The α–β Transformation in Silicon Nitride Single Crystals

Single crystals of α-Si₃N₄ were annealed at 2000°–2150°C. The β phase was detected after annealing at 2150°C only when the crystals were surrounded by MgO·3Al₂O₃ or Y₂O₃ powders. On the other hand, no evidence of the α–β transformation was found when the crystals were annealed without additives. The solution–precipitation mechanism was concluded to be the dominant factor in the α–β transformation of Si₃N₄.     

High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

Effect of the t–m transformation morphology and stress distribution around the crack path on the measured toughness of zirconia ceramics: A case study on Ce-TZP/alumina nanocomposite

The t–m transformation zone and related residual stress fields around two types of crack used for toughness measurements, i.e. SEVNB (arrested crack induced by a V-notch) and IF methods (indentation crack induced by a Vickers impression), are reported for a Ce-TZP/Al₂O₃ nanocomposite, in comparison with 3Y-TZP. The fact that Ce-TZP/Al₂O₃ exhibits significant high toughness value on occasions when evaluated by the IF method was determined to be clearly linked to the presence of wide ranged three-dimensional transformation configuration and resulting substantial compressive residual stress fields. In contrast, for 3Y-TZP, transformation behaviors around the two types of crack were quite similar, which proves that 3Y-TZP shows near toughness values for both SEVNB and IF methods.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

New Approach for Macro Porous RB‐SiC Derived from SiC/Novolac‐type Phenolic Composite

A novel fabrication route to make macroporous silicon carbide (SiC) has been proposed in this study. The route is composed of the following two steps: the fabrication of porous α‐SiC/novolac‐type phenolic composite using hexamethylenetetramine (HMT) as a curing/blowing agent for the novolac monomer and a conventional reaction‐bonded (RB) sintering of the composite. The α‐SiC/novolac‐type phenolic composite was carbonized at 800°C for 2 h in N₂ gas and then reacted with the molten silicon at 1450°C for 30 min under vacuum, resulting in the macroporous RB‐SiC with an open porosity of 48% and relatively large pore size of ~110 μm. The compressive strength of the macroporous RB‐SiC was 113 MPa, which is relatively high compared to those reported for macroporous SiC of equivalent porosities and pore sizes.     

Influence of the introduction of flexible alkyl chains on the thermal behavior and mechanical properties of mesogenic epoxy thermosets

A mesogenic epoxy resin (DGETAM) was cured with a series of curing agents having different lengths of long alkyl chain (nBAB, n = 4, 8, 12). Properties of the curings were compared with those of the DGEBA cured with the same curing agents revealing the achievement of a balance between certain levels of thermal properties and excellent mechanical properties. Moreover, some curing systems were prepared with twin mesogenic type epoxy resins (DGEnMA, n = 4, 6, 8, 10, 12) having different lengths of alkyl chain as a flexible spacer and the same curing agents (n′BABs). Combinations of the same concentrations of chemical structures in the basic units of the network structure were applied, and the thermal and mechanical properties of their curing systems were investigated. The fracture energy of each system increased considerably with the increase of the alkyl chain length that adjoins the two mesogenic groups in the epoxy resins. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44244.     

In Situ Formation of Hexaferrite Magnets within a 3Y-TZP Matrix: La2O3–ZnO–Fe2O3 and BaO–Fe2O3 Systems

The in situ formation of magnetoplumbite-type (M-type) hexaferrites within a 3Y-TZP matrix was examined for the La₂O₃–ZnO–Fe₂O₃ and BaO–Fe₂O₃ systems. The formation of barium hexaferrite (Ba-M) was rapid enough at a temperature of 1300°C for 2 h to result in a uniform dispersion of fine Ba-M particles in a tetragonal zirconia polycrystal (TZP) matrix. However, the formation of lanthanum-substituted hexaferrite (La-M) was rather sluggish, despite the existence of a charge-compensating divalent oxide. The 3Y-TZP/20-wt%-BaFe₁₂O₁₉ in situ composite possessed good magnetic properties, as well as moderately good mechanical properties.     

Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.