Mechanical and microstructural properties of low-carbon steel-plate-reinforced gray cast iron

In the present experimental study, strengthening of gray cast iron by reinforcing with steel plates was investigated in the as-cast and normalized conditions. Normalizing heat treatments were applied to the specimens at temperatures of 800 °C and 850 °C. Three-point bend specimens were manufactured from gray cast iron and also from gray cast iron with reinforced steel plates. Flexural strengths of the steel-plate-reinforced cast iron were calculated for four distinct volume fractions (V_r = 0.04, 0.08, 0.12, and 0.16). The current study shows that the steel-plate-reinforced gray cast iron has higher flexural strength and flexural modulus than the cast iron without reinforcement. The flexural strength considerably increases with slight increase in normalization temperature. Optical and scanning electron microscopy analyses were used to examine flake morphology and microstructures of gray cast iron and steel-plate-reinforced gray cast iron. It is noted that carbon diffuses from the gray cast iron to the steel plates. A transition region containing partially dissolved graphite and having high hardness was observed due to the carbon diffusion.     

The production of β-SiAlON ceramics with low amounts of additive,at low sintering temperature

In the present work nano-sized powder of β-SiAlON was produced using a wet milling process. Different milling times and mediums (methyl ethyl keton, ethanol and toluene as solvents, polyethyleneglicol, oleic acid, sodium tripolyphosphate and polyvinylpyrrolidon as dispersants) were performed for the determination of the most efficient milling system. The powders were produced using a conventional process (the ball to powder ratio was 1:1.5, at 300 rpm, for 1.5 h) having a few hundred nanometer particle size, and these were used as standard powders in this study. The nano-sized β-SiAlON starting powders (<100 nm) were sintered at lower temperatures than that of the conventional powders. The amount of Y₂O₃ in powders (～130 nm), produced by high energy milling process, was fewer than conventional powders (5 wt.%). The results of the powder size, sintering behavior and mechanical properties of this sample were compared to those of the standard powder and its sintered sample. This sample, produced using the nano-powder, was investigated, and densified at 150 °C lower than that of the standard sample. Even though the amount of Y₂O₃ was decreased, the hardness of the samples was better than that of the standard sample.     

Optimization of Multireservoir Systems by Genetic Algorithm

Application of optimization techniques for determining the optimal operating policy of reservoirs is a major issue in water resources planning and management. As an optimization Genetic Algorithm, ruled by evolution techniques, have become popular in diversified fields of science. The main aim of this study is to explore the efficiency and effectiveness of genetic algorithm in optimization of multi-reservoirs. A computer code has been constructed for this purpose and verified by means of a reference problem with a known global optimum. Three reservoirs in the Colorado River Storage Project were optimized for maximization of energy production. Besides, a real-time approach utilizing a blend of online and a posteriori data was proposed. The results obtained were compared to the real operational data and genetic algorithm was found to be effective and can be utilized as an alternative technique to other traditional optimization techniques.     

The influence of different circular hole perforations on interlaminar shear strength of a novel fiber metal laminates

This study characterizes surface treated classic type fiber metal laminates (FMLs) interlaminar shear strength (ILSS) based on a glass mat reinforced polyphenylene sulphide composite and an aluminum alloy. The effect of concentration of γ‐glycidoxypropyltrimethoxysilane surface treatment on ILSS of adhesive bonding between aluminum sheet and composite laminates has been investigated. After determining the silane concentration, novel FML material is manufactured using a compression moulding process which involves aluminum sheets with different circular hole perforations (Array type A and B) with two circular hole diameters (ϕ3 and ϕ5 mm) and two total hole area/closed area: 0.05 and 0.06) to develop mechanical interlocking between aluminum layers and composite laminates. Tensile tests are performed to investigate the effect of different circular hole perforations on ILSS properties of FMLs. Test results show that ILSS is improved with increasing the circular hole diameter and decreased with the number of holes as correlated with undrilled FMLs. Failure modes, damage initiation, and progression of FMLs with different open hole perforations are determined with optical microscope. POLYM. COMPOS., 37:963–973, 2016. © 2014 Society of Plastics Engineers     

Cooperative Communications in Future Home Networks

The basic idea behind cooperative communications is that mobile terminals collaborate to send data to each other. This effectively adds diversity in the system and improves the overall performance. In this paper, we investigate the potential gains of cooperative communication in future home networks. We derive analytical expressions for the error probability of binary phase shift keying (BPSK) signals over Nakagami-m fading channels in a multi relay communication network. Following to the analytical study, we analyze the contribution of cooperative relaying to the 60GHz network connectivity through simulations using a realistic indoor environment model. We compare the performance of different relay configurations under variable obstacle densities. We show that a typical 60GHz indoor network should employ either a multi-relay configuration or a single-relay configuration with a smart relay selection mechanism to achieve acceptable outage rates. In the use of multiple-relay configuration, both analytical and simulation studies indicate that increasing the number of cooperative relays does not improve the system performance significantly after a certain threshold.     

Effect of conductive layer on the performance of gel electrolyte-based supercapacitors

Solid-state electrolytes such a further novel finding is going to have great importance because of the disadvantages of liquid electrolytes such as electrochemical instability, low ion selectivity, and interface contact. It is anticipated that the use of solid-state electrolytes including supercapacitors (SCs) will become widespread with decreasing self-leakage and environmental damage more than liquid electrolytes. In this study, SCs with graphene/PEDOT: PSS coated electrodes and binary PVA gel electrolytes with a conductive layer were designed and the electrochemical performance of the configurations was characterized. The effects of the conductive layer between binary electrolytes and the concentration of the KOH solution in the electrolytes were studied. It was observed that the conductive layer used between the gel electrolytes causes additional charging at the electrolyte/conductive layer interface and behaves like a serially connected capacitor to the double-layer capacitor. Interestingly, at a slow sweep rate (5 mV/s), the specific capacitance values of the assembled SCs decreased when a conductive layer was used but it increased when the sweep rate was fast (100 mV/s).     

Drying kinetics,colour, total phenolic content and antioxidant capacity properties of kiwi dried by different methods

This study analysed the convective (60, 70 and 80° C), microwave (120 and 350 W) and freeze drying methods in terms of their effects on the drying characteristics, colour, total phenolic content (TPC) and antioxidant capacity of kiwi slices. Nine different mathematical models were applied to experimental data to achieve the most accurate calculation for drying curves. The Midilli et al. and Wang and Singh models proved to be the most suitable at explaining the drying kinetics of kiwi samples as compared to other models according to the statistical tests. Each drying method was significantly affected by colour parameters (L*, a*, b*, C, α and ΔE). The dried samples exhibited respectively 5–49 % and 10–47 % less TPC and antioxidant capacity compared to the fresh sample. According to the correlation analysis conducted between TPC and antioxidant capacity for kiwi slices, there is a positive correlation (R ²  = 0.7796). Microwave dried samples at 120 W particularly had the lowest TPC and antioxidant capacity. Freeze drying method yielded the closest values with respect to colour values, total phenol content and antioxidant capacity to those of fresh samples when compared to the other methods.     

Challenges in Developing a Bessel-Beam Based Ultrafast Ablation Probe

Instruments and Experimental Techniques - With its elongated depth of focus, Bessel beams offer rapid and high aspect ratio ablation capability, in contrast to Gaussian beam counterparts. In this...