Effect of refrigerant charge on the performance of air conditioning systems

An air conditioning system operates in an optimal condition if the system is fully charged with a specified amount of refrigerant. Poor field maintenance or refrigerant leakage causes low level of charge resulting in a lower thermal performance and higher operating cost. An experimental investigation was conducted to study the effect of low charge level of R‐22 on the performance of a 3‐ton residential air conditioning system. The experimental results show that if a system is undercharged to 90 per cent then the effect is small: a 3.5 per cent reduction in cooling capacity and a 2 per cent increase in the coefficient of performance (COP). However, the system performance suffers serious degradation if the level of charge drops below 80 per cent. An ice layer formed on the outer surface of the cooling coil impedes the heat transfer between the warm air and cold refrigerant vapour. An economic analysis shows that the cost of properly charging an under‐charged system which is at an 85 per cent charge level, can pay for itself in savings in a short period of 3–4 months. Copyright © 2001 John Wiley & Sons, Ltd.     

First and second law analysis of a new power and refrigeration thermodynamic cycle using a solar heat source

The first and second laws of thermodynamics were used to analyze a novel thermodynamic cycle proposed by Goswami in 1995 that uses an ammonia–water binary mixture as the working fluid, while producing both power and refrigeration simultaneously. The thermodynamic performance of the cycle was optimized for maximum second law efficiency using a commercially available optimization program. A maximum second law efficiency of 65.8% was obtained at a heat source temperature of 420 K. An exergy analysis was performed to study losses in different components of the cycle. It is seen that the largest contribution to cycle irreversibility comes from the absorber, with the rectifier and solution heat exchanger also contributing significantly. Irreversibility generation in the boiler is high at very low heat source temperatures, but drops at higher temperatures.     

A review of thermodynamic cycles and working fluids for the conversion of low-grade heat

This paper presents a review of the organic Rankine cycle and supercritical Rankine cycle for the conversion of low-grade heat into electrical power, as well as selection criteria of potential working fluids, screening of 35 working fluids for the two cycles and analyses of the influence of fluid properties on cycle performance. The thermodynamic and physical properties, stability, environmental impacts, safety and compatibility, and availability and cost are among the important considerations when selecting a working fluid. The paper discusses the types of working fluids, influence of latent heat, density and specific heat, and the effectiveness of superheating. A discussion of the 35 screened working fluids is also presented.     

Synthesis,characterization and corrosion performance evaluation of DDR membrane for H2 separation from HI decomposition reaction

An all silica DDR (deca dodecasil rhombohedral) zeolite membrane with dense, interlocked structure has been developed for separation of H₂ from HI/I₂ mixture of HI decomposition reaction. In this work, the DDR zeolite membrane was synthesized on the seeded clay-alumina substrate within 5 days. The seeds were synthesized by sonication mediated hydrothermal process within short crystallization time which enhanced the nucleation for the membrane growth. The synthesized membranes along with seed crystals were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), Field emission scanning electron microscope (FESEM) and energy dispersive X-ray spectroscopy (EDAX). The selectivity of hydrogen with respect to CO₂ and Ar was evaluated by single gas permeation studies at room temperature. The tests for corrosion resistance were carried out upto 120 h with both support and DDR membrane at 130 °C which confirmed the stability of membrane under the harsh HI/I₂ environment.     

Nanoscale Ⅲ-V on Si-based junctionless tunnel transistor for EHF band applications

A single gate Ⅲ-V junctionless tunnel field effect transistor (SG-JLTFET) has been reported which shows excellent dc characteristics at low power supply operation. This device has a thin uniformly n-type doped channel of GaSb i.e. gallium antimonide which is grown epitaxially over silicon substrate. The DC performance parameters such as I_ON, I_ON/I_OFF, average and point subthreshold slope as well as device parameters for analog applications viz. transconductance g_m, transconductance generation efficiency g_m/I_D, various capacitances and the unity gain frequency f_T are studied using a device simulator. Along with examining its endurance to short channel effects, the performances are also compared with a Silicon Dual Gate Junctionless Tunnel FET (DG-JLTFET). The DC and small signal analog performance reflects that GaSb SG-JLTFET has immense purview for extreme high-frequency and low-power applications.     

Laser-Induced Graphene for Electrothermally Controlled,Mechanically Guided, 3D Assembly and Human–Soft Actuators Interaction

Mechanically guided, 3D assembly has attracted broad interests, owing to its compatibility with planar fabrication techniques and applicability to a diversity of geometries and length scales. Its further development requires the capability of on-demand reversible shape reconfigurations, desirable for many emerging applications (e.g., responsive metamaterials, soft robotics). Here, the design, fabrication, and modeling of soft electrothermal actuators based on laser-induced graphene (LIG) are reported and their applications in mechanically guided 3D assembly and human–soft actuators interaction are explored. Over 20 complex 3D architectures are fabricated, including reconfigurable structures that can reshape among three distinct geometries. Also, the structures capable of maintaining 3D shapes at room temperature without the need for any actuation are realized by fabricating LIG actuators at an elevated temperature. Finite element analysis can quantitatively capture key aspects that govern electrothermally controlled shape transformations, thereby providing a reliable tool for rapid design optimization. Furthermore, their applications are explored in human–soft actuators interaction, including elastic metamaterials with human gesture-controlled bandgap behaviors and soft robotic fingers which can measure electrocardiogram from humans in an on-demand fashion. Other demonstrations include artificial muscles, which can lift masses that are about 110 times of their weights and biomimetic frog tongues which can prey insects.     

A compact dual‐band zeroth‐order resonator antenna loaded with meander line inductor

A novel zeroth‐order resonator (ZOR) meta‐material (MTM) antenna with dual‐band is suggested using compound right/left handed transmission line as MTM. In this article, suggested antenna consists of patch through series gap, two meander line inductors, and two circular stubs. The MTM antenna is compact in size which shows dual‐band properties with first band centered at 2.47 GHz (2.05‐2.89 GHz) and second band is centered at 5.9 GHz (3.70‐8.10 GHz) with impedance bandwidth of (S₁₁ < ? 10 dB) 34.69% and 72.45%, respectively. At ZOR mode (2.35 GHz), the suggested antenna has overall dimension of 0.197λ_o × 0.07λ_o × 0.011λ_o with gain of 1.65 dB for ZOR band and 3.35 dB for first positive order resonator band which covers the applications like Bluetooth (2.4 GHZ), TV/Radio/Data (3.700‐6.425 GHz), WLAN (5‐5.16 GHz), C band frequencies (5.15‐5.35, 5.47‐5.725, or 5.725‐5.875 GHz) and satellite communication (7.25‐7.9 GHz). The radiation patterns of suggested structure are steady during the operating band for which sample antenna has been fabricated and confirmed experimentally. It exhibits novel omnidirectional radiation characteristics in phi = 0° plane with lower cross‐polarization values.     

Chemopreventive Effect of Different Ratios of Fish Oil and Corn Oil in Experimental Colon Carcinogenesis

n-3 Polyunsaturated fatty acids (PUFA) have a chemopreventive effect while n-6 PUFA promote carcinogenesis. The effect of these essential fatty acids may be related to oxidative stress. Therefore, the study was designed to evaluate the effect of different ratios of fish oil (FO) and corn oil (CO) in the prevention of colon cancer. Male Wistar rats were divided into control, dimethylhydrazine dihydrochloride (DMH) treated, FO + CO (1:1) and FO + CO (2.5:1). All the groups, except the control received a weekly injection of DMH for 4 weeks. The animals were sacrificed either 48 h later (initiation phase) or kept for 16 weeks (post initiation phase). DMH treatment in the initiation phase animals showed mild to moderate inflammation, decreased ROS and TrxR activity, increased antioxidants, apoptosis and ACF multiplicity. The post initiation study showed severe inflammation with hyperplasia, increased ACF multiplicity and ROS levels, a decrease in antioxidants and apoptosis. The FO + CO (1:1) treated animals showed severe inflammation, a decrease in ROS, an increase in antioxidants and apoptosis in the initiation phase. FO + CO (1:1) in the post initiation phase and FO + CO (2.5:1) in the initiation showed mild inflammation, increased ROS, apoptosis and decreased antioxidants. There was a decrease in ACF multiplicity and ROS levels, increased antioxidants and apoptosis in the post initiation phase study. The present study suggests that FO has a dose- and time-dependent chemopreventive effect in colon cancer mediated through oxidative stress and apoptosis.     

Low temperature sintering of CCTO using P2O5 as a sintering aid

Recent work on CCTO is directed towards decreasing its dissipation factor and further raising its dielectric constant by using different dopants. Also attempts have been made to lower its sintering temperature by adding different sintering aids so as to save energy and use low-cost electrodes (Ag–Pd or base metal) for making multilayer capacitors. Normally, CCTO needs a processing temperature of 1100 °C and above for densification. We report the formation of dense CCTO ceramics at a temperature as low as 1000 °C by adding P₂O₅ as a sintering aid. The samples showed dielectric constant value as high as 40,000, though the dissipation factor values remained high like those reported for pure CCTO.