Colloidal graphenes as heterogeneous additives to enhance protein crystal yield

In the structural analysis of proteins via X-ray diffraction, a rate-limiting step is in favourable nucleation, a problematic obstacle in successful generation of protein crystals. Here graphene and graphene oxide were applied to protein crystallisation trials, offering improvements in crystalline output and nucleation.     

Electrochemical investigation of chromium nanocarbide coated Ti–6Al–4V and Co–Cr–Mo alloy substrates

This study investigated the electrochemical behavior of chromium nano-carbide cermet coating applied on Ti–6Al–4V and Co–Cr–Mo alloys for potential application as wear and corrosion resistant bearing surfaces. The cermet coating consisted of a highly heterogeneous combination of carbides embedded in a metal matrix. The main factors studied were the effect of substrate (Ti–6Al–4V vs. Co–Cr–Mo), solution conditions (physiological vs. 1 M H₂O₂ of pH 2), time of immersion (1 vs. 24 h) and post coating treatments (passivation and gamma sterilization). The coatings were produced with high velocity oxygen fuel (HVOF) thermal spray technique at atmospheric conditions to a thickness of 250 μm then ground and polished to a finished thickness of 100 μm and gamma sterilized. Native Ti–6Al–4V and Co–Cr–Mo alloys were used as controls. The corrosion behavior was evaluated using potentiodynamic polarization, mechanical abrasion and electrochemical impedance spectroscopy under physiologically representative test solution conditions (phosphate buffered saline, pH 7.4, 37 °C) as well as harsh corrosion environments (pH ～ 2, 1 M H₂O₂, T = 65 °C). Severe environmental conditions were used to assess how susceptible coatings are to conditions that derive from possible crevice-like environments, and the presence of inflammatory species like H₂O₂. SEM analysis was performed on the coating surface and cross-section. The results show that the corrosion current values of the coatings (0.4–4 μA/cm²) were in a range similar to Co–Cr–Mo alloy. The heterogeneous microstructure of the coating influenced the corrosion performance. It was observed that the coating impedances for all groups decreased significantly in aggressive environments compared with neutral and also dropped over exposure time. The low frequency impedances of coatings were lower than controls. Among the coated samples, passivated nanocarbide coating on Co–Cr–Mo alloy displayed the least corrosion resistance. However, all the coated materials demonstrated higher corrosion resistance to mechanical abrasion compared to the native alloys.     

The effects of concentration-dependent morphology of self-assembling RADA16 nanoscaffolds on mixed retinal cultures

RADA16 self-assembling peptide nanofiber scaffolds (SAPNSs) have been shown to have positive effects on neural regeneration following injury to the central nervous system in vivo, but mechanisms are unclear. Here we show that RADA16 SAPNSs form scaffolds of increasing fiber density with increasing peptide concentration which in turn has a concentration-dependent effect on neurons and astrocytes in mixed retinal cultures. Importantly, we report that the final nanoscale fiber architecture is an important factor to consider in designing scaffolds to promote regeneration in the central nervous system.     

Experimental investigation of anodized/ spray pyrolysed nanoporous structure on heat transfer augmentation

This paper analyzes the effects of nanoporous surface on heat transfer temperaments of assorted thermal conducting materials. A phenomenal proposal of wielding the surface roughness to ameliorate the heat transfer rate has been discovered. The maximum increase of heat transfer rate procured by nanoporous layers is 133.3% higher than the polished bare metals of surface roughness 0.2 μm. This plays an imperative role in designing compact refrigeration systems, chemical and thermal power plants. Experimental results picture a formidable upswing of 58.3% heat transfer in chemically etched metals of surface roughness 3 μm, 133.3% in nanoporous surface of porosity 75–95 nm formed by electrochemical anodization, and porosity of 40–50 nm formed by spray pyrolysis increases the heat transfer by 130%. Effects of porosity, flow velocity and scaling on the energy transfer are also scrutinized. This paper also analyzes the multifarious modes of nanoporous fabrication, to contrive both prodigious and provident system.     

Bio-diesel as an alternative fuel for diesel engines—A review

The present review aims to study the prospects and opportunities of introducing vegetable oils and their derivatives as fuel in diesel engines. In our country the ratio of diesel to gasoline fuel is 7:1, depicting a highly skewed situation. Thus, it is necessary to replace fossil diesel fuel by alternative fuels. Vegetable oils present a very promising scenario of functioning as alternative fuels to fossil diesel fuel. The properties of these oils can be compared favorably with the characteristics required for internal combustion engine fuels. Fuel-related properties are reviewed and compared with those of conventional diesel fuel. Peak pressure development, heat release rate analysis, and vibration analysis of the engine are discussed in relation with the use of bio-diesel and conventional diesel fuel. Optimization of alkali-catalyzed transesterification of Pungamia pinnata oil for the production of bio-diesel is discussed. Use of bio-diesel in a conventional diesel engine results in substantial reduction in unburned hydrocarbon (UBHC), carbon monoxide (CO), particulate matters (PM) emission and oxide of nitrogen. The suitability of injection timing for diesel engine operation with vegetable oils and its blends, environmental considerations are discussed. Teardown analysis of bio-diesel B20-operated vehicle are also discussed.     

Exfoliation of clay layers in polypropylene matrix using potassium succinate-g-polypropylene as compatibilizer

The efficiency of potassium succinate-g-polypropylene (KPPSA) as compatibilizer for the dispersion of clay in a high molecular weight polypropylene during melt mixing for the preparation of nanocomposites was evaluated and compared with maleic anhydride-g-polypropylene (PPMA). Nanocomposites were prepared by direct melt mixing and by masterbatch methods and the structure obtained was characterized by WAXD and TEM. The exfoliation and better dispersion of the organoclay was observed with KPPSA than PPMA. The dispersion of clay was found to be dependent on the method of preparation, type and the amount of compatibilizer used. The dispersion was better when the nanocomposites were prepared by two step masterbatch route than the single step direct mixing method. Flexural moduli and crystallization behavior were studied and correlated with the dispersion of organoclay in the PP matrix.     

The Interaction of Human and Epstein–Barr Virus miRNAs with Multiple Sclerosis Risk Loci

Although the causes of Multiple Sclerosis (MS) still remain largely unknown, multiple lines of evidence suggest that Epstein–Barr virus (EBV) infection may contribute to the development of MS. Here, we aimed to identify the potential contribution of EBV-encoded and host cellular miRNAs to MS pathogenesis. We identified differentially expressed host miRNAs in EBV infected B cells (LCLs) and putative host/EBV miRNA interactions with MS risk loci. We estimated the genotype effect of MS risk loci on the identified putative miRNA:mRNA interactions in silico. We found that the protective allele of MS risk SNP rs4808760 reduces the expression of hsa-mir-3188-3p. In addition, our analysis suggests that hsa-let-7b-5p may interact with ZC3HAV1 differently in LCLs compared to B cells. In vitro assays indicated that the protective allele of MS risk SNP rs10271373 increases ZC3HAV1 expression in LCLs, but not in B cells. The higher expression for the protective allele in LCLs is consistent with increased IFN response via ZC3HAV1 and so decreased immune evasion by EBV. Taken together, this provides evidence that EBV infection dysregulates the B cell miRNA machinery, including MS risk miRNAs, which may contribute to MS pathogenesis via interaction with MS risk genes either directly or indirectly.     

Construction of broadband passive macromodels from frequency data for simulation of distributed interconnect networks

This paper discusses a method for the construction of multiport broadband passive macromodels using frequency data obtained from an electromagnetic simulation or measurements. This data could represent the frequency response of a distributed interconnect system. The macromodels are generated using rational functions by solving an eigenvalue problem. For numerical computation, the macromodels are represented as a summation of rational functions consisting of low-pass, band-pass, high-pass, and all-pass filters. The stability and passivity of the macromodels are enforced through constraints on the poles and residues of rational functions. To enable the construction of broadband macromodels, methods based on band division, selector, subband reordering, subband dilation, and pole replacement have been used. Two test cases that describe the performance of the proposed algorithm, and three test cases that are representative of distributed systems have been analyzed to verify the efficiency of the method.     

Unintentional zinc diffusion in inp pn-homojunctions

Unintentional zinc diffusion into uniformly Si-doped InP layers has been studied. The sharp non-error function Zn concentration profiles and inflections are shown to be consistent with the substitutional-interstitial mechanism when the influence of the electrostatic field of the pn-junction on diffusion is taken into consideration.