Heat transfer to model Newtonian liquid foods in cans during end-over-end rotation

The effect of end-over-end rotation on heat transfer rate to canned Newtonian liquids was studied with two cans (length: diameter $\text{(}\text{L}\text{D}\text{) = 0·73}\text{and}\text{1·37}$) over the range 0–38·6 r.p.m. and radius of rotation 0–14·9 cm. Data were obtained with water, glycerine and 30%, 50%, and 60% sucrose solutions. The agitation induced oscillations of the centre temperature about an increasing average value. The oscillations were more pro-nounced in viscous liquids. The heat transfer coefficient (HTC) was found to be independent of the radius of rotation and $\text{L}\text{D}$. Head space volume between 3 and 9% did not affect the HTC. A correlation was developed in terms of Nusselt, rotational Reynolds, and Prandtl numbers to predict the HTC:

$\text{Nu = 2.9Re}{}^{0.436}\text{Pr}{}^{0.287}$

The characteristic dimension in Nu and Re was the radius of rotation. This correlation, with R² = 92%, is valid for Re: 83 ? 2·1 × 10⁵ and Pr: 2·8 ? 49. Attempts to improve the correlation by incorporating the Grashof number, $\text{L}\text{D}$ and head space volume as well as other characteristic dimensions were not successful.     

X-ray spectroscopy and local structures in glasses

X-ray spectroscopy which is a combination of two techniques, namely x-ray absorption near edge structure (xanes) and extended x-ray absorption fine structure (EXAFS) analyses, is a unique technique for the study of local structures in glasses. Availability of synchrotron radiation sources has made the technique quite attractive and useful because the photon flux from synchrotrons is very intense and polarized. In this article, a brief summary ofxanes andEXAFS techniques is given along with a few applications to the study of local structures in glasses. Communication No. 323 from Solid State and Structural Chemistry Unit.     

Parallel depth first search. Part II. Analysis

This paper presents the analysis of a parallel formulation of depth-first search. At the heart of this parallel formulation is a dynamic work-distribution scheme that divides the work between different processors. The effectiveness of the parallel formulation is strongly influenced by the work-distribution scheme and the target architecture. We introduce the concept of isoefficiency function to characterize the effectiveness of different architectures and work-distribution schemes. Many researchers considered the ring architecture to be quite suitable for parallel depth-first search. Our analytical and experimental results show that hypercube and shared-memory architectures are significantly better. The analysis of previously known work-distribution schemes motivated the design of substantially improved schemes for ring and shared-memory architectures. In particular, we present a work-distribution algorithm that guarantees close to optimal performance on a shared-memory/-network-with-message-combining architecture (e.g. RP3). Much of the analysis presented in this paper is applicable to other parallel algorithms in which work is dynamically shared between different processors (e.g., parallel divide-and-conquer algorithms). The concept of isoefficiency is useful in characterizing the scalability of a variety of parallel algorithms.This work was supported by Army Research Office Grant No. DAAG29-84-K-0060 to the Artificial Intelligence Laboratory, and Office of Naval Research Grant N00014-86-K-0763 to the Computer Science Department at the University of Texas at Austin.     

Structural Studies of TeO2–SeO2–Na2O Glass System

Glass Physics and Chemistry - The growth of nanocrystalization in TeO2–SeO2–Na2O glasses is achieved by the conventional heat treatment method. The influence of Na2O concentration on...     

Impact of communication time delays on combined LFC and AVR of a multi-area hybrid system with IPFC-RFBs coordinated control strategy

In this paper, the impact of communication time delays (CTDs) on combined load frequency control (LFC) and automatic voltage regulation (AVR) of a multi-area system with hybrid generation units is addressed. Investigation reveals that CTDs have significant effect on system performance. A classical PID controller is employed as a secondary regulator and its parametric gains are optimized with a differential evolution - artificial electric field algorithm (DE-AEFA). The superior performance of the presented algorithm is established by comparing with various optimization algorithms reported in the literature. The investigation is further extended to integration of redox flow batteries (RFBs) and interline power flow controller (IPFC) with tie-lines. Analysis reveals that IPFC and RFBs coordinated control enhances system dynamic performance. Finally, the robustness of the proposed control methodology is validated by sensitivity analysis during wide variations of system parameters and load.     

Synthesis and characterization of caprolactone based polyurethane with degradable and antifouling performance

In this work,a degradable polyurethane composed of caprolactone(CL)and L-Lactide(LLA)as soft seg-ments,and 4,4'-methylenebis(cyclohexyl isocyanate)(H12MDI)and polytetramethylene ether glycol(PTMEG)as hard segments,was prepared.Hydrolytic degradation experiment revealed that the degrad-able polyurethane(PU)could be degraded in artificial seawater.It also showed that caprolactone-co-polyurethane(CL-PU)copolymer with higher crystallinity degraded much slower in artificial seawater.However,the introduction of LLA resulted in an increase in the hydrophilicity and reduction in the crys-tallinity of degradable PU,as demonstrated by the contact angle analysis.The result of the scanning elec-tron microscope showed that the surface of degradable PU renewed under static condition.Moreover,degradable PU was able to be used as a carrier,and it controlled the release rate of 4,5-dichloro-2-octyl-isothiazolone(DCOIT).The anti-diatom(Navicula incerta)test demonstrated that the(caprolactone-co-L-lactide)-co-polyurethane 4(CL/LAx-PU4)with DCOIT contents prevented the adhe-sion of diatom Navicula incerta(88.37％reduction)due to their self-polishing and the release of antifou-lants.Therefore,the degradable PU consisted of CL,LLA,and DCOIT could be a durable resin with good antifouling activity for the application in the marine anti-biofouling field.     

Scanning Auger electron spectroscopy study of the oxide film formed on dendritic and interdendritic regions of C containing Fe3Al intermetallic

The oxide films formed during early stage of oxidation at 800 °C on dendritic and interdendritic regions of the cast Fe–16Al–1C (wt.%) alloy were studied using scanning Auger electron spectroscopy. Microhardness measurement and elemental depth profiles by Auger spectroscopy reveal that the carbide, Fe₃AlC_0.69, is the major constituent of the interdendritic region, while dendrites are predominantly Fe₃Al phase. Between the two, the interdendritic region is found to be more prone to oxidation than the dendritic region, which was attributed to presence of carbides with low-Al content. In spite of the difference in oxide film thickness exhibited by both the phases, they consist of an inner aluminium oxide layer and an outer iron oxide layer.     

Towards improved design of boring bars part 1: Dynamic cutting force model with continuous system analysis for the boring bar performance

The vibrational amplitude is generally large in the case of a boring bar due to its slenderness. A dynamic cutting force model has been presented to take this large amplitude into account. The boring bar is then modelled as a cantilever with this dynamic force acting at the free end and a generalized continuous system model is obtained. This model is solved for the specific case of boring with a zero side cutting edge angle for which published results are available. A reasonably close agreement is found between the proposed model and the experimental results.     

Tool deflection compensation in peripheral milling of curved geometries

This paper presents compensation of surface error due to cutting force-induced tool deflections in a peripheral milling process. Previous research attempts on this topic deal with error compensation in machining of straight geometries only. This paper is concerned with peripheral milling of variable curvature geometries where the workpiece curvature changes continuously along the path of cut. In the case of curved geometries, both process geometry and the cutting forces have shown to have strong dependence on workpiece curvature and hence variation of surface error along the path of cut. This calls for a different error compensation strategy than the one which is normally used for machining straight geometries. The present work is an attempt to improve accuracy in machining of curved geometries by use of CNC tool path compensation. Mechanistic model for cutting force estimation and cantilever beam model for cutter deflection estimation are used. The results based on machining experiments performed on a variety of geometries show that the dimensional accuracy can be improved significantly in peripheral milling of curved geometries.