Improvement of Mg–Al alloys for hydrogen storage applications

In the context of energy carrier, storage of hydrogen is one of the key challenges for research today. The group of Mg-based hydrides stands as a promising candidate for competitive hydrogen storage with high reversible hydrogen capacity.     

Correlation between voltage holding capability and light emission in a 500 keV electrostatic accelerator utilized for fusion application

Voltage holding capability in a 500 keV electrostatic accelerator with large FRP insulators was examined without the beam acceleration. When high voltage was applied, the light with a broad peak at a wavelength of 420 nm was mostly emitted inside the accelerator even though breakdown did not occur. The voltage holding capability has a strong correlation with the light intensity. Stable voltage holding was realized under the conditions in which light emission was well suppressed.     

Diethyl ketone‐based imine as efficient latent hardener for epoxy resin

Several imines were synthesized and evaluated as water‐initiated hardener for epoxy resin. Imines with a lower electron density on the C=N carbon showed a faster hydrolysis rate. Diethyl ketone‐based imines were the most efficiently hydrolyzed among the imines examined, and the adhesive properties of epoxy resin with diimines used as the hardeners were evaluated. A novel diethyl ketone‐based diimine, N,N′‐di(1‐ethylpropylidene)‐m‐xylylenediamine (10), served as an efficient latent hardener of epoxy resin. Epikote 828 containing 10, filler, and dryer increased the adhesive strength faster than Epikote 828 containing filler and dryer with methyl isobutyl ketone‐based imine. The mixed system of epoxy resin and 10 showed good storage stability at room temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1744–1749, 2002     

Porous-microelectrode study on Pt/C catalysts for methanol electrooxidation

We have developed a porous-microelectrode (PME) to investigate the electroactivity of catalyst particles for proton exchange membrane fuel cells. The cavity at the tip of the PME was filled with Pt/C catalysts prepared by impregnation method. Cyclic voltammograms (CVs) recorded in 1 N H₂SO₄ aqueous solution revealed that the active area of the stacked catalysts exist not only at the surface but also inside of the stack. For methanol electrooxidation, 30 wt.% Pt/C exhibited the highest electroactivity, whereas the 50 wt.% Pt/C showed extremely small current. The small current is considered as a result of a small active-surface area. Methanol oxidation peak potential shifted toward cathodic direction as Pt-loading decreased, which agrees well with the Pt-oxide formation potential. The activation energy for methanol oxidation was assessed to be 44±3 kJ mol⁻¹ for all Pt/C catalysts and Pt-disc electrode.     

One‐pot curing system of epoxy resin imines initiated with water

The curing and adhesive properties of one‐component epoxy resins containing Epikote 828 and diimines, derived from N,N′‐di(1‐ethylpropylidene)‐m‐xylylenediamine, N,N′‐di(1‐ethylpropylidene)‐1,3‐diaminomethylcyclohexane (2), and N,N′‐di(1,3‐dimethylbutylidene)‐m‐xylylenediamine, which were used as water‐initiated hardeners, were examined. Diethyl ketone‐based imines with a lower electron density on the C?N carbon were efficiently hydrolyzed and showed curing activity. 2, a novel diethyl ketone‐based diimine, served as an efficient latent hardener of the epoxy resin. A paste of the epoxy resin with 2 showed good storage stability at room temperature and good adhesive properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 878–882, 2003     

Interactive solution to multiple criteria problems in chemical process design: An approach by pairwise comparison

A process design problem is considered as a multiobjective problem that is characterized by conflicting objectives such as economics, operability, and so on. A method developed for solving multiobjective problems in man-machine interactive mode has been extensively applied to the basic process design of chemical process systems. AS an illustrative example, an optimal design of a simple, yet practical, chemical process system has been taken up to show the practical usefulness of the present method.     

LC-CAD: A CAD system for life cycle design

In product life cycle design, a designer should design both a product and its life cycle. Although CAD systems for product design are popular, there are no CAD systems for life cycle design. This paper proposes LC-CAD (Life Cycle-CAD) that represents a product and its life cycle in an integrated manner, manages consistency between these two models, and describes changes of a product along its life cycle (e.g., a component is shredded into fragments of metal in a recycling process). LC-CAD also evaluates environmental, economic, and other performance of designed life cycle using life cycle simulation.     

Advanced Mechanical Properties of a Powder Metallurgy Ti-Al-N Alloy Doped with Ultrahigh Nitrogen Concentration

Titanium and its alloys are recognized for their attractive properties. However, high-performance Ti alloys are often alloyed with rare or noble-metal elements. In the present study, Ti alloys doped with only ubiquitous elements were produced via powder metallurgy. The experimental results showed that pure Ti with 1.5 wt.% AlN incorporated exhibited excellent tensile properties, superior to similarly extruded Ti-6Al-4V. Further analysis revealed that its remarkably advanced strength could primarily be attributed to nitrogen solid-solution strengthening, accounting for nearly 80% of the strength increase of the material. In addition, despite the ultrahigh nitrogen concentration up to 0.809 wt.%, the Ti-1.5AlN sample showed elongation to failure of ~ 10%. This result exceeds the well-known limitation for nitrogen (over 0.45 wt.%) that causes embrittlement of Ti alloys.     

Preparation of a crosslinked polyelectrolyte membrane for fuel cells with an allyl methacrylate based two‐step reaction

In this study, a proton‐exchange membrane for fuel cells was prepared via a two‐step reaction with an allyl methacrylate (AMA) as an asymmetric crosslinking agent. First, a linear‐chain polymer was synthesized, consisting of hydrophilic 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS), hydrophobic 2,2,2‐trifluoroethyl methacrylate (TFEMA), and AMA. Subsequently, we crosslinked the linear‐chain polymer by reacting the remaining allyl group during dry heating. The proton conductivity of the prepared membrane was 7 × 10^?2 S/cm at room temperature. The membrane was characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, and atomic force microscopy. The polymer electrolyte membrane fuel cell (PEMFC) performance was evaluated for a membrane electrode assembly composed of the crosslinked AMPS–TFEMA–AMA/ fluoroalkyl graft polymer (FGP) membrane. As a result of a power‐generation test, a maximum power density of 174 mW/cm² at a current density of 400 mA/cm² was observed for a PEMFC single cell. Consequently, it was confirmed that the AMPS–TFEMA–AMA/FGP membrane for PEMFC could easily be prepared via a two‐step reaction at a low cost and that PEMFC exhibited a cell performance and that of cells with the Nafion membrane. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Surface and bulk properties of Cu nanocluster composites in LiNbO3

Implantation of 60 keV Cu⁻ ions into LiNbO₃ resulted in formation of complex nanocomposites consisting of metal Cu nanoparticles distributed among nanodomains of the host medium. The nanodomains of the host medium correspond to regions of a few hundred naometers in diameter with a constant refractive index. Distributions of the Cu nanoparticles and nanodomains in the implanted region do not correlate with each other. Variations of linear and non-linear optical absorption of the nanocomposites are mainly determined by the change of chemical composition and structure of implanted regions of LiNbO₃.