness test were conducted on the flexible display with ALD‐AlO_x coating. The display survived 500 h of a 65°C, 95% preservation test, endured a 100,000‐time repetitive bending test with a curvature radius of 4 mm, and was found to have a pencil hardness of 4H.