TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

Free volume and permeabilities of O2 and H2 in Nafion membranes for polymer electrolyte fuel cells

The mechanism of gas permeation in Nafion membranes for polymer electrolyte fuel cells has been investigated from the viewpoint of free volume. Three different samples, a membrane with ionic exchange capacity (IEC) = 0.92 meq/g, and recast samples with IEC = 0.92 and 1.00 meq/g were used after drying. Free volume was quantified using the positron annihilation lifetime (PAL) technique and gas permeabilities were measured for O₂ and H₂ as functions of temperature and relative humidity. Good linear correlations between the logarithm of the permeabilities at different temperatures and reciprocal free volume indicate that gas permeation in dry Nafion is governed by the free volume. Nevertheless permeabilities are much smaller than the corresponding flexible chain polymer with a similar free volume size due to stiff chains of the perfluoroethylene backbone. In highly hydrated Nafion above 60% relative humidity, where the O₂ permeability varies oppositely to the free volume, gas permeation proved to be controlled by the gradual increase in overall flexibility of the Nafion–water system.     

Atomic force microscopic study on DNA-wrapping for different diameter single-wall carbon nanotubes

DNA-wrapped single-wall carbon nanotubes (DNA-SWNT hybrids) prepared from different diameter HiPco- and Arc-SWNTs were investigated by atomic force microscopy. The mean diameter of DNA-HiPco-SWNT hybrids is 1.94 nm that is consistent with one HiPco-SWNT (~ 0.9 nm) wrapped by DNA (~ 1 nm). On the other hand, the mean diameter of DNA-Arc-SWNT hybrids is 3.74 nm that can correspond to one Arc-SWNT (~ 1.4 nm) wrapped by several layers of DNA. It is suggested that the DNA-wrapping mechanism for large diameter Arc-SWNTs is different from that for small diameter HiPco-SWNTs.     

Oxidation of methane to formaldehyde over Fe/SiO2 and Sn---W mixed oxides

In an attempt to develop new catalysts for the formation of formaldehyde from methane, the promotion effect of Fe on SiO₂ and that of Sn on WO₃ have been studied. The formation of formaldehyde on silica can be appreciably enhanced by the impregnation of Fe, as far as iron loadings are kept below 0.1 atom.% (Fe/Si × 100). In the case of Sn---W---Ox catalysts, both the addition of Sn to WO₃, and that of W on SnO₂ were effective to the selective formaldehyde formation. Absorption spectra (UV-Vis) and ESR measurements revealed that tetrahedrally coordinated Fe³⁺ in the silica network plays an important role in the formation of formaldehyde. A thin surface layer consisting of W and Sn oxides can account for the selective formaldehyde formation on the Sn---W---Ox catalysts.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

OA&M framework for multiwavelength photonic transport networks

Photonic networks based on wavelength division multiplexing (WDM) and optical path technologies are expected to realize flexible, transparent, and cost-effective transport networks with a large transmission capacity. This paper explores the design framework of photonic transport networks taking into consideration the operation administration and maintenance (OA&M) functions required for the successful introduction of WDM systems based on the optical path concept. From the view point of network maintenance, clear distinction is made between the optical path layer and the optical section layer to facilitate accurate and smooth failure localization. The digital multiplexing span between physical multiplexing interfaces at the end-to-end digital nodes should have the same maintenance span as the corresponding optical path. We argue that cooperative maintenance by OA&M functions at both the digital and optical layers can be a practical way of network supervision. A supervisory (SV) signal transfer method and a configuration that is suitable for the terrestrial trunk network are also indicated. As an example, a practical SV system design methodology and an actual procedure developed for a single channel optical transmission system based on optical in-line amplifiers are introduced. Furthermore, application of the developed SV system and network restoration schemes is discussed for future WDM-based photonic networks. The OA&M aspects introduced will be valuable for creating future photonic network systems     

Production of uniform droplets using membrane, microchannel and microfluidic emulsification devices

This review provides an overview of major microengineering emulsification techniques for production of monodispersed droplets. The main emphasis has been put on membrane emulsification using Shirasu Porous Glass and microsieve membrane, microchannel emulsification using grooved-type and straight-through microchannel plates, microfluidic junctions and flow focusing microfluidic devices. Microfabrication methods for production of planar and 3D poly(dimethylsiloxane) devices, glass capillary microfluidic devices and single-crystal silicon microchannel array devices have been described including soft lithography, glass capillary pulling and microforging, hot embossing, anisotropic wet etching and deep reactive ion etching. In addition, fabrication methods for SPG and microseive membranes have been outlined, such as spinodal decomposition, reactive ion etching and ultraviolet LIGA (Lithography, Electroplating, and Moulding) process. The most widespread application of micromachined emulsification devices is in the synthesis of monodispersed particles and vesicles, such as polymeric particles, microgels, solid lipid particles, Janus particles, and functional vesicles (liposomes, polymersomes and colloidosomes). Glass capillary microfluidic devices are very suitable for production of core/shell drops of controllable shell thickness and multiple emulsions containing a controlled number of inner droplets and/or inner droplets of two or more distinct phases. Microchannel emulsification is a very promising technique for production of monodispersed droplets with droplet throughputs of up to 100?l?h^?1.     

Polymerization via zwitterion 25. Alternating copolymerizations of cyclic acyl phosphorite and phosphite with vinyl monomers having an electron withdrawing group

Summary Spontaneous copolymerizations of cyclic acyl phosphonite (SPO) and phosphite (SPI) with an electron-deficient vinyl monomer such as methyl acrylate (MA), methyl vinyl ketone (MVK), and acrolein (AL), gave the corresponding alternating copolymers. These copolymerizations took place without added initiator and proceeded through zwitterion intermediates. Copolymer structures 1a, 1b, 2 and 3 have been established, all of which were derived in a regiospecific manner of ambident anions. The scheme of the copolymerizations is presented.     

Influence of Metal Ions on the Order-Disorder Transition Temperature of the Ba-M-O (M: La, Y, In, or Ga) System

Preparation of BaLa₂O₄, B_a3,Y₄O₉, B_a,In₂O₅, and Ba₃Ga₂O₆ powders and their sintering were investigated in Ar or air. These sintered bodies with perovskite-related structure were synthesized by reaction sintering, using mixed powders in the atomic ratios of Ba/La = 1, Ba/Y = 0.75, Ba/In = 1, and Ba/Ga = 1.5. The order-disorder transition temperatures of the BaLa₂O₄, Ba₃Y₄O₉, Ba₂In₂O₅, and Ba₃Ga₂O₆ sintered bodies were 270°, 350°, 880°, and 123O^oC, respectively. It was found that the temperatures were influenced by the ionic radius of cations in B sites, and the transition temperatures decreased with increasing ionic radius.